Re: [PATCH v2] arm64: dts: imx8mm-evk: Add BD71847 PMIC

[Shawn Guo <shawnguo@kernel.org>]

On Tue, Apr 23, 2019 at 02:16:48PM +0000, Leonard Crestez wrote:
> The BUCK2 regulator is used for cpufreq voltage control, otherwise
> configuration is mostly static.
> 
> This uses the newly-implemented rohm,reset-snvs-powered property to
> properly handle the SNVS state of imx8mm.
> 
> Between BD71837 and BD71847 the BUCK3/4 regulators were removed but
> datasheet and board schematics kept the names for BUCK5/6/7/8. The
> driver however renumbered 5/6/7/8 to 3/4/5/6. Use the names from DT
> bindings and add comments to signal this.
> 
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
> 
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 131 +++++++++++++++++++
>  1 file changed, 131 insertions(+)
> 
> Changes since v1:
>  - Move compatible property first
>  - Remove address/size numbering from regulators list
> Link: https://marc.info/?l=linux-clk&m=155530430429151&w=2
> 
> Other imx8mm cpufreq patches in that series already accepted.
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> index 2d5d89475b76..623254786c2d 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> @@ -37,10 +37,14 @@
>  		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
>  		enable-active-high;
>  	};
>  };
>  
> +&A53_0 {
> +	cpu-supply = <&buck2_reg>;
> +};
> +
>  &fec1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_fec1>;
>  	phy-mode = "rgmii-id";
>  	phy-handle = <&ethphy0>;
> @@ -93,10 +97,124 @@
>  	pinctrl-0 = <&pinctrl_wdog>;
>  	fsl,ext-reset-output;
>  	status = "okay";
>  };
>  
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	pmic@4b {
> +		compatible = "rohm,bd71847";
> +		reg = <0x4b>;
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <3 GPIO_ACTIVE_LOW>;
> +		rohm,reset-snvs-powered;
> +
> +		regulators {
> +			buck1_reg: BUCK1 {
> +				regulator-compatible = "BUCK1";

bindings/regulator/regulator.txt says that regulator-compatible is a
deprecated property.

Shawn

> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <1250>;
> +			};
> +
> +			buck2_reg: BUCK2 {
> +				regulator-compatible = "BUCK2";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <1250>;
> +				rohm,dvs-run-voltage = <1000000>;
> +				rohm,dvs-idle-voltage = <900000>;
> +			};
> +
> +			buck3_reg: BUCK3 {
> +				// BUCK5 in datasheet
> +				regulator-compatible = "BUCK3";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck4_reg: BUCK4 {
> +				// BUCK6 in datasheet
> +				regulator-compatible = "BUCK4";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck5_reg: BUCK5 {
> +				// BUCK7 in datasheet
> +				regulator-compatible = "BUCK5";
> +				regulator-min-microvolt = <1605000>;
> +				regulator-max-microvolt = <1995000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck6_reg: BUCK6 {
> +				// BUCK8 in datasheet
> +				regulator-compatible = "BUCK6";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo1_reg: LDO1 {
> +				regulator-compatible = "LDO1";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo2_reg: LDO2 {
> +				regulator-compatible = "LDO2";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo3_reg: LDO3 {
> +				regulator-compatible = "LDO3";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo4_reg: LDO4 {
> +				regulator-compatible = "LDO4";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo6_reg: LDO6 {
> +				regulator-compatible = "LDO6";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
>  &iomuxc {
>  	pinctrl-names = "default";
>  
>  	pinctrl_fec1: fec1grp {
>  		fsl,pins = <
> @@ -122,10 +240,23 @@
>  		fsl,pins = <
>  			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x19
>  		>;
>  	};
>  
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
> +			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicirq {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
> +		>;
> +	};
> +
>  	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
>  		fsl,pins = <
>  			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
>  		>;
>  	};
> -- 
> 2.17.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel