* [patch 0/5] *** Cover Letter: patch submission for AST2500 UART driver *** @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Hi, The below mentioned patches are for AST2500 UART driver. AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. Thanks and Regards Sudheer.V sudheer veliseti (5): AST2500 DMA UART driver build configuration for AST2500 DMA UART driver DT nodes for AST2500 DMA UART driver defconfig and MAINTAINERS updated for AST2500 DMA UART driver Documentation: DT bindings AST2500 DMA UART driver .../bindings/serial/ast2500-dma-uart.txt | 40 + MAINTAINERS | 13 + arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 + arch/arm/boot/dts/aspeed-g5.dtsi | 71 +- arch/arm/configs/aspeed_g5_defconfig | 1 + .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ drivers/tty/serial/8250/Kconfig | 35 +- drivers/tty/serial/8250/Makefile | 1 + 8 files changed, 2105 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c -- 2.17.1 ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 0/5] *** Cover Letter: patch submission for AST2500 UART driver *** @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Hi, The below mentioned patches are for AST2500 UART driver. AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. Thanks and Regards Sudheer.V sudheer veliseti (5): AST2500 DMA UART driver build configuration for AST2500 DMA UART driver DT nodes for AST2500 DMA UART driver defconfig and MAINTAINERS updated for AST2500 DMA UART driver Documentation: DT bindings AST2500 DMA UART driver .../bindings/serial/ast2500-dma-uart.txt | 40 + MAINTAINERS | 13 + arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 + arch/arm/boot/dts/aspeed-g5.dtsi | 71 +- arch/arm/configs/aspeed_g5_defconfig | 1 + .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ drivers/tty/serial/8250/Kconfig | 35 +- drivers/tty/serial/8250/Makefile | 1 + 8 files changed, 2105 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 0/5] *** Cover Letter: patch submission for AST2500 UART driver *** @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Hi, The below mentioned patches are for AST2500 UART driver. AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. Thanks and Regards Sudheer.V sudheer veliseti (5): AST2500 DMA UART driver build configuration for AST2500 DMA UART driver DT nodes for AST2500 DMA UART driver defconfig and MAINTAINERS updated for AST2500 DMA UART driver Documentation: DT bindings AST2500 DMA UART driver .../bindings/serial/ast2500-dma-uart.txt | 40 + MAINTAINERS | 13 + arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 + arch/arm/boot/dts/aspeed-g5.dtsi | 71 +- arch/arm/configs/aspeed_g5_defconfig | 1 + .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ drivers/tty/serial/8250/Kconfig | 35 +- drivers/tty/serial/8250/Makefile | 1 + 8 files changed, 2105 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c -- 2.17.1 ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-05 12:23 ` sudheer.v -1 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ 1 file changed, 1928 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c diff --git a/drivers/tty/serial/8250/8250_ast2500_uart_dma.c b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c new file mode 100644 index 000000000000..6f3adcac9190 --- /dev/null +++ b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c @@ -0,0 +1,1928 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DMA UART Driver for ASPEED BMC chip: AST2500 + * + * Copyright (C) 2019 sudheer Kumar veliseti, Aspeed technology Inc. + * <open.sudheer@gmail.com> + * + */ +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/mutex.h> +#include <linux/nmi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#include "8250.h" + +#define DMA_BUFF_SIZE 0x1000 // 4096 +#define SDMA_RX_BUFF_SIZE 0x10000 // 65536 + +#define SDDMA_RX_FIX 1 +/* enum ast_uart_chan_op + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state + */ + +enum ast_uart_chan_op { + AST_UART_DMAOP_TRIGGER, + AST_UART_DMAOP_STOP, + AST_UART_DMAOP_PAUSE, +}; + +/* ast_uart_dma_cbfn_t * * buffer callback routine type */ +typedef void (*ast_uart_dma_cbfn_t)(void *dev_id, u16 len); + +struct ast_sdma_info { + u8 ch_no; + u8 direction; + u8 enable; + void *priv; + char *sdma_virt_addr; + dma_addr_t dma_phy_addr; + /* cdriver callbacks */ + ast_uart_dma_cbfn_t callback_fn; /* buffer done callback */ +}; + +#define AST_UART_SDMA_CH 12 + +struct ast_sdma_ch { + struct ast_sdma_info tx_dma_info[AST_UART_SDMA_CH]; + struct ast_sdma_info rx_dma_info[AST_UART_SDMA_CH]; +}; + +struct ast_sdma { + void __iomem *reg_base; + int dma_irq; + struct ast_sdma_ch *dma_ch; + struct regmap *map; +}; + + + +#define UART_TX_SDMA_EN 0x00 +#define UART_RX_SDMA_EN 0x04 +#define UART_SDMA_CONF 0x08 +#define UART_SDMA_TIMER 0x0C +#define UART_TX_SDMA_REST 0x20 +#define UART_RX_SDMA_REST 0x24 +#define UART_TX_SDMA_IER 0x30 +#define UART_TX_SDMA_ISR 0x34 +#define UART_RX_SDMA_IER 0x38 +#define UART_RX_SDMA_ISR 0x3C +#define UART_TX_R_POINT(x) (0x40 + (x * 0x20)) +#define UART_TX_W_POINT(x) (0x44 + (x * 0x20)) +#define UART_TX_SDMA_ADDR(x) (0x48 + (x * 0x20)) +#define UART_RX_R_POINT(x) (0x50 + (x * 0x20)) +#define UART_RX_W_POINT(x) (0x54 + (x * 0x20)) +#define UART_RX_SDMA_ADDR(x) (0x58 + (x * 0x20)) + +/* UART_TX_SDMA_EN-0x00 : UART TX DMA Enable */ +/* UART_RX_SDMA_EN-0x04 : UART RX DMA Enable */ +#define SDMA_CH_EN(x) (0x1 << (x)) + +/* UART_SDMA_CONF - 0x08 : Misc, Buffer size */ +#define SDMA_TX_BUFF_SIZE_MASK (0x3) +#define SDMA_SET_TX_BUFF_SIZE(x) (x) +#define SDMA_BUFF_SIZE_1KB (0x0) +#define SDMA_BUFF_SIZE_4KB (0x1) +#define SDMA_BUFF_SIZE_16KB (0x2) +#define SDMA_BUFF_SIZE_64KB (0x3) +#define SDMA_RX_BUFF_SIZE_MASK (0x3 << 2) +#define SDMA_SET_RX_BUFF_SIZE(x) (x << 2) +#define SDMA_TIMEOUT_DIS (0x1 << 4) + +/* UART_SDMA_TIMER-0x0C : UART DMA time out timer */ + +/* UART_TX_SDMA_IER 0x30 */ +/* UART_TX_SDMA_ISR 0x34 */ + +#define UART_SDMA11_INT (1 << 11) +#define UART_SDMA10_INT (1 << 10) +#define UART_SDMA9_INT (1 << 9) +#define UART_SDMA8_INT (1 << 8) +#define UART_SDMA7_INT (1 << 7) +#define UART_SDMA6_INT (1 << 6) +#define UART_SDMA5_INT (1 << 5) +#define UART_SDMA4_INT (1 << 4) +#define UART_SDMA3_INT (1 << 3) +#define UART_SDMA2_INT (1 << 2) +#define UART_SDMA1_INT (1 << 1) +#define UART_SDMA0_INT (1 << 0) + + +#define CONFIG_UART_DMA_DEBUG + +#ifdef CONFIG_UART_DMA_DEBUG +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define UART_DBG(fmt, args...) +#endif + +#define CONFIG_UART_TX_DMA_DEBUG 1 + +#ifdef CONFIG_UART_TX_DMA_DEBUG +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) +#else +#define UART_TX_DBG(fmt, args...) +#endif + +/* + * Configuration: + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option + * is unsafe when used on edge-triggered interrupts. + */ +static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; + +static unsigned int nr_uarts = CONFIG_AST_RUNTIME_DMA_UARTS; + +/* + * Debugging. + */ +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_AUTOCONF(fmt...) UART_DBG(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) \ + do { \ + } while (0) +#endif + +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_INTR(fmt...) UART_DBG(fmt) +#else +#define DEBUG_INTR(fmt...) \ + do { \ + } while (0) +#endif + +#define PASS_LIMIT 256 + +#include <asm/serial.h> + +#define UART_DMA_NR CONFIG_AST_NR_DMA_UARTS + + + +struct ast_uart_priv_data { + + unsigned short line; //index of uart port + struct uart_8250_port *up; + u8 dma_ch; // dma channel number + struct circ_buf rx_dma_buf; + struct circ_buf tx_dma_buf; + dma_addr_t dma_rx_addr; /* Mapped ADMA descr. table */ + dma_addr_t dma_tx_addr; /* Mapped ADMA descr. table */ +#ifdef SDDMA_RX_FIX + struct tasklet_struct rx_tasklet; +#else + struct timer_list rx_timer; +#endif + struct tasklet_struct tx_tasklet; + spinlock_t lock; + int tx_done; + int tx_count; +}; + + +static inline struct uart_8250_port * +to_uart_8250_port(struct uart_port *uart) { + return container_of(uart, struct uart_8250_port, port); +} + +struct irq_info { + spinlock_t lock; + struct uart_8250_port *up; +}; + +static struct irq_info ast_uart_irq[1]; +static DEFINE_MUTEX(ast_uart_mutex); + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 + | UART_FCR_DMA_SELECT, + .flags = UART_CAP_FIFO, + }, +}; + +/* sane hardware needs no mapping */ +#define map_8250_in_reg(up, offset) (offset) +#define map_8250_out_reg(up, offset) (offset) + +// SDMA - software Layer : ast-uart-sdma.c + +#define AST_UART_SDMA_DEBUG 1 + +#ifdef AST_UART_SDMA_DEBUG +#define SDMADBUG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define SDMADBUG(fmt, args...) +#endif + +static inline void ast_uart_sdma_write(struct ast_sdma *sdma, + u32 val, u32 reg) +{ + // SDMADBUG("uart dma write : val: %x , reg : %x\n",val,reg); + writel(val, sdma->reg_base + reg); +} + +static inline u32 ast_uart_sdma_read(struct ast_sdma *sdma, u32 reg) +{ + return readl(sdma->reg_base + reg); +} + +struct ast_sdma ast_uart_sdma; + +int ast_uart_rx_sdma_enqueue(u8 ch, dma_addr_t rx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, rx buff = %x\n", ch, rx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, rx_buff, UART_RX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_tx_sdma_enqueue(u8 ch, dma_addr_t tx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, tx buff = %x\n", ch, tx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, tx_buff, UART_TX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("Trigger\n"); + dma_ch->enable = 1; +#ifdef SDDMA_RX_FIX +#else + ast_uart_set_sdma_time_out(0xffff); +#endif + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) | (0x1 << ch), + UART_RX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + // disable engine + SDMADBUG("STOP\n"); + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) | + (0x1 << ch), + UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) & + ~(0x1 << ch), + UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(ch)); + ast_uart_sdma_write(sdma, dma_ch->dma_phy_addr, UART_RX_SDMA_ADDR(ch)); + break; + case