From: Dmitry Osipenko <digetx@gmail.com>
To: Peter De Schrijver <pdeschrijver@nvidia.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Thierry Reding <thierry.reding@gmail.com>,
Jonathan Hunter <jonathanh@nvidia.com>,
Joseph Lo <josephl@nvidia.com>
Cc: devicetree@vger.kernel.org, linux-tegra@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v1 1/3] dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller
Date: Fri, 12 Apr 2019 02:02:19 +0300 [thread overview]
Message-ID: <20190411230221.31362-2-digetx@gmail.com> (raw)
In-Reply-To: <20190411230221.31362-1-digetx@gmail.com>
Add device-tree binding for NVIDIA Tegra30 External Memory Controller.
The binding is based on the Tegra124 EMC binding since hardware is
similar, although there are couple significant differences.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
.../memory-controllers/nvidia,tegra30-emc.txt | 257 ++++++++++++++++++
1 file changed, 257 insertions(+)
create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt
diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt
new file mode 100644
index 000000000000..dffe396c5d79
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt
@@ -0,0 +1,257 @@
+NVIDIA Tegra30 SoC EMC (external memory controller)
+====================================================
+
+Required properties :
+- compatible : Should be "nvidia,tegra30-emc".
+- reg : physical base address and length of the controller's registers.
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- interrupts : Should contain EMC General interrupt.
+- clocks : Should contain EMC clock.
+- nvidia,memory-controller : phandle of the MC driver.
+
+The node should contain a "emc-timings" subnode for each supported RAM type
+(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address
+being its RAM_CODE.
+
+Required properties for "emc-timings" nodes :
+- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is
+used for.
+
+Each "emc-timings" node should contain a "timing" subnode for every supported
+EMC clock rate. The "timing" subnodes should have the clock rate in Hz as
+their unit address.
+
+Required properties for "timing" nodes :
+- clock-frequency : Should contain the memory clock rate in Hz.
+- The following properties contain EMC timing characterization values
+(specified in the board documentation) :
+ - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL
+ - nvidia,emc-mode-1 : Mode Register 1
+ - nvidia,emc-mode-2 : Mode Register 2
+ - nvidia,emc-mode-reset : Mode Register 0
+ - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change
+ - nvidia,emc-cfg-dyn-self-ref : dynamic self-refresh enabled
+ - nvidia,emc-cfg-periodic-qrst : FBIO "read" FIFO periodic resetting enabled
+- nvidia,emc-configuration : EMC timing characterization data. These are the
+registers (see section "18.13.2 EMC Registers" in the TRM) whose values need to
+be specified, according to the board documentation:
+
+ EMC_RC
+ EMC_RFC
+ EMC_RAS
+ EMC_RP
+ EMC_R2W
+ EMC_W2R
+ EMC_R2P
+ EMC_W2P
+ EMC_RD_RCD
+ EMC_WR_RCD
+ EMC_RRD
+ EMC_REXT
+ EMC_WEXT
+ EMC_WDV
+ EMC_QUSE
