From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To: linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
stable@vger.kernel.org, Helen Koike <helen.koike@collabora.com>,
Eric Anholt <eric@anholt.net>,
"Sasha Levin (Microsoft)" <sashal@kernel.org>
Subject: [PATCH 4.9 04/32] ARM: dts: bcm283x: Fix hdmi hpd gpio pull
Date: Thu, 2 May 2019 17:20:50 +0200 [thread overview]
Message-ID: <20190502143316.405963045@linuxfoundation.org> (raw)
In-Reply-To: <20190502143314.649935114@linuxfoundation.org>
[ Upstream commit 544e784188f1dd7c797c70b213385e67d92005b6 ]
Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 84df85ea6296..7efde03daadd 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -26,5 +26,5 @@
};
&hdmi {
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
--
2.19.1
next prev parent reply other threads:[~2019-05-02 15:50 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-02 15:20 [PATCH 4.9 00/32] 4.9.173-stable review Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 01/32] usbnet: ipheth: prevent TX queue timeouts when device not ready Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 02/32] usbnet: ipheth: fix potential null pointer dereference in ipheth_carrier_set Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 03/32] media: vivid: check if the cec_adapter is valid Greg Kroah-Hartman
2019-05-02 15:20 ` Greg Kroah-Hartman [this message]
2019-05-02 15:20 ` [PATCH 4.9 05/32] s390: limit brk randomization to 32MB Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 06/32] qlcnic: Avoid potential NULL pointer dereference Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 07/32] netfilter: nft_set_rbtree: check for inactive element after flag mismatch Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 08/32] netfilter: bridge: set skb transport_header before entering NF_INET_PRE_ROUTING Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 09/32] sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init() Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 10/32] serial: ar933x_uart: Fix build failure with disabled console Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 11/32] usb: gadget: net2280: Fix overrun of OUT messages Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 12/32] usb: gadget: net2280: Fix net2280_dequeue() Greg Kroah-Hartman
2019-05-02 15:20 ` [PATCH 4.9 13/32] usb: gadget: net2272: Fix net2272_dequeue() Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 14/32] ARM: dts: pfla02: increase phy reset duration Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 15/32] net: ks8851: Dequeue RX packets explicitly Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 16/32] net: ks8851: Reassert reset pin if chip ID check fails Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 17/32] net: ks8851: Delay requesting IRQ until opened Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 18/32] net: ks8851: Set initial carrier state to down Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 19/32] staging: rtl8712: uninitialized memory in read_bbreg_hdl() Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 20/32] NFS: Fix a typo in nfs_init_timeout_values() Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 21/32] net: xilinx: fix possible object reference leak Greg Kroah-Hartman
2019-05-02 15:21 ` Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 22/32] net: ibm: " Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 23/32] net: ethernet: ti: " Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 24/32] scsi: qla4xxx: fix a potential NULL pointer dereference Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 25/32] usb: u132-hcd: fix resource leak Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 26/32] ceph: fix use-after-free on symlink traversal Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 27/32] scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 28/32] libata: fix using DMA buffers on stack Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 29/32] gpio: of: Fix of_gpiochip_add() error path Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 30/32] kconfig/[mn]conf: handle backspace (^H) key Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 31/32] leds: pca9532: fix a potential NULL pointer dereference Greg Kroah-Hartman
2019-05-02 15:21 ` [PATCH 4.9 32/32] vfio/type1: Limit DMA mappings per container Greg Kroah-Hartman
2019-05-02 23:06 ` [PATCH 4.9 00/32] 4.9.173-stable review kernelci.org bot
2019-05-03 7:04 ` Naresh Kamboju
2019-05-03 9:27 ` Jon Hunter
2019-05-03 9:27 ` Jon Hunter
2019-05-03 17:15 ` Guenter Roeck
2019-05-03 21:21 ` shuah
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190502143316.405963045@linuxfoundation.org \
--to=gregkh@linuxfoundation.org \
--cc=eric@anholt.net \
--cc=helen.koike@collabora.com \
--cc=linux-kernel@vger.kernel.org \
--cc=sashal@kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.