AST_UART_DMAOP_PAUSE: + // disable engine + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + break; + } + + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("TRIGGER : Enable\n"); + dma_ch->enable = 1; + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) | (0x1 << ch), + UART_TX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + SDMADBUG("STOP : DISABLE & RESET\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) | + (0x1 << ch), + UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) & + ~(0x1 << ch), + UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(ch)); + break; + case AST_UART_DMAOP_PAUSE: + SDMADBUG("PAUSE : DISABLE\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + } + + local_irq_restore(flags); + return 0; +} + +u32 ast_uart_get_tx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_TX_R_POINT(ch)); +} + +int ast_uart_tx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("TX DMA CTRL [ch %d] point %d\n", ch, point); + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_TX_W_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_IER) | (1 << ch), + UART_TX_SDMA_IER); + + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("RX DMA CTRL [ch %d] point %x\n", ch, point); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_RX_R_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +#ifdef SDDMA_RX_FIX +char *ast_uart_rx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return 0; + } + dma_ch->priv = id; + + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_IER) | (1 << ch), + UART_RX_SDMA_IER); + + local_irq_restore(flags); + + return dma_ch->sdma_virt_addr; +} + +#else +char *ast_uart_rx_sdma_request(u8 ch, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + + local_irq_restore(flags); + return dma_ch->sdma_virt_addr; +} +#endif + +u16 ast_uart_get_rx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_RX_W_POINT(ch)); +} + +void ast_uart_set_sdma_time_out(u16 val) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + ast_uart_sdma_write(sdma, val, UART_SDMA_TIMER); +} + +static inline void ast_sdma_bufffdone(struct ast_sdma_info *sdma_ch) +{ + u32 len; + struct ast_sdma *sdma = &ast_uart_sdma; + + if (sdma_ch->enable == 0) { + SDMADBUG("sdma Please check ch_no %x %s!!!!!\n", + sdma_ch->ch_no, sdma_ch->direction ? "TX" : "RX"); + if (sdma_ch->direction) { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) + & ~(0x1 << sdma_ch->ch_no), UART_TX_SDMA_EN); + } else { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << sdma_ch->ch_no), UART_RX_SDMA_EN); + ast_uart_rx_sdma_update(sdma_ch->ch_no, + ast_uart_get_rx_sdma_pt(sdma_ch->ch_no)); + SDMADBUG("OFFSET : UART_RX_SDMA_EN = %x\n ", + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN)); + } + return; + } + + if (sdma_ch->direction) { + len = ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)); + SDMADBUG("tx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_TX_W_POINT(sdma_ch->ch_no)) + ); + } else { + SDMADBUG("rx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_RX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)) + ); + len = ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)); + } + + SDMADBUG("<dma dwn>: ch[%d] : %s ,len : %d\n", sdma_ch->ch_no, + sdma_ch->direction ? "tx" : "rx", len); + + if (sdma_ch->callback_fn != NULL) + (sdma_ch->callback_fn)(sdma_ch->priv, len); +} + +static irqreturn_t ast_uart_sdma_irq(int irq, void *dev_id) +{ + struct ast_sdma *sdma = (struct ast_sdma *)dev_id; + + u32 tx_sts = ast_uart_sdma_read(sdma, UART_TX_SDMA_ISR); + u32 rx_sts = ast_uart_sdma_read(sdma, UART_RX_SDMA_ISR); + + SDMADBUG("tx sts : %x, rx sts : %x\n", tx_sts, rx_sts); + + if ((tx_sts == 0) && (rx_sts == 0)) { + SDMADBUG("SDMA IRQ ERROR !!!\n"); + return IRQ_HANDLED; + } + + if (rx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[0])); + } else if (rx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[1])); + } else if (rx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[2])); + } else if (rx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[3])); + } else if (rx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[4])); + } else if (rx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[5])); + } else if (rx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[6])); + } else if (rx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[7])); + } else if (rx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[8])); + } else if (rx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[9])); + } else if (rx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[10])); + } else if (rx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[11])); + } else { + + } + + if (tx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[0])); + } else if (tx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[1])); + } else if (tx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[2])); + } else if (tx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[3])); + } else if (tx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[4])); + } else if (tx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[5])); + } else if (tx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[6])); + } else if (tx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[7])); + } else if (tx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[8])); + } else if (tx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[9])); + } else if (tx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[10])); + } else if (tx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[11])); + } else { + } + + return IRQ_HANDLED; +} + +static int ast_uart_sdma_probe(void) +{ + int i; + struct device_node *node; + int ret; + struct ast_sdma *sdma = &ast_uart_sdma; + char *rx_dma_virt_addr; + dma_addr_t rx_dma_phy_addr; + + sdma->dma_ch = kzalloc(sizeof(struct ast_sdma_ch), GFP_KERNEL); + if (!sdma->dma_ch) + return -ENOMEM; + + // sdma memory mapping + node = of_find_compatible_node(NULL, NULL, "aspeed,ast-uart-sdma"); + if (!node) + return -ENODEV; + + sdma->reg_base = of_iomap(node, 0); + if (IS_ERR(sdma->reg_base)) + return PTR_ERR(sdma->map); + rx_dma_virt_addr = dma_alloc_coherent(NULL, + SDMA_RX_BUFF_SIZE * AST_UART_SDMA_CH, &rx_dma_phy_addr, GFP_KERNEL); + + if (!rx_dma_virt_addr) + SDMADBUG(" rx_dma_virt_addr Errr : unable top alloc\n"); + + for (i = 0; i < AST_UART_SDMA_CH; i++) { + // TX ------------------------ + sdma->dma_ch->tx_dma_info[i].enable = 0; + sdma->dma_ch->tx_dma_info[i].ch_no = i; + sdma->dma_ch->tx_dma_info[i].direction = 1; + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(i)); + // RX ------------------------ + sdma->dma_ch->rx_dma_info[i].enable = 0; + sdma->dma_ch->rx_dma_info[i].ch_no = i; + sdma->dma_ch->rx_dma_info[i].direction = 0; + sdma->dma_ch->rx_dma_info[i].sdma_virt_addr = + rx_dma_virt_addr + (SDMA_RX_BUFF_SIZE * i); + sdma->dma_ch->rx_dma_info[i].dma_phy_addr = + rx_dma_phy_addr + (SDMA_RX_BUFF_SIZE * i); + ast_uart_sdma_write(sdma, + sdma->dma_ch->rx_dma_info[i].dma_phy_addr, + UART_RX_SDMA_ADDR(i)); + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(i)); + } + + ast_uart_sdma_write(sdma, 0xffffffff, UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0xffffffff, UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_EN); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_EN); + +#ifdef SDDMA_RX_FIX + ast_uart_sdma_write(sdma, 0x200, UART_SDMA_TIMER); +#else + ast_uart_sdma_write(sdma, 0xffff, UART_SDMA_TIMER); +#endif + + // TX + ast_uart_sdma_write(sdma, 0xfff, UART_TX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_IER); + + // RX + ast_uart_sdma_write(sdma, 0xfff, UART_RX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_IER); + + sdma->dma_irq = of_irq_get(node, 0); + ret = request_irq(sdma->dma_irq, ast_uart_sdma_irq, 0, + "sdma-intr", sdma); + if (ret) { + SDMADBUG("Unable to get UART SDMA IRQ %x\n", ret); + return -ENODEV; + } + + ast_uart_sdma_write(sdma, SDMA_SET_TX_BUFF_SIZE(SDMA_BUFF_SIZE_4KB) | + SDMA_SET_RX_BUFF_SIZE(SDMA_BUFF_SIZE_64KB), + UART_SDMA_CONF); + return 0; +} + +// END of SDMA Layer + +// UART Driver Layer + +static unsigned int ast_serial_in(struct uart_8250_port *up, int offset) +{ + offset = map_8250_in_reg(up, offset) << up->port.regshift; + return readb(up->port.membase + offset); +} + +static void ast_serial_out(struct uart_8250_port *up, int offset, int value) +{ + /* Save the offset before it's remapped */ + offset = map_8250_out_reg(up, offset) << up->port.regshift; + writeb(value, up->port.membase + offset); +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) ast_serial_in(up, offset) +#define serial_outp(up, offset, value) ast_serial_out(up, offset, value) + +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) + +static void ast_uart_tx_sdma_tasklet_func(unsigned long data) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit = NULL; + u32 tx_pt; + + + if (!up) + return; + xmit = &up->port.state->xmit; + spin_lock(&up->port.lock); + priv->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); + dma_sync_single_for_device(up->port.dev, priv->dma_tx_addr, + UART_XMIT_SIZE, DMA_TO_DEVICE); + tx_pt = ast_uart_get_tx_sdma_pt(priv->dma_ch); + + if (tx_pt > xmit->head) { + if ((tx_pt & 0xfffc) == 0) + ast_uart_tx_sdma_update(priv->dma_ch, 0xffff); + else + ast_uart_tx_sdma_update(priv->dma_ch, 0); + } else { + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + } + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + spin_unlock(&up->port.lock); +} + +static void ast_uart_tx_buffdone(void *dev_id, u16 len) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit; + + if (!up) + return; + xmit = &(up->port.state->xmit); + + UART_TX_DBG("line[%d] : tx len = % d\n", priv->line, len); + spin_lock(&up->port.lock); + xmit->tail = len; + UART_TX_DBG(" line[%d], xmit->head = %d, xmit->tail = % d\n", + priv->line, xmit->head, xmit->tail); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (xmit->head != xmit->tail) + tasklet_schedule(&priv->tx_tasklet); + + spin_unlock(&up->port.lock); +} + +#ifdef SDDMA_RX_FIX +static void ast_uart_rx_sdma_tasklet_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct tty_port *ttyport; + int count; + int copy = 0; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + + ttyport = &up->port.state->port; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + spin_lock(&up->port.lock); + if (rx_ring->head > rx_ring->tail) { + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + if (count) { + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + up->port.icount.rx += count; + tty_flip_buffer_push(ttyport); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + } + spin_unlock(&up->port.lock); +} + +static void ast_uart_rx_buffdone(void *dev_id, u16 len) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + UART_DBG("line[%d], head = %d,len:%d\n", + priv->line, priv->rx_dma_buf.head, len); + spin_lock(&up->port.lock); + rx_ring->head = len; + spin_unlock(&up->port.lock); + tasklet_schedule(&priv->rx_tasklet); +} + +#else +static void ast_uart_rx_timer_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct tty_port *ttyport; + struct circ_buf *rx_ring; + struct tty_struct *tty; + char flag; + int count; + int copy; + + + if (!up) + return; + ttyport = &up->port.state->port; + rx_ring = &up->rx_dma_buf; + tty = up->port.state->port.tty; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + rx_ring->head = ast_uart_get_rx_sdma_pt(priv->dma_ch); + del_timer(&up->rx_timer); + + if (rx_ring->head > rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + // UART_DBG("@@--%s-- ch = 0x%x\n", __func__, ch); + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + + if (count) { + //UART_DBG("\n count = % d\n", count); + up->port.icount.rx += count; + spin_lock(&up->port.lock); + tty_flip_buffer_push(ttyport); + spin_unlock(&up->port.lock); + //UART_DBG("update rx_ring->tail % x\n", rx_ring->tail); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + priv->workaround = 1; + } else { + if (priv->workaround) { + priv->workaround++; + if (priv->workaround > 1) + ast_uart_set_sdma_time_out(0); + else + ast_uart_set_sdma_time_out(0xffff); + } + } + add_timer(&up->rx_timer); +} +#endif + +/* + * FIFO support. + */ +static inline void ast25xx_uart_clear_fifos(struct uart_8250_port *p) +{ + serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(p, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(p, UART_FCR, 0); +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned long flags; + + UART_DBG("line[%d]\n", up->port.line); + if (!up->port.iobase && !up->port.mapbase && !up->port.membase) + return; + + DEBUG_AUTOCONF("ttyDMA%d : autoconf (0x%04lx, 0x%p) : ", up->port.line, + up->port.iobase, up->port.membase); + + spin_lock_irqsave(&up->port.lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + + if (up->port.type == PORT_UNKNOWN) + goto out; + + /* + * Reset the UART. + */ + ast25xx_uart_clear_fifos(up); + ast_serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); + DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name); +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + ast_serial_out(p, UART_IER, p->ier); + } +} + +static void ast25xx_uart_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_TX_DBG("line[%d]\n", up->port.line); + __stop_tx(up); +} + +static void transmit_chars(struct uart_8250_port *up); + +static void ast25xx_uart_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + + UART_TX_DBG("line[%d]\n", port->line); + tasklet_schedule(&priv->tx_tasklet); +} + +static void ast25xx_uart_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + ast_serial_out(up, UART_IER, up->ier); +} + +static void ast25xx_uart_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier |= UART_IER_MSI; + ast_serial_out(up, UART_IER, up->ier); +} + +static void transmit_chars(struct uart_8250_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + ast25xx_uart_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + ast_serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static unsigned int check_modem_status(struct uart_8250_port *up) +{ + unsigned int status = ast_serial_in(up, UART_MSR); + + UART_DBG("line[%d]\n", up->port.line); + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI + && up->port.state != NULL) { + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, + status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, + status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); + } + + return status; +} + +/* + * This handles the interrupt from one port. + */ +static inline void ast25xx_uart_handle_port(struct uart_8250_port *up) +{ + unsigned int status; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + status = serial_inp(up, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * This is the serial driver's interrupt routine. + */ +static irqreturn_t ast_uart_interrupt(int irq, void *dev_id) +{ + struct irq_info *i = dev_id; + int pass_counter = 0, handled = 0, end = 0; + + DEBUG_INTR("(%d) ", irq); + spin_lock(&i->lock); + + do { + struct uart_8250_port *up; + unsigned int iir; + + up = (struct uart_8250_port *)(i->up); + + iir = ast_serial_in(up, UART_IIR); + if (!(iir & UART_IIR_NO_INT)) { + ast25xx_uart_handle_port(up); + handled = 1; + + } else + end = 1; + + if (pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + UART_DBG(KERN_ERR + "ast-uart-dma:too much work for irq%d\n", irq); + break; + } + } while (end); + + spin_unlock(&i->lock); + + DEBUG_INTR("end.\n"); + + return IRQ_RETVAL(handled); +} + +static unsigned int ast25xx_uart_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + unsigned int lsr; + + UART_TX_DBG("line[%d]\n", up->port.line); + + spin_lock_irqsave(&up->port.lock, flags); + lsr = ast_serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&up->port.lock, flags); + + return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0; +} + +static unsigned int ast25xx_uart_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned int status; + unsigned int ret; + + status = check_modem_status(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void ast25xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char mcr = 0; + + mctrl = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + ast_serial_out(up, UART_MCR, mcr); + +} + +static void ast25xx_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + ast_serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ast25xx_uart_startup(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + // TX DMA + struct circ_buf *xmit = &up->port.state->xmit; + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + unsigned char lsr, iir; + int retval; + int irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; + + UART_DBG("%s\n", __func__); + + priv->up = up; + + UART_DBG("line[%d]\n", port->line); + up->capabilities = uart_config[up->port.type].flags; + up->mcr = 0; + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + ast25xx_uart_clear_fifos(up); + /* + * Clear the interrupt registers. + */ + (void)serial_inp(up, UART_LSR); + (void)serial_inp(up, UART_RX); + (void)serial_inp(up, UART_IIR); + (void)serial_inp(up, UART_MSR); + + ast_uart_irq[0].up = up; + retval = request_irq(up->port.irq, ast_uart_interrupt, irq_flags, + "ast-uart-dma", ast_uart_irq); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl |= TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_outp(up, UART_IER, UART_IER_THRI); + lsr = ast_serial_in(up, UART_LSR); + iir = ast_serial_in(up, UART_IIR); + serial_outp(up, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + UART_DBG("ttyDMA%d - enabling bad tx status\n", + port->line); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_inp(up, UART_LSR); + serial_inp(up, UART_RX); + serial_inp(up, UART_IIR); + serial_inp(up, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + // RX DMA + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; + up->port.icount.rx = 0; + + priv->tx_done = 1; + priv->tx_count = 0; + + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; +#ifdef SDDMA_RX_FIX +#else + priv->workaround = 0; +#endif + // UART_DBG("Sending trigger for % x\n", priv->dma_ch); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); +#ifdef SDDMA_RX_FIX +#else + add_timer(&priv->rx_timer); +#endif + priv->tx_dma_buf.head = 0; + priv->tx_dma_buf.tail = 0; + priv->tx_dma_buf.buf = xmit->buf; + + UART_DBG("head:0x%x tail:0x%x\n", xmit->head, xmit->tail); + xmit->head = 0; + xmit->tail = 0; + + priv->dma_tx_addr = dma_map_single(port->dev, priv->tx_dma_buf.buf, + UART_XMIT_SIZE, DMA_TO_DEVICE); + + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_tx_sdma_enqueue(priv->dma_ch, priv->dma_tx_addr); + ast_uart_tx_sdma_update(priv->dma_ch, 0); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); + return 0; +} + +static void ast25xx_uart_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + + UART_DBG("line[%d]\n", port->line); + priv->up = NULL; + + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + ast_serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + ast25xx_uart_clear_fifos(up); + + (void)ast_serial_in(up, UART_RX); + + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); +#ifdef SDDMA_RX_FIX +#else + del_timer_sync(&up->rx_timer); +#endif + + // Tx buffer will free by serial_core.c + free_irq(up->port.irq, ast_uart_irq); +} + +static unsigned int ast25xx_uart_get_divisor(struct uart_port *port, + unsigned int baud) +{ + unsigned int quot; + + quot = uart_get_divisor(port, baud); + + return quot; +} + +static void ast25xx_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (termios->c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = ast25xx_uart_get_divisor(port, baud); + + if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) { + if (baud < 2400) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; + else + fcr = uart_config[up->port.type].fcr; + } + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + ast_serial_out(up, UART_IER, up->ier); + + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + + serial_dl_write(up, quot); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +/* + * Resource handling. + */ +static int ast25xx_uart_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + int ret = 0; + + if (!up->port.mapbase) + return ret; + + if (!request_mem_region(up->port.mapbase, size, "ast-uart-dma")) { + ret = -EBUSY; + return ret; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap_nocache(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + return ret; + } + } + return ret; +} + +static void ast25xx_uart_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + + if (!up->port.mapbase) + return; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); +} + +static void ast25xx_uart_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + ret = ast25xx_uart_request_std_resource(up); + if (ret == 0) + ast25xx_uart_release_std_resource(up); + + return ret; +} + +static void ast25xx_uart_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = ast25xx_uart_request_std_resource(up); + if (ret < 0) + return; + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + if (up->port.type == PORT_UNKNOWN) + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + return 0; +} + +static const char *ast25xx_uart_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + + + +static unsigned int ast25xx_uart_serial_in(struct uart_port *port, int offset) +{ + offset = offset << port->regshift; + return readb(port->membase + offset); + +} + + +static void ast25xx_uart_serial_out(struct uart_port *port, + int offset, int value) +{ + offset = offset << port->regshift; + writeb(value, port->membase + offset); +} + +static const struct uart_ops ast25xx_uart_pops = { + .tx_empty = ast25xx_uart_tx_empty, + .set_mctrl = ast25xx_uart_set_mctrl, + .get_mctrl = ast25xx_uart_get_mctrl, + .stop_tx = ast25xx_uart_stop_tx, + .start_tx = ast25xx_uart_start_tx, + .stop_rx = ast25xx_uart_stop_rx, + .enable_ms = ast25xx_uart_enable_ms, + .break_ctl = ast25xx_uart_break_ctl, + .startup = ast25xx_uart_startup, + .shutdown = ast25xx_uart_shutdown, + .set_termios = ast25xx_uart_set_termios, + .type = ast25xx_uart_type, + .release_port = ast25xx_uart_release_port, + .request_port = ast25xx_uart_request_port, + .config_port = ast25xx_uart_config_port, + .verify_port = ast25xx_uart_verify_port, +}; + + + +/* + * Register a set of serial devices attached to a platform device. The + * list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +struct clk *clk; + +static int ast25xx_uart_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct ast_uart_priv_data *priv; + struct uart_8250_port port_8250; + struct uart_8250_port *up; + int ret; + u32 read, dma_channel = 0; + struct resource *res; + + if (UART_XMIT_SIZE > DMA_BUFF_SIZE) + UART_DBG("UART_XMIT_SIZE > DMA_BUFF_SIZE : Please Check\n"); + + priv = (struct ast_uart_priv_data *)devm_kzalloc(&pdev->dev, + sizeof(struct ast_uart_priv_data), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + up = &port_8250; + memset(up, 0, sizeof(struct uart_8250_port)); + up->port.flags = UPF_IOREMAP; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res == NULL) { + dev_err(&pdev->dev, "IRQ resource not found"); + return -ENODEV; + } + up->port.irq = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Register base not found"); + return -ENODEV; + } + up->port.mapbase = res->start; + + ret = ast25xx_uart_request_std_resource(up); + if (ret) { + dev_err(&pdev->dev, "ioremap_nocache Failed"); + return ret; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + dev_err(&pdev->dev, "missing controller clock"); + + ret = clk_prepare_enable(clk); + if (ret) + dev_err(&pdev->dev, "failed to enable DMA UART Clk"); + + up->port.uartclk = clk_get_rate(clk); + + if (of_property_read_u32(np, "reg-shift", &read) == 0) + up->port.regshift = read; + if (of_property_read_u32(np, "dma-channel", &read) == 0) { + dma_channel = read; + priv->dma_ch = dma_channel; + } + up->port.iotype = UPIO_MEM; + up->port.flags |= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + up->port.dev = &pdev->dev; + if (share_irqs) + up->port.flags |= UPF_SHARE_IRQ; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->port.type = PORT_16550; + up->port.iotype = UPIO_MEM; + up->port.flags = UPF_FIXED_TYPE; + up->port.startup = ast25xx_uart_startup; + up->port.shutdown = ast25xx_uart_shutdown; + up->port.set_termios = ast25xx_uart_set_termios; + up->port.set_mctrl = ast25xx_uart_set_mctrl; + up->port.serial_in = ast25xx_uart_serial_in; + up->port.serial_out = ast25xx_uart_serial_out; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + up->capabilities |= UART_CAP_FIFO; + + up->port.private_data = priv; + + ret = serial8250_register_8250_port(up); + if (ret < 0) { + dev_err(&pdev->dev, + "unable to registr port (IO%lx MEM%llx IRQ%d):%d\n", + up->port.iobase, (unsigned long long)up->port.mapbase, + up->port.irq, ret); + return ret; + } + priv->line = ret; + + tasklet_init(&priv->tx_tasklet, ast_uart_tx_sdma_tasklet_func, + (unsigned long)priv); +#ifdef SDDMA_RX_FIX + tasklet_init(&priv->rx_tasklet, ast_uart_rx_sdma_tasklet_func, + (unsigned long)priv); +#else + uart->rx_timer.data = (unsigned long)port; + uart->rx_timer.expires = jiffies + (HZ); + uart->rx_timer.function = ast_uart_rx_timer_func; + init_timer(&priv->rx_timer); +#endif + +//DMA request +#ifdef SDDMA_RX_FIX + priv->rx_dma_buf.buf = + ast_uart_rx_sdma_request(priv->dma_ch, ast_uart_rx_buffdone, + priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; +} +#else + priv->rx_dma_buf.buf = ast_uart_rx_sdma_request( + priv->dma_ch, priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } +#endif + if (ast_uart_tx_sdma_request( + priv->dma_ch, ast_uart_tx_buffdone, priv) < 0) { + UART_DBG("Error : failed to get tx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } + + + platform_set_drvdata(pdev, priv); + return 0; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ast25xx_uart_remove(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_unregister_port(priv->line); + return 0; +} + +static int ast25xx_uart_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_suspend_port(priv->line); + return 0; +} + +static int ast25xx_uart_resume(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_resume_port(priv->line); + return 0; +} + +static const struct of_device_id ast_serial_dt_ids[] = { + { .compatible = "aspeed,ast-sdma-uart", }, + { /* sentinel */ } +}; + +static struct platform_driver ast25xx_uart_driver = { + .probe = ast25xx_uart_probe, + .remove = ast25xx_uart_remove, + .suspend = ast25xx_uart_suspend, + .resume = ast25xx_uart_resume, + .driver = { + .name = "ast-uart-dma", + .of_match_table = of_match_ptr(ast_serial_dt_ids), + }, +}; + +static int __init ast_uart_init(void) +{ + int ret; + + if (nr_uarts > UART_DMA_NR) + nr_uarts = UART_DMA_NR; + + ret = ast_uart_sdma_probe(); + if (ret) { + UART_DBG("ast_uart_sdma_probe Failed ret = %d\n", ret); + goto out; + } + UART_DBG(KERN_INFO + "ast-uart-dma:UART driver with DMA%d ports IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); + + spin_lock_init(&ast_uart_irq[0].lock); + + ret = platform_driver_register(&ast25xx_uart_driver); + if (ret == 0) + goto out; + +out: + return ret; +} + +static void __exit ast_uart_exit(void) +{ + + platform_driver_unregister(&ast25xx_uart_driver); + +} +module_init(ast_uart_init); +module_exit(ast_uart_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("AST DMA serial driver"); +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR); -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ 1 file changed, 1928 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c diff --git a/drivers/tty/serial/8250/8250_ast2500_uart_dma.c b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c new file mode 100644 index 000000000000..6f3adcac9190 --- /dev/null +++ b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c @@ -0,0 +1,1928 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DMA UART Driver for ASPEED BMC chip: AST2500 + * + * Copyright (C) 2019 sudheer Kumar veliseti, Aspeed technology Inc. + * <open.sudheer@gmail.com> + * + */ +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/mutex.h> +#include <linux/nmi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#include "8250.h" + +#define DMA_BUFF_SIZE 0x1000 // 4096 +#define SDMA_RX_BUFF_SIZE 0x10000 // 65536 + +#define SDDMA_RX_FIX 1 +/* enum ast_uart_chan_op + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state + */ + +enum ast_uart_chan_op { + AST_UART_DMAOP_TRIGGER, + AST_UART_DMAOP_STOP, + AST_UART_DMAOP_PAUSE, +}; + +/* ast_uart_dma_cbfn_t * * buffer callback routine type */ +typedef void (*ast_uart_dma_cbfn_t)(void *dev_id, u16 len); + +struct ast_sdma_info { + u8 ch_no; + u8 direction; + u8 enable; + void *priv; + char *sdma_virt_addr; + dma_addr_t dma_phy_addr; + /* cdriver callbacks */ + ast_uart_dma_cbfn_t callback_fn; /* buffer done callback */ +}; + +#define AST_UART_SDMA_CH 12 + +struct ast_sdma_ch { + struct ast_sdma_info tx_dma_info[AST_UART_SDMA_CH]; + struct ast_sdma_info rx_dma_info[AST_UART_SDMA_CH]; +}; + +struct ast_sdma { + void __iomem *reg_base; + int dma_irq; + struct ast_sdma_ch *dma_ch; + struct regmap *map; +}; + + + +#define UART_TX_SDMA_EN 0x00 +#define UART_RX_SDMA_EN 0x04 +#define UART_SDMA_CONF 0x08 +#define UART_SDMA_TIMER 0x0C +#define UART_TX_SDMA_REST 0x20 +#define UART_RX_SDMA_REST 0x24 +#define UART_TX_SDMA_IER 0x30 +#define UART_TX_SDMA_ISR 0x34 +#define UART_RX_SDMA_IER 0x38 +#define UART_RX_SDMA_ISR 0x3C +#define UART_TX_R_POINT(x) (0x40 + (x * 0x20)) +#define UART_TX_W_POINT(x) (0x44 + (x * 0x20)) +#define UART_TX_SDMA_ADDR(x) (0x48 + (x * 0x20)) +#define UART_RX_R_POINT(x) (0x50 + (x * 0x20)) +#define UART_RX_W_POINT(x) (0x54 + (x * 0x20)) +#define UART_RX_SDMA_ADDR(x) (0x58 + (x * 0x20)) + +/* UART_TX_SDMA_EN-0x00 : UART TX DMA Enable */ +/* UART_RX_SDMA_EN-0x04 : UART RX DMA Enable */ +#define SDMA_CH_EN(x) (0x1 << (x)) + +/* UART_SDMA_CONF - 0x08 : Misc, Buffer size */ +#define SDMA_TX_BUFF_SIZE_MASK (0x3) +#define SDMA_SET_TX_BUFF_SIZE(x) (x) +#define SDMA_BUFF_SIZE_1KB (0x0) +#define SDMA_BUFF_SIZE_4KB (0x1) +#define SDMA_BUFF_SIZE_16KB (0x2) +#define SDMA_BUFF_SIZE_64KB (0x3) +#define SDMA_RX_BUFF_SIZE_MASK (0x3 << 2) +#define SDMA_SET_RX_BUFF_SIZE(x) (x << 2) +#define SDMA_TIMEOUT_DIS (0x1 << 4) + +/* UART_SDMA_TIMER-0x0C : UART DMA time out timer */ + +/* UART_TX_SDMA_IER 0x30 */ +/* UART_TX_SDMA_ISR 0x34 */ + +#define UART_SDMA11_INT (1 << 11) +#define UART_SDMA10_INT (1 << 10) +#define UART_SDMA9_INT (1 << 9) +#define UART_SDMA8_INT (1 << 8) +#define UART_SDMA7_INT (1 << 7) +#define UART_SDMA6_INT (1 << 6) +#define UART_SDMA5_INT (1 << 5) +#define UART_SDMA4_INT (1 << 4) +#define UART_SDMA3_INT (1 << 3) +#define UART_SDMA2_INT (1 << 2) +#define UART_SDMA1_INT (1 << 1) +#define UART_SDMA0_INT (1 << 0) + + +#define CONFIG_UART_DMA_DEBUG + +#ifdef CONFIG_UART_DMA_DEBUG +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define UART_DBG(fmt, args...) +#endif + +#define CONFIG_UART_TX_DMA_DEBUG 1 + +#ifdef CONFIG_UART_TX_DMA_DEBUG +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) +#else +#define UART_TX_DBG(fmt, args...) +#endif + +/* + * Configuration: + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option + * is unsafe when used on edge-triggered interrupts. + */ +static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; + +static unsigned int nr_uarts = CONFIG_AST_RUNTIME_DMA_UARTS; + +/* + * Debugging. + */ +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_AUTOCONF(fmt...) UART_DBG(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) \ + do { \ + } while (0) +#endif + +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_INTR(fmt...) UART_DBG(fmt) +#else +#define DEBUG_INTR(fmt...) \ + do { \ + } while (0) +#endif + +#define PASS_LIMIT 256 + +#include <asm/serial.h> + +#define UART_DMA_NR CONFIG_AST_NR_DMA_UARTS + + + +struct ast_uart_priv_data { + + unsigned short line; //index of uart port + struct uart_8250_port *up; + u8 dma_ch; // dma channel number + struct circ_buf rx_dma_buf; + struct circ_buf tx_dma_buf; + dma_addr_t dma_rx_addr; /* Mapped ADMA descr. table */ + dma_addr_t dma_tx_addr; /* Mapped ADMA descr. table */ +#ifdef SDDMA_RX_FIX + struct tasklet_struct rx_tasklet; +#else + struct timer_list rx_timer; +#endif + struct tasklet_struct tx_tasklet; + spinlock_t lock; + int tx_done; + int tx_count; +}; + + +static inline struct uart_8250_port * +to_uart_8250_port(struct uart_port *uart) { + return container_of(uart, struct uart_8250_port, port); +} + +struct irq_info { + spinlock_t lock; + struct uart_8250_port *up; +}; + +static struct irq_info ast_uart_irq[1]; +static DEFINE_MUTEX(ast_uart_mutex); + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 + | UART_FCR_DMA_SELECT, + .flags = UART_CAP_FIFO, + }, +}; + +/* sane hardware needs no mapping */ +#define map_8250_in_reg(up, offset) (offset) +#define map_8250_out_reg(up, offset) (offset) + +// SDMA - software Layer : ast-uart-sdma.c + +#define AST_UART_SDMA_DEBUG 1 + +#ifdef AST_UART_SDMA_DEBUG +#define SDMADBUG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define SDMADBUG(fmt, args...) +#endif + +static inline void ast_uart_sdma_write(struct ast_sdma *sdma, + u32 val, u32 reg) +{ + // SDMADBUG("uart dma write : val: %x , reg : %x\n",val,reg); + writel(val, sdma->reg_base + reg); +} + +static inline u32 ast_uart_sdma_read(struct ast_sdma *sdma, u32 reg) +{ + return readl(sdma->reg_base + reg); +} + +struct ast_sdma ast_uart_sdma; + +int ast_uart_rx_sdma_enqueue(u8 ch, dma_addr_t rx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, rx buff = %x\n", ch, rx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, rx_buff, UART_RX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_tx_sdma_enqueue(u8 ch, dma_addr_t tx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, tx buff = %x\n", ch, tx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, tx_buff, UART_TX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("Trigger\n"); + dma_ch->enable = 1; +#ifdef SDDMA_RX_FIX +#else + ast_uart_set_sdma_time_out(0xffff); +#endif + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) | (0x1 << ch), + UART_RX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + // disable engine + SDMADBUG("STOP\n"); + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) | + (0x1 << ch), + UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) & + ~(0x1 << ch), + UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(ch)); + ast_uart_sdma_write(sdma, dma_ch->dma_phy_addr, UART_RX_SDMA_ADDR(ch)); + break; + case AST_UART_DMAOP_PAUSE: + // disable engine + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + break; + } + + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("TRIGGER : Enable\n"); + dma_ch->enable = 1; + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) | (0x1 << ch), + UART_TX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + SDMADBUG("STOP : DISABLE & RESET\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) | + (0x1 << ch), + UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) & + ~(0x1 << ch), + UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(ch)); + break; + case AST_UART_DMAOP_PAUSE: + SDMADBUG("PAUSE : DISABLE\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + } + + local_irq_restore(flags); + return 0; +} + +u32 ast_uart_get_tx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_TX_R_POINT(ch)); +} + +int ast_uart_tx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("TX DMA CTRL [ch %d] point %d\n", ch, point); + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_TX_W_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_IER) | (1 << ch), + UART_TX_SDMA_IER); + + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("RX DMA CTRL [ch %d] point %x\n", ch, point); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_RX_R_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +#ifdef SDDMA_RX_FIX +char *ast_uart_rx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return 0; + } + dma_ch->priv = id; + + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_IER) | (1 << ch), + UART_RX_SDMA_IER); + + local_irq_restore(flags); + + return dma_ch->sdma_virt_addr; +} + +#else +char *ast_uart_rx_sdma_request(u8 ch, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + + local_irq_restore(flags); + return dma_ch->sdma_virt_addr; +} +#endif + +u16 ast_uart_get_rx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_RX_W_POINT(ch)); +} + +void ast_uart_set_sdma_time_out(u16 val) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + ast_uart_sdma_write(sdma, val, UART_SDMA_TIMER); +} + +static inline void ast_sdma_bufffdone(struct ast_sdma_info *sdma_ch) +{ + u32 len; + struct ast_sdma *sdma = &ast_uart_sdma; + + if (sdma_ch->enable == 0) { + SDMADBUG("sdma Please check ch_no %x %s!!!!!\n", + sdma_ch->ch_no, sdma_ch->direction ? "TX" : "RX"); + if (sdma_ch->direction) { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) + & ~(0x1 << sdma_ch->ch_no), UART_TX_SDMA_EN); + } else { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << sdma_ch->ch_no), UART_RX_SDMA_EN); + ast_uart_rx_sdma_update(sdma_ch->ch_no, + ast_uart_get_rx_sdma_pt(sdma_ch->ch_no)); + SDMADBUG("OFFSET : UART_RX_SDMA_EN = %x\n ", + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN)); + } + return; + } + + if (sdma_ch->direction) { + len = ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)); + SDMADBUG("tx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_TX_W_POINT(sdma_ch->ch_no)) + ); + } else { + SDMADBUG("rx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_RX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)) + ); + len = ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)); + } + + SDMADBUG("<dma dwn>: ch[%d] : %s ,len : %d\n", sdma_ch->ch_no, + sdma_ch->direction ? "tx" : "rx", len); + + if (sdma_ch->callback_fn != NULL) + (sdma_ch->callback_fn)(sdma_ch->priv, len); +} + +static irqreturn_t ast_uart_sdma_irq(int irq, void *dev_id) +{ + struct ast_sdma *sdma = (struct ast_sdma *)dev_id; + + u32 tx_sts = ast_uart_sdma_read(sdma, UART_TX_SDMA_ISR); + u32 rx_sts = ast_uart_sdma_read(sdma, UART_RX_SDMA_ISR); + + SDMADBUG("tx sts : %x, rx sts : %x\n", tx_sts, rx_sts); + + if ((tx_sts == 0) && (rx_sts == 0)) { + SDMADBUG("SDMA IRQ ERROR !!!\n"); + return IRQ_HANDLED; + } + + if (rx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[0])); + } else if (rx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[1])); + } else if (rx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[2])); + } else if (rx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[3])); + } else if (rx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[4])); + } else if (rx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[5])); + } else if (rx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[6])); + } else if (rx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[7])); + } else if (rx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[8])); + } else if (rx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[9])); + } else if (rx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[10])); + } else if (rx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[11])); + } else { + + } + + if (tx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[0])); + } else if (tx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[1])); + } else if (tx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[2])); + } else if (tx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[3])); + } else if (tx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[4])); + } else if (tx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[5])); + } else if (tx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[6])); + } else if (tx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[7])); + } else if (tx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[8])); + } else if (tx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[9])); + } else