+ EMC_QRST
+ EMC_QSAFE
+ EMC_RDV
+ EMC_REFRESH
+ EMC_BURST_REFRESH_NUM
+ EMC_PRE_REFRESH_REQ_CNT
+ EMC_PDEX2WR
+ EMC_PDEX2RD
+ EMC_PCHG2PDEN
+ EMC_ACT2PDEN
+ EMC_AR2PDEN
+ EMC_RW2PDEN
+ EMC_TXSR
+ EMC_TXSRDLL
+ EMC_TCKE
+ EMC_TFAW
+ EMC_TRPAB
+ EMC_TCLKSTABLE
+ EMC_TCLKSTOP
+ EMC_TREFBW
+ EMC_QUSE_EXTRA
+ EMC_FBIO_CFG6
+ EMC_ODT_WRITE
+ EMC_ODT_READ
+ EMC_FBIO_CFG5
+ EMC_CFG_DIG_DLL
+ EMC_CFG_DIG_DLL_PERIOD
+ EMC_DLL_XFORM_DQS0
+ EMC_DLL_XFORM_DQS1
+ EMC_DLL_XFORM_DQS2
+ EMC_DLL_XFORM_DQS3
+ EMC_DLL_XFORM_DQS4
+ EMC_DLL_XFORM_DQS5
+ EMC_DLL_XFORM_DQS6
+ EMC_DLL_XFORM_DQS7
+ EMC_DLL_XFORM_QUSE0
+ EMC_DLL_XFORM_QUSE1
+ EMC_DLL_XFORM_QUSE2
+ EMC_DLL_XFORM_QUSE3
+ EMC_DLL_XFORM_QUSE4
+ EMC_DLL_XFORM_QUSE5
+ EMC_DLL_XFORM_QUSE6
+ EMC_DLL_XFORM_QUSE7
+ EMC_DLI_TRIM_TXDQS0
+ EMC_DLI_TRIM_TXDQS1
+ EMC_DLI_TRIM_TXDQS2
+ EMC_DLI_TRIM_TXDQS3
+ EMC_DLI_TRIM_TXDQS4
+ EMC_DLI_TRIM_TXDQS5
+ EMC_DLI_TRIM_TXDQS6
+ EMC_DLI_TRIM_TXDQS7
+ EMC_DLL_XFORM_DQ0
+ EMC_DLL_XFORM_DQ1
+ EMC_DLL_XFORM_DQ2
+ EMC_DLL_XFORM_DQ3
+ EMC_XM2CMDPADCTRL
+ EMC_XM2DQSPADCTRL2
+ EMC_XM2DQPADCTRL2
+ EMC_XM2CLKPADCTRL
+ EMC_XM2COMPPADCTRL
+ EMC_XM2VTTGENPADCTRL
+ EMC_XM2VTTGENPADCTRL2
+ EMC_XM2QUSEPADCTRL
+ EMC_XM2DQSPADCTRL3
+ EMC_CTT_TERM_CTRL
+ EMC_ZCAL_INTERVAL
+ EMC_ZCAL_WAIT_CNT
+ EMC_MRS_WAIT_CNT
+ EMC_AUTO_CAL_CONFIG
+ EMC_CTT
+ EMC_CTT_DURATION
+ EMC_DYN_SELF_REF_CONTROL
+ EMC_FBIO_SPARE
+ EMC_CFG_RSV
+
+Example SoC include file:
+
+/ {
+ emc@7000f400 {
+ compatible = "nvidia,tegra30-emc";
+ reg = <0x7000f400 0x400>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA30_CLK_EMC>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nvidia,memory-controller = <&mc>;
+ };
+};
+
+Example board file:
+
+/ {
+ emc@7000f400 {
+ emc-timings-1 {
+ nvidia,ram-code = <1>;
+
+ timing-667000000 {
+ clock-frequency = <667000000>;
+
+ nvidia,emc-auto-cal-interval = <0x001fffff>;
+ nvidia,emc-mode-1 = <0x80100002>;
+ nvidia,emc-mode-2 = <0x80200018>;
+ nvidia,emc-mode-reset = <0x80000b71>;
+ nvidia,emc-zcal-cnt-long = <0x00000040>;
+ nvidia,emc-cfg-dyn-self-ref = <0x00000000>;
+ nvidia,emc-cfg-periodic-qrst = <0x00000001>;
+
+ nvidia,emc-configuration = <
+ 0x00000020 /* EMC_RC */
+ 0x0000006a /* EMC_RFC */
+ 0x00000017 /* EMC_RAS */
+ 0x00000007 /* EMC_RP */
+ 0x00000005 /* EMC_R2W */
+ 0x0000000c /* EMC_W2R */
+ 0x00000003 /* EMC_R2P */
+ 0x00000011 /* EMC_W2P */
+ 0x00000007 /* EMC_RD_RCD */
+ 0x00000007 /* EMC_WR_RCD */
+ 0x00000002 /* EMC_RRD */
+ 0x00000001 /* EMC_REXT */
+ 0x00000000 /* EMC_WEXT */
+ 0x00000007 /* EMC_WDV */
+ 0x0000000a /* EMC_QUSE */
+ 0x00000009 /* EMC_QRST */
+ 0x0000000b /* EMC_QSAFE */
+ 0x00000011 /* EMC_RDV */
+ 0x00001412 /* EMC_REFRESH */
+ 0x00000000 /* EMC_BURST_REFRESH_NUM */
+ 0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+ 0x00000002 /* EMC_PDEX2WR */
+ 0x0000000e /* EMC_PDEX2RD */
+ 0x00000001 /* EMC_PCHG2PDEN */
+ 0x00000000 /* EMC_ACT2PDEN */
+ 0x0000000c /* EMC_AR2PDEN */
+ 0x00000016 /* EMC_RW2PDEN */
+ 0x00000072 /* EMC_TXSR */
+ 0x00000200 /* EMC_TXSRDLL */
+ 0x00000005 /* EMC_TCKE */
+ 0x00000015 /* EMC_TFAW */
