From: Guenter Roeck <linux@roeck-us.net>
To: Serge Semin <fancer.lancer@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Serge Semin <Sergey.Semin@t-platforms.ru>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 1/2] net: phy: realtek: Add rtl8211e rx/tx delays config
Date: Sun, 12 May 2019 22:41:32 -0700 [thread overview]
Message-ID: <20190513054132.GA7563@roeck-us.net> (raw)
In-Reply-To: <20190426212112.5624-1-fancer.lancer@gmail.com>
Hi,
On Sat, Apr 27, 2019 at 12:21:11AM +0300, Serge Semin wrote:
> There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
> delays to TXC and RXC for TXD/RXD latching. Alas this is the only
> documented info regarding the RGMII timing control configurations the PHY
> provides. It turns out the same settings can be setup via MDIO registers
> hidden in the extension pages layout. Particularly the extension page 0xa4
> provides a register 0x1c, which bits 1 and 2 control the described delays.
> They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
>
> The hidden RGMII configs register utilization was found in the rtl8211e
> U-boot driver:
> https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
>
> There is also a freebsd-folks discussion regarding this register:
> https://reviews.freebsd.org/D13591
>
> It confirms that the register bits field must control the so called
> configuration pins described in the table 12-13 of the official PHY
> datasheet:
> 8:6 = PHY Address
> 5:4 = Auto-Negotiation
> 3 = Interface Mode Select
> 2 = RX Delay
> 1 = TX Delay
> 0 = SELRGV
>
> Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
This patch results in a crash when running arm:ast2500-evb in qemu.
[ 4.894572] [00000000] *pgd=00000000
[ 4.895329] Internal error: Oops: 80000005 [#1] ARM
[ 4.896066] CPU: 0 PID: 1 Comm: swapper Not tainted 5.1.0-09698-g1fb3b52 #1
[ 4.896364] Hardware name: Generic DT based system
[ 4.896823] PC is at 0x0
[ 4.897037] LR is at phy_select_page+0x3c/0x7c
Debugging shows that phydev->drv->write_page and phydev->drv->read_page
are NULL, so the crash isn't entirely surprising.
What I don't understand is how this can work in the first place.
The modified entry in realtek_drvs[] doesn't have read_page/write_page
functions defined, yet rtl8211e_config_init() depends on it.
What am I missing here ?
Thanks,
Guenter
next prev parent reply other threads:[~2019-05-13 5:41 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-26 9:30 [PATCH] net: phy: realtek: Add rtl8211e rx/tx delays config Serge Semin
2019-04-26 13:28 ` Andrew Lunn
2019-04-26 19:19 ` Serge Semin
2019-04-26 20:05 ` Andrew Lunn
2019-04-26 20:28 ` Serge Semin
2019-04-26 17:17 ` Heiner Kallweit
2019-04-26 20:26 ` Serge Semin
2019-04-26 21:21 ` [PATCH v2 1/2] " Serge Semin
2019-04-26 21:40 ` Andrew Lunn
2019-04-26 23:45 ` Serge Semin
2019-04-27 3:11 ` Florian Fainelli
2019-04-27 7:44 ` Serge Semin
2019-04-27 15:21 ` Andrew Lunn
2019-04-28 19:19 ` Serge Semin
2019-04-27 19:20 ` Florian Fainelli
2019-05-08 1:29 ` [PATCH v3 0/2] net: phy: realtek: Fix RGMII TX/RX-delays initial config of rtl8211(e|f) Serge Semin
2019-05-08 1:29 ` [PATCH v3 1/2] net: phy: realtek: Add rtl8211e rx/tx delays config Serge Semin
2019-05-08 1:29 ` [PATCH v3 2/2] net: phy: realtek: Change TX-delay setting for RGMII modes only Serge Semin
2019-05-08 16:37 ` [PATCH v3 0/2] net: phy: realtek: Fix RGMII TX/RX-delays initial config of rtl8211(e|f) David Miller
2019-05-08 21:51 ` [PATCH v4 " Serge Semin
2019-05-08 21:51 ` [PATCH v4 1/2] net: phy: realtek: Add rtl8211e rx/tx delays config Serge Semin
2019-05-08 21:51 ` [PATCH v4 2/2] net: phy: realtek: Change TX-delay setting for RGMII modes only Serge Semin
2019-05-08 23:31 ` [PATCH v4 0/2] net: phy: realtek: Fix RGMII TX/RX-delays initial config of rtl8211(e|f) David Miller
2019-05-13 5:41 ` Guenter Roeck [this message]
2019-05-13 10:37 ` [PATCH v2 1/2] net: phy: realtek: Add rtl8211e rx/tx delays config Serge Semin
2019-04-26 21:21 ` [PATCH v2 2/2] net: phy: realtek: Change TX-delay setting for RGMII modes only Serge Semin
2019-04-26 21:46 ` Andrew Lunn
2019-04-26 23:35 ` Serge Semin
2019-04-29 17:37 ` Florian Fainelli
2019-04-29 18:29 ` Vladimir Oltean
2019-04-29 21:12 ` Serge Semin
2019-04-29 22:36 ` Vladimir Oltean
2019-04-30 12:54 ` Serge Semin
2019-04-30 20:44 ` Martin Blumenstingl
2019-05-08 0:48 ` Serge Semin
2019-04-30 21:16 ` Martin Blumenstingl
2019-05-01 23:03 ` Vladimir Oltean
2019-05-03 17:29 ` Martin Blumenstingl
2019-05-06 14:39 ` Serge Semin
2019-05-06 17:21 ` Martin Blumenstingl
2019-05-07 17:37 ` Heiner Kallweit
2019-05-07 20:09 ` Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190513054132.GA7563@roeck-us.net \
--to=linux@roeck-us.net \
--cc=Sergey.Semin@t-platforms.ru \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=fancer.lancer@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.