if (tx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[10])); + } else if (tx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[11])); + } else { + } + + return IRQ_HANDLED; +} + +static int ast_uart_sdma_probe(void) +{ + int i; + struct device_node *node; + int ret; + struct ast_sdma *sdma = &ast_uart_sdma; + char *rx_dma_virt_addr; + dma_addr_t rx_dma_phy_addr; + + sdma->dma_ch = kzalloc(sizeof(struct ast_sdma_ch), GFP_KERNEL); + if (!sdma->dma_ch) + return -ENOMEM; + + // sdma memory mapping + node = of_find_compatible_node(NULL, NULL, "aspeed,ast-uart-sdma"); + if (!node) + return -ENODEV; + + sdma->reg_base = of_iomap(node, 0); + if (IS_ERR(sdma->reg_base)) + return PTR_ERR(sdma->map); + rx_dma_virt_addr = dma_alloc_coherent(NULL, + SDMA_RX_BUFF_SIZE * AST_UART_SDMA_CH, &rx_dma_phy_addr, GFP_KERNEL); + + if (!rx_dma_virt_addr) + SDMADBUG(" rx_dma_virt_addr Errr : unable top alloc\n"); + + for (i = 0; i < AST_UART_SDMA_CH; i++) { + // TX ------------------------ + sdma->dma_ch->tx_dma_info[i].enable = 0; + sdma->dma_ch->tx_dma_info[i].ch_no = i; + sdma->dma_ch->tx_dma_info[i].direction = 1; + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(i)); + // RX ------------------------ + sdma->dma_ch->rx_dma_info[i].enable = 0; + sdma->dma_ch->rx_dma_info[i].ch_no = i; + sdma->dma_ch->rx_dma_info[i].direction = 0; + sdma->dma_ch->rx_dma_info[i].sdma_virt_addr = + rx_dma_virt_addr + (SDMA_RX_BUFF_SIZE * i); + sdma->dma_ch->rx_dma_info[i].dma_phy_addr = + rx_dma_phy_addr + (SDMA_RX_BUFF_SIZE * i); + ast_uart_sdma_write(sdma, + sdma->dma_ch->rx_dma_info[i].dma_phy_addr, + UART_RX_SDMA_ADDR(i)); + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(i)); + } + + ast_uart_sdma_write(sdma, 0xffffffff, UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0xffffffff, UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_EN); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_EN); + +#ifdef SDDMA_RX_FIX + ast_uart_sdma_write(sdma, 0x200, UART_SDMA_TIMER); +#else + ast_uart_sdma_write(sdma, 0xffff, UART_SDMA_TIMER); +#endif + + // TX + ast_uart_sdma_write(sdma, 0xfff, UART_TX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_IER); + + // RX + ast_uart_sdma_write(sdma, 0xfff, UART_RX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_IER); + + sdma->dma_irq = of_irq_get(node, 0); + ret = request_irq(sdma->dma_irq, ast_uart_sdma_irq, 0, + "sdma-intr", sdma); + if (ret) { + SDMADBUG("Unable to get UART SDMA IRQ %x\n", ret); + return -ENODEV; + } + + ast_uart_sdma_write(sdma, SDMA_SET_TX_BUFF_SIZE(SDMA_BUFF_SIZE_4KB) | + SDMA_SET_RX_BUFF_SIZE(SDMA_BUFF_SIZE_64KB), + UART_SDMA_CONF); + return 0; +} + +// END of SDMA Layer + +// UART Driver Layer + +static unsigned int ast_serial_in(struct uart_8250_port *up, int offset) +{ + offset = map_8250_in_reg(up, offset) << up->port.regshift; + return readb(up->port.membase + offset); +} + +static void ast_serial_out(struct uart_8250_port *up, int offset, int value) +{ + /* Save the offset before it's remapped */ + offset = map_8250_out_reg(up, offset) << up->port.regshift; + writeb(value, up->port.membase + offset); +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) ast_serial_in(up, offset) +#define serial_outp(up, offset, value) ast_serial_out(up, offset, value) + +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) + +static void ast_uart_tx_sdma_tasklet_func(unsigned long data) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit = NULL; + u32 tx_pt; + + + if (!up) + return; + xmit = &up->port.state->xmit; + spin_lock(&up->port.lock); + priv->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); + dma_sync_single_for_device(up->port.dev, priv->dma_tx_addr, + UART_XMIT_SIZE, DMA_TO_DEVICE); + tx_pt = ast_uart_get_tx_sdma_pt(priv->dma_ch); + + if (tx_pt > xmit->head) { + if ((tx_pt & 0xfffc) == 0) + ast_uart_tx_sdma_update(priv->dma_ch, 0xffff); + else + ast_uart_tx_sdma_update(priv->dma_ch, 0); + } else { + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + } + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + spin_unlock(&up->port.lock); +} + +static void ast_uart_tx_buffdone(void *dev_id, u16 len) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit; + + if (!up) + return; + xmit = &(up->port.state->xmit); + + UART_TX_DBG("line[%d] : tx len = % d\n", priv->line, len); + spin_lock(&up->port.lock); + xmit->tail = len; + UART_TX_DBG(" line[%d], xmit->head = %d, xmit->tail = % d\n", + priv->line, xmit->head, xmit->tail); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (xmit->head != xmit->tail) + tasklet_schedule(&priv->tx_tasklet); + + spin_unlock(&up->port.lock); +} + +#ifdef SDDMA_RX_FIX +static void ast_uart_rx_sdma_tasklet_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct tty_port *ttyport; + int count; + int copy = 0; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + + ttyport = &up->port.state->port; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + spin_lock(&up->port.lock); + if (rx_ring->head > rx_ring->tail) { + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + if (count) { + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + up->port.icount.rx += count; + tty_flip_buffer_push(ttyport); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + } + spin_unlock(&up->port.lock); +} + +static void ast_uart_rx_buffdone(void *dev_id, u16 len) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + UART_DBG("line[%d], head = %d,len:%d\n", + priv->line, priv->rx_dma_buf.head, len); + spin_lock(&up->port.lock); + rx_ring->head = len; + spin_unlock(&up->port.lock); + tasklet_schedule(&priv->rx_tasklet); +} + +#else +static void ast_uart_rx_timer_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct tty_port *ttyport; + struct circ_buf *rx_ring; + struct tty_struct *tty; + char flag; + int count; + int copy; + + + if (!up) + return; + ttyport = &up->port.state->port; + rx_ring = &up->rx_dma_buf; + tty = up->port.state->port.tty; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + rx_ring->head = ast_uart_get_rx_sdma_pt(priv->dma_ch); + del_timer(&up->rx_timer); + + if (rx_ring->head > rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + // UART_DBG("@@--%s-- ch = 0x%x\n", __func__, ch); + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + + if (count) { + //UART_DBG("\n count = % d\n", count); + up->port.icount.rx += count; + spin_lock(&up->port.lock); + tty_flip_buffer_push(ttyport); + spin_unlock(&up->port.lock); + //UART_DBG("update rx_ring->tail % x\n", rx_ring->tail); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + priv->workaround = 1; + } else { + if (priv->workaround) { + priv->workaround++; + if (priv->workaround > 1) + ast_uart_set_sdma_time_out(0); + else + ast_uart_set_sdma_time_out(0xffff); + } + } + add_timer(&up->rx_timer); +} +#endif + +/* + * FIFO support. + */ +static inline void ast25xx_uart_clear_fifos(struct uart_8250_port *p) +{ + serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(p, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(p, UART_FCR, 0); +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned long flags; + + UART_DBG("line[%d]\n", up->port.line); + if (!up->port.iobase && !up->port.mapbase && !up->port.membase) + return; + + DEBUG_AUTOCONF("ttyDMA%d : autoconf (0x%04lx, 0x%p) : ", up->port.line, + up->port.iobase, up->port.membase); + + spin_lock_irqsave(&up->port.lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + + if (up->port.type == PORT_UNKNOWN) + goto out; + + /* + * Reset the UART. + */ + ast25xx_uart_clear_fifos(up); + ast_serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); + DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name); +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + ast_serial_out(p, UART_IER, p->ier); + } +} + +static void ast25xx_uart_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_TX_DBG("line[%d]\n", up->port.line); + __stop_tx(up); +} + +static void transmit_chars(struct uart_8250_port *up); + +static void ast25xx_uart_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + + UART_TX_DBG("line[%d]\n", port->line); + tasklet_schedule(&priv->tx_tasklet); +} + +static void ast25xx_uart_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + ast_serial_out(up, UART_IER, up->ier); +} + +static void ast25xx_uart_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier |= UART_IER_MSI; + ast_serial_out(up, UART_IER, up->ier); +} + +static void transmit_chars(struct uart_8250_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + ast25xx_uart_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + ast_serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static unsigned int check_modem_status(struct uart_8250_port *up) +{ + unsigned int status = ast_serial_in(up, UART_MSR); + + UART_DBG("line[%d]\n", up->port.line); + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI + && up->port.state != NULL) { + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, + status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, + status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); + } + + return status; +} + +/* + * This handles the interrupt from one port. + */ +static inline void ast25xx_uart_handle_port(struct uart_8250_port *up) +{ + unsigned int status; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + status = serial_inp(up, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * This is the serial driver's interrupt routine. + */ +static irqreturn_t ast_uart_interrupt(int irq, void *dev_id) +{ + struct irq_info *i = dev_id; + int pass_counter = 0, handled = 0, end = 0; + + DEBUG_INTR("(%d) ", irq); + spin_lock(&i->lock); + + do { + struct uart_8250_port *up; + unsigned int iir; + + up = (struct uart_8250_port *)(i->up); + + iir = ast_serial_in(up, UART_IIR); + if (!(iir & UART_IIR_NO_INT)) { + ast25xx_uart_handle_port(up); + handled = 1; + + } else + end = 1; + + if (pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + UART_DBG(KERN_ERR + "ast-uart-dma:too much work for irq%d\n", irq); + break; + } + } while (end); + + spin_unlock(&i->lock); + + DEBUG_INTR("end.