+ 0x00000000 /* EMC_TRPAB */
+ 0x00000006 /* EMC_TCLKSTABLE */
+ 0x00000007 /* EMC_TCLKSTOP */
+ 0x00001453 /* EMC_TREFBW */
+ 0x0000000b /* EMC_QUSE_EXTRA */
+ 0x00000006 /* EMC_FBIO_CFG6 */
+ 0x00000000 /* EMC_ODT_WRITE */
+ 0x00000000 /* EMC_ODT_READ */
+ 0x00005088 /* EMC_FBIO_CFG5 */
+ 0xf00b0191 /* EMC_CFG_DIG_DLL */
+ 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+ 0x00000008 /* EMC_DLL_XFORM_DQS0 */
+ 0x00000008 /* EMC_DLL_XFORM_DQS1 */
+ 0x00000008 /* EMC_DLL_XFORM_DQS2 */
+ 0x00000008 /* EMC_DLL_XFORM_DQS3 */
+ 0x0000000a /* EMC_DLL_XFORM_DQS4 */
+ 0x0000000a /* EMC_DLL_XFORM_DQS5 */
+ 0x0000000a /* EMC_DLL_XFORM_DQS6 */
+ 0x0000000a /* EMC_DLL_XFORM_DQS7 */
+ 0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+ 0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+ 0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+ 0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+ 0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+ 0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+ 0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+ 0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+ 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+ 0x0000000a /* EMC_DLL_XFORM_DQ0 */
+ 0x0000000a /* EMC_DLL_XFORM_DQ1 */
+ 0x0000000a /* EMC_DLL_XFORM_DQ2 */
+ 0x0000000a /* EMC_DLL_XFORM_DQ3 */
+ 0x000002a0 /* EMC_XM2CMDPADCTRL */
+ 0x0800013d /* EMC_XM2DQSPADCTRL2 */
+ 0x22220000 /* EMC_XM2DQPADCTRL2 */
+ 0x77fff884 /* EMC_XM2CLKPADCTRL */
+ 0x01f1f501 /* EMC_XM2COMPPADCTRL */
+ 0x07077404 /* EMC_XM2VTTGENPADCTRL */
+ 0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+ 0x080001e8 /* EMC_XM2QUSEPADCTRL */
+ 0x0c000021 /* EMC_XM2DQSPADCTRL3 */
+ 0x00000802 /* EMC_CTT_TERM_CTRL */
+ 0x00020000 /* EMC_ZCAL_INTERVAL */
+ 0x00000100 /* EMC_ZCAL_WAIT_CNT */
+ 0x0155000c /* EMC_MRS_WAIT_CNT */
+ 0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+ 0x00000000 /* EMC_CTT */
+ 0x00000000 /* EMC_CTT_DURATION */
+ 0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+ 0xe8000000 /* EMC_FBIO_SPARE */
+ 0xff00ff49 /* EMC_CFG_RSV */
+ >;
+ };
+ };
+ };
+};
--
2.21.0
next prev parent reply other threads:[~2019-04-11 23:02 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-11 23:02 [PATCH v1 0/3] memory: Introduce NVIDIA Tegra30 EMC driver Dmitry Osipenko
2019-04-11 23:02 ` Dmitry Osipenko [this message]
2019-04-11 23:02 ` [PATCH v1 2/3] memory: tegra: Introduce " Dmitry Osipenko
2019-04-12 14:01 ` Dmitry Osipenko
2019-04-11 23:02 ` [PATCH v1 3/3] ARM: dts: tegra30: Add External Memory Controller node Dmitry Osipenko
2019-04-12 8:01 ` Peter De Schrijver
2019-04-12 8:01 ` Peter De Schrijver
2019-04-12 10:09 ` Dmitry Osipenko
2019-04-12 8:06 ` Peter De Schrijver
2019-04-12 8:06 ` Peter De Schrijver
2019-04-12 10:11 ` Dmitry Osipenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190411230221.31362-2-digetx@gmail.com \
--to=digetx@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=josephl@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pdeschrijver@nvidia.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.