All of lore.kernel.org
 help / color / mirror / Atom feed
From: Lukasz Majewski <lukma@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] imx: Select the pinctrl drivers when DM is used
Date: Wed, 5 Jun 2019 15:48:07 +0200	[thread overview]
Message-ID: <20190605154807.59540271@jawa> (raw)
In-Reply-To: <20190524150222.4586ab06@jawa>

Hi Fabio,

> On Fri, 24 May 2019 09:50:53 -0300
> Fabio Estevam <festevam@gmail.com> wrote:
> 
> > When using device model it is required to select the pinctrl
> > drivers so that the pins can be properly configured via
> > devicetree.
> > 
> > mx6sabreauto board is an example of a target that uses DM and does
> > not select the pinctrl drivers.
> > 
> > Instead of doing the pinctrl driver selection in each individual
> > defconfig file, select it at SoC level when DM is used. 
> > 
> > Signed-off-by: Fabio Estevam <festevam@gmail.com>
> > ---
> >  arch/arm/Kconfig | 8 ++++++++
> >  1 file changed, 8 insertions(+)
> > 
> > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> > index efb9aab390..4c361c9a1d 100644
> > --- a/arch/arm/Kconfig
> > +++ b/arch/arm/Kconfig
> > @@ -787,6 +787,8 @@ config ARCH_MX31
> >  config ARCH_MX7ULP
> >  	bool "NXP MX7ULP"
> >  	select CPU_V7A
> > +	select PINCTRL if DM
> > +	select PINCTRL_IMX7ULP if DM
> >  	select ROM_UNIFIED_SECTIONS
> >  	imply MXC_GPIO
> >  
> > @@ -795,6 +797,8 @@ config ARCH_MX7
> >  	select ARCH_MISC_INIT
> >  	select BOARD_EARLY_INIT_F
> >  	select CPU_V7A
> > +	select PINCTRL if DM
> > +	select PINCTRL_IMX7 if DM
> >  	select SYS_FSL_HAS_SEC if SECURE_BOOT
> >  	select SYS_FSL_SEC_COMPAT_4
> >  	select SYS_FSL_SEC_LE
> > @@ -803,6 +807,8 @@ config ARCH_MX7
> >  config ARCH_MX6
> >  	bool "Freescale MX6"
> >  	select CPU_V7A
> > +	select PINCTRL if DM
> > +	select PINCTRL_IMX6 if DM
> >  	select SYS_FSL_HAS_SEC if SECURE_BOOT
> >  	select SYS_FSL_SEC_COMPAT_4
> >  	select SYS_FSL_SEC_LE
> > @@ -818,6 +824,8 @@ config ARCH_MX5
> >  	bool "Freescale MX5"
> >  	select BOARD_EARLY_INIT_F
> >  	select CPU_V7A
> > +	select PINCTRL if DM
> > +	select PINCTRL_IMX5 if DM
> >  	imply MXC_GPIO
> >  
> >  config ARCH_OWL  
> 
> Reviewed-by: Lukasz Majewski <lukma@denx.de>
> 

Unfortunately, after some testing it turned out that this patch causes
build break for "display5_factory_defconfig"

The build break is as follows:


WARNING: unmet direct dependencies detected for PINCTRL_IMX6
  Depends on [n]: ARCH_MX6 [=y] && PINCTRL_FULL [=n]
  Selected by [y]:
  - ARCH_MX6 [=y] && <choice> && DM [=y]

WARNING: unmet direct dependencies detected for PINCTRL_IMX6
  Depends on [n]: ARCH_MX6 [=y] && PINCTRL_FULL [=n]
  Selected by [y]:
  - ARCH_MX6 [=y] && <choice> && DM [=y]
../drivers/pinctrl/nxp/pinctrl-imx6.c:32:32:
warning: ?imx6_pinctrl_match? defined but not used
[-Wunused-const-variable=] static const struct udevice_id
imx6_pinctrl_match[] = { ^~~~~~~~~~~~~~~~~~ drivers/built-in.o: In
function `imx6_pinctrl_probe':
build/../drivers/pinctrl/nxp/pinctrl-imx6.c:29: undefined reference to
`imx_pinctrl_probe'
drivers/built-in.o:(.u_boot_list_2_driver_2_imx6_pinctrl+0x14):
undefined reference to `imx_pinctrl_remove'
drivers/built-in.o:(.u_boot_list_2_driver_2_imx6_pinctrl+0x3c):
undefined reference to `imx_pinctrl_ops' arm-linux-gnueabihf-ld.bfd:
BFD (Linaro_Binutils-2017.05) 2.27.0.20161019 assertion
fail /home/tcwg-buildslave/workspace/tcwg-make-release/builder_arch/amd64/label/tcwg-x86_64-build/target/arm-linux-gnueabihf/snapshots/binutils-gdb.git~linaro-local~linaro_binutils-2_27-branch/bfd/elf32-arm.c:8784



> 
> Best regards,
> 
> Lukasz Majewski
> 
> --
> 
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma at denx.de




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190605/31794b5e/attachment.sig>

  reply	other threads:[~2019-06-05 13:48 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-24 12:50 [U-Boot] [PATCH] imx: Select the pinctrl drivers when DM is used Fabio Estevam
2019-05-24 13:02 ` Lukasz Majewski
2019-06-05 13:48   ` Lukasz Majewski [this message]
2019-06-04 20:08 ` Sjoerd Simons

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190605154807.59540271@jawa \
    --to=lukma@denx.de \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.