\n"); + + return IRQ_RETVAL(handled); +} + +static unsigned int ast25xx_uart_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + unsigned int lsr; + + UART_TX_DBG("line[%d]\n", up->port.line); + + spin_lock_irqsave(&up->port.lock, flags); + lsr = ast_serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&up->port.lock, flags); + + return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0; +} + +static unsigned int ast25xx_uart_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned int status; + unsigned int ret; + + status = check_modem_status(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void ast25xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char mcr = 0; + + mctrl = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + ast_serial_out(up, UART_MCR, mcr); + +} + +static void ast25xx_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + ast_serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ast25xx_uart_startup(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + // TX DMA + struct circ_buf *xmit = &up->port.state->xmit; + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + unsigned char lsr, iir; + int retval; + int irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; + + UART_DBG("%s\n", __func__); + + priv->up = up; + + UART_DBG("line[%d]\n", port->line); + up->capabilities = uart_config[up->port.type].flags; + up->mcr = 0; + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + ast25xx_uart_clear_fifos(up); + /* + * Clear the interrupt registers. + */ + (void)serial_inp(up, UART_LSR); + (void)serial_inp(up, UART_RX); + (void)serial_inp(up, UART_IIR); + (void)serial_inp(up, UART_MSR); + + ast_uart_irq[0].up = up; + retval = request_irq(up->port.irq, ast_uart_interrupt, irq_flags, + "ast-uart-dma", ast_uart_irq); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl |= TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_outp(up, UART_IER, UART_IER_THRI); + lsr = ast_serial_in(up, UART_LSR); + iir = ast_serial_in(up, UART_IIR); + serial_outp(up, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + UART_DBG("ttyDMA%d - enabling bad tx status\n", + port->line); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_inp(up, UART_LSR); + serial_inp(up, UART_RX); + serial_inp(up, UART_IIR); + serial_inp(up, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + // RX DMA + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; + up->port.icount.rx = 0; + + priv->tx_done = 1; + priv->tx_count = 0; + + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; +#ifdef SDDMA_RX_FIX +#else + priv->workaround = 0; +#endif + // UART_DBG("Sending trigger for % x\n", priv->dma_ch); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); +#ifdef SDDMA_RX_FIX +#else + add_timer(&priv->rx_timer); +#endif + priv->tx_dma_buf.head = 0; + priv->tx_dma_buf.tail = 0; + priv->tx_dma_buf.buf = xmit->buf; + + UART_DBG("head:0x%x tail:0x%x\n", xmit->head, xmit->tail); + xmit->head = 0; + xmit->tail = 0; + + priv->dma_tx_addr = dma_map_single(port->dev, priv->tx_dma_buf.buf, + UART_XMIT_SIZE, DMA_TO_DEVICE); + + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_tx_sdma_enqueue(priv->dma_ch, priv->dma_tx_addr); + ast_uart_tx_sdma_update(priv->dma_ch, 0); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); + return 0; +} + +static void ast25xx_uart_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + + UART_DBG("line[%d]\n", port->line); + priv->up = NULL; + + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + ast_serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + ast25xx_uart_clear_fifos(up); + + (void)ast_serial_in(up, UART_RX); + + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); +#ifdef SDDMA_RX_FIX +#else + del_timer_sync(&up->rx_timer); +#endif + + // Tx buffer will free by serial_core.c + free_irq(up->port.irq, ast_uart_irq); +} + +static unsigned int ast25xx_uart_get_divisor(struct uart_port *port, + unsigned int baud) +{ + unsigned int quot; + + quot = uart_get_divisor(port, baud); + + return quot; +} + +static void ast25xx_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (termios->c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = ast25xx_uart_get_divisor(port, baud); + + if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) { + if (baud < 2400) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; + else + fcr = uart_config[up->port.type].fcr; + } + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + ast_serial_out(up, UART_IER, up->ier); + + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + + serial_dl_write(up, quot); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +/* + * Resource handling. + */ +static int ast25xx_uart_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + int ret = 0; + + if (!up->port.mapbase) + return ret; + + if (!request_mem_region(up->port.mapbase, size, "ast-uart-dma")) { + ret = -EBUSY; + return ret; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap_nocache(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + return ret; + } + } + return ret; +} + +static void ast25xx_uart_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + + if (!up->port.mapbase) + return; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); +} + +static void ast25xx_uart_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + ret = ast25xx_uart_request_std_resource(up); + if (ret == 0) + ast25xx_uart_release_std_resource(up); + + return ret; +} + +static void ast25xx_uart_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = ast25xx_uart_request_std_resource(up); + if (ret < 0) + return; + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + if (up->port.type == PORT_UNKNOWN) + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + return 0; +} + +static const char *ast25xx_uart_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + + + +static unsigned int ast25xx_uart_serial_in(struct uart_port *port, int offset) +{ + offset = offset << port->regshift; + return readb(port->membase + offset); + +} + + +static void ast25xx_uart_serial_out(struct uart_port *port, + int offset, int value) +{ + offset = offset << port->regshift; + writeb(value, port->membase + offset); +} + +static const struct uart_ops ast25xx_uart_pops = { + .tx_empty = ast25xx_uart_tx_empty, + .set_mctrl = ast25xx_uart_set_mctrl, + .get_mctrl = ast25xx_uart_get_mctrl, + .stop_tx = ast25xx_uart_stop_tx, + .start_tx = ast25xx_uart_start_tx, + .stop_rx = ast25xx_uart_stop_rx, + .enable_ms = ast25xx_uart_enable_ms, + .break_ctl = ast25xx_uart_break_ctl, + .startup = ast25xx_uart_startup, + .shutdown = ast25xx_uart_shutdown, + .set_termios = ast25xx_uart_set_termios, + .type = ast25xx_uart_type, + .release_port = ast25xx_uart_release_port, + .request_port = ast25xx_uart_request_port, + .config_port = ast25xx_uart_config_port, + .verify_port = ast25xx_uart_verify_port, +}; + + + +/* + * Register a set of serial devices attached to a platform device. The + * list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +struct clk *clk; + +static int ast25xx_uart_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct ast_uart_priv_data *priv; + struct uart_8250_port port_8250; + struct uart_8250_port *up; + int ret; + u32 read, dma_channel = 0; + struct resource *res; + + if (UART_XMIT_SIZE > DMA_BUFF_SIZE) + UART_DBG("UART_XMIT_SIZE > DMA_BUFF_SIZE : Please Check\n"); + + priv = (struct ast_uart_priv_data *)devm_kzalloc(&pdev->dev, + sizeof(struct ast_uart_priv_data), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + up = &port_8250; + memset(up, 0, sizeof(struct uart_8250_port)); + up->port.flags = UPF_IOREMAP; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res == NULL) { + dev_err(&pdev->dev, "IRQ resource not found"); + return -ENODEV; + } + up->port.irq = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Register base not found"); + return -ENODEV; + } + up->port.mapbase = res->start; + + ret = ast25xx_uart_request_std_resource(up); + if (ret) { + dev_err(&pdev->dev, "ioremap_nocache Failed"); + return ret; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + dev_err(&pdev->dev, "missing controller clock"); + + ret = clk_prepare_enable(clk); + if (ret) + dev_err(&pdev->dev, "failed to enable DMA UART Clk"); + + up->port.uartclk = clk_get_rate(clk); + + if (of_property_read_u32(np, "reg-shift", &read) == 0) + up->port.regshift = read; + if (of_property_read_u32(np, "dma-channel", &read) == 0) { + dma_channel = read; + priv->dma_ch = dma_channel; + } + up->port.iotype = UPIO_MEM; + up->port.flags |= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + up->port.dev = &pdev->dev; + if (share_irqs) + up->port.flags |= UPF_SHARE_IRQ; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->port.type = PORT_16550; + up->port.iotype = UPIO_MEM; + up->port.flags = UPF_FIXED_TYPE; + up->port.startup = ast25xx_uart_startup; + up->port.shutdown = ast25xx_uart_shutdown; + up->port.set_termios = ast25xx_uart_set_termios; + up->port.set_mctrl = ast25xx_uart_set_mctrl; + up->port.serial_in = ast25xx_uart_serial_in; + up->port.serial_out = ast25xx_uart_serial_out; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + up->capabilities |= UART_CAP_FIFO; + + up->port.private_data = priv; + + ret = serial8250_register_8250_port(up); + if (ret < 0) { + dev_err(&pdev->dev, + "unable to registr port (IO%lx MEM%llx IRQ%d):%d\n", + up->port.iobase, (unsigned long long)up->port.mapbase, + up->port.irq, ret); + return ret; + } + priv->line = ret; + + tasklet_init(&priv->tx_tasklet, ast_uart_tx_sdma_tasklet_func, + (unsigned long)priv); +#ifdef SDDMA_RX_FIX + tasklet_init(&priv->rx_tasklet, ast_uart_rx_sdma_tasklet_func, + (unsigned long)priv); +#else + uart->rx_timer.data = (unsigned long)port; + uart->rx_timer.expires = jiffies + (HZ); + uart->rx_timer.function = ast_uart_rx_timer_func; + init_timer(&priv->rx_timer); +#endif + +//DMA request +#ifdef SDDMA_RX_FIX + priv->rx_dma_buf.buf = + ast_uart_rx_sdma_request(priv->dma_ch, ast_uart_rx_buffdone, + priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; +} +#else + priv->rx_dma_buf.buf = ast_uart_rx_sdma_request( + priv->dma_ch, priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } +#endif + if (ast_uart_tx_sdma_request( + priv->dma_ch, ast_uart_tx_buffdone, priv) < 0) { + UART_DBG("Error : failed to get tx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } + + + platform_set_drvdata(pdev, priv); + return 0; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ast25xx_uart_remove(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_unregister_port(priv->line); + return 0; +} + +static int ast25xx_uart_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_suspend_port(priv->line); + return 0; +} + +static int ast25xx_uart_resume(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_resume_port(priv->line); + return 0; +} + +static const struct of_device_id ast_serial_dt_ids[] = { + { .compatible = "aspeed,ast-sdma-uart", }, + { /* sentinel */ } +}; + +static struct platform_driver ast25xx_uart_driver = { + .probe = ast25xx_uart_probe, + .remove = ast25xx_uart_remove, + .suspend = ast25xx_uart_suspend, + .resume = ast25xx_uart_resume, + .driver = { + .name = "ast-uart-dma", + .of_match_table = of_match_ptr(ast_serial_dt_ids), + }, +}; + +static int __init ast_uart_init(void) +{ + int ret; + + if (nr_uarts > UART_DMA_NR) + nr_uarts = UART_DMA_NR; + + ret = ast_uart_sdma_probe(); + if (ret) { + UART_DBG("ast_uart_sdma_probe Failed ret = %d\n", ret); + goto out; + } + UART_DBG(KERN_INFO + "ast-uart-dma:UART driver with DMA%d ports IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); + + spin_lock_init(&ast_uart_irq[0].lock); + + ret = platform_driver_register(&ast25xx_uart_driver); + if (ret == 0) + goto out; + +out: + return ret; +} + +static void __exit ast_uart_exit(void) +{ + + platform_driver_unregister(&ast25xx_uart_driver); + +} +module_init(ast_uart_init); +module_exit(ast_uart_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("AST DMA serial driver"); +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR); -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../tty/serial/8250/8250_ast2500_uart_dma.c | 1928 +++++++++++++++++ 1 file changed, 1928 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c diff --git a/drivers/tty/serial/8250/8250_ast2500_uart_dma.c b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c new file mode 100644 index 000000000000..6f3adcac9190 --- /dev/null +++ b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c @@ -0,0 +1,1928 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DMA UART Driver for ASPEED BMC chip: AST2500 + * + * Copyright (C) 2019 sudheer Kumar veliseti, Aspeed technology Inc. + * <open.sudheer@gmail.com> + * + */ +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/mutex.h> +#include <linux/nmi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#include "8250.h" + +#define DMA_BUFF_SIZE 0x1000 // 4096 +#define SDMA_RX_BUFF_SIZE 0x10000 // 65536 + +#define SDDMA_RX_FIX 1 +/* enum ast_uart_chan_op + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state + */ + +enum ast_uart_chan_op { + AST_UART_DMAOP_TRIGGER, + AST_UART_DMAOP_STOP, + AST_UART_DMAOP_PAUSE, +}; + +/* ast_uart_dma_cbfn_t * * buffer callback routine type */ +typedef void (*ast_uart_dma_cbfn_t)(void *dev_id, u16 len); + +struct ast_sdma_info { + u8 ch_no; + u8 direction; + u8 enable; + void *priv; + char *sdma_virt_addr; + dma_addr_t dma_phy_addr; + /* cdriver callbacks */ + ast_uart_dma_cbfn_t callback_fn; /* buffer done callback */ +}; + +#define AST_UART_SDMA_CH 12 + +struct ast_sdma_ch { + struct ast_sdma_info tx_dma_info[AST_UART_SDMA_CH]; + struct ast_sdma_info rx_dma_info[AST_UART_SDMA_CH]; +}; + +struct ast_sdma { + void __iomem *reg_base; + int dma_irq; + struct ast_sdma_ch *dma_ch; + struct regmap *map; +}; + + + +#define UART_TX_SDMA_EN 0x00 +#define UART_RX_SDMA_EN 0x04 +#define UART_SDMA_CONF 0x08 +#define UART_SDMA_TIMER 0x0C +#define UART_TX_SDMA_REST 0x20 +#define UART_RX_SDMA_REST 0x24 +#define UART_TX_SDMA_IER 0x30 +#define UART_TX_SDMA_ISR 0x34 +#define UART_RX_SDMA_IER 0x38 +#define UART_RX_SDMA_ISR 0x3C +#define UART_TX_R_POINT(x) (0x40 + (x * 0x20)) +#define UART_TX_W_POINT(x) (0x44 + (x * 0x20)) +#define UART_TX_SDMA_ADDR(x) (0x48 + (x * 0x20)) +#define UART_RX_R_POINT(x) (0x50 + (x * 0x20)) +#define UART_RX_W_POINT(x) (0x54 + (x * 0x20)) +#define UART_RX_SDMA_ADDR(x) (0x58 + (x * 0x20)) + +/* UART_TX_SDMA_EN-0x00 : UART TX DMA Enable */ +/* UART_RX_SDMA_EN-0x04 : UART RX DMA Enable */ +#define SDMA_CH_EN(x) (0x1 << (x)) + +/* UART_SDMA_CONF - 0x08 : Misc, Buffer size */ +#define SDMA_TX_BUFF_SIZE_MASK (0x3) +#define SDMA_SET_TX_BUFF_SIZE(x) (x) +#define SDMA_BUFF_SIZE_1KB (0x0) +#define SDMA_BUFF_SIZE_4KB (0x1) +#define SDMA_BUFF_SIZE_16KB (0x2) +#define SDMA_BUFF_SIZE_64KB (0x3) +#define SDMA_RX_BUFF_SIZE_MASK (0x3 << 2) +#define SDMA_SET_RX_BUFF_SIZE(x) (x << 2) +#define SDMA_TIMEOUT_DIS (0x1 << 4) + +/* UART_SDMA_TIMER-0x0C : UART DMA time out timer */ + +/* UART_TX_SDMA_IER 0x30 */ +/* UART_TX_SDMA_ISR 0x34 */ + +#define UART_SDMA11_INT (1 << 11) +#define UART_SDMA10_INT (1 << 10) +#define UART_SDMA9_INT (1 << 9) +#define UART_SDMA8_INT (1 << 8) +#define UART_SDMA7_INT (1 << 7) +#define UART_SDMA6_INT (1 << 6) +#define UART_SDMA5_INT (1 << 5) +#define UART_SDMA4_INT (1 << 4) +#define UART_SDMA3_INT (1 << 3) +#define UART_SDMA2_INT (1 << 2) +#define UART_SDMA1_INT (1 << 1) +#define UART_SDMA0_INT (1 << 0) + + +#define CONFIG_UART_DMA_DEBUG + +#ifdef CONFIG_UART_DMA_DEBUG +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define UART_DBG(fmt, args...) +#endif + +#define CONFIG_UART_TX_DMA_DEBUG 1 + +#ifdef CONFIG_UART_TX_DMA_DEBUG +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) +#else +#define UART_TX_DBG(fmt, args...) +#endif + +/* + * Configuration: + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option + * is unsafe when used on edge-triggered interrupts. + */ +static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; + +static unsigned int nr_uarts = CONFIG_AST_RUNTIME_DMA_UARTS; + +/* + * Debugging. + */ +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_AUTOCONF(fmt...) UART_DBG(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) \ + do { \ + } while (0) +#endif + +#ifdef CONFIG_UART_DMA_DEBUG +#define DEBUG_INTR(fmt...) UART_DBG(fmt) +#else +#define DEBUG_INTR(fmt...) \ + do { \ + } while (0) +#endif + +#define PASS_LIMIT 256 + +#include <asm/serial.h> + +#define UART_DMA_NR CONFIG_AST_NR_DMA_UARTS + + + +struct ast_uart_priv_data { + + unsigned short line; //index of uart port + struct uart_8250_port *up; + u8 dma_ch; // dma channel number + struct circ_buf rx_dma_buf; + struct circ_buf tx_dma_buf; + dma_addr_t dma_rx_addr; /* Mapped ADMA descr. table */ + dma_addr_t dma_tx_addr; /* Mapped ADMA descr. table */ +#ifdef SDDMA_RX_FIX + struct tasklet_struct rx_tasklet; +#else + struct timer_list rx_timer; +#endif + struct tasklet_struct tx_tasklet; + spinlock_t lock; + int tx_done; + int tx_count; +}; + + +static inline struct uart_8250_port * +to_uart_8250_port(struct uart_port *uart) { + return container_of(uart, struct uart_8250_port, port); +} + +struct irq_info { + spinlock_t lock; + struct uart_8250_port *up; +}; + +static struct irq_info ast_uart_irq[1]; +static DEFINE_MUTEX(ast_uart_mutex); + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 + | UART_FCR_DMA_SELECT, + .flags = UART_CAP_FIFO, + }, +}; + +/* sane hardware needs no mapping */ +#define map_8250_in_reg(up, offset) (offset) +#define map_8250_out_reg(up, offset) (offset) + +// SDMA - software Layer : ast-uart-sdma.c + +#define AST_UART_SDMA_DEBUG 1 + +#ifdef AST_UART_SDMA_DEBUG +#define SDMADBUG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) +#else +#define SDMADBUG(fmt, args...) +#endif + +static inline void ast_uart_sdma_write(struct ast_sdma *sdma, + u32 val, u32 reg) +{ + // SDMADBUG("uart dma write : val: %x , reg : %x\n",val,reg); + writel(val, sdma->reg_base + reg); +} + +static inline u32 ast_uart_sdma_read(struct ast_sdma *sdma, u32 reg) +{ + return readl(sdma->reg_base + reg); +} + +struct ast_sdma ast_uart_sdma; + +int ast_uart_rx_sdma_enqueue(u8 ch, dma_addr_t rx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, rx buff = %x\n", ch, rx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, rx_buff, UART_RX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_tx_sdma_enqueue(u8 ch, dma_addr_t tx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("ch = %d, tx buff = %x\n", ch, tx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, tx_buff, UART_TX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("Trigger\n"); + dma_ch->enable = 1; +#ifdef SDDMA_RX_FIX +#else + ast_uart_set_sdma_time_out(0xffff); +#endif + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) | (0x1 << ch), + UART_RX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + // disable engine + SDMADBUG("STOP\n"); + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) | + (0x1 << ch), + UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) & + ~(0x1 << ch), + UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(ch)); + ast_uart_sdma_write(sdma, dma_ch->dma_phy_addr, UART_RX_SDMA_ADDR(ch)); + break; + case AST_UART_DMAOP_PAUSE: + // disable engine + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + break; + } + + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + SDMADBUG("TRIGGER : Enable\n"); + dma_ch->enable = 1; + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) | (0x1 << ch), + UART_TX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + SDMADBUG("STOP : DISABLE & RESET\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) | + (0x1 << ch), + UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) & + ~(0x1 << ch), + UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(ch)); + break; + case AST_UART_DMAOP_PAUSE: + SDMADBUG("PAUSE : DISABLE\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + } + + local_irq_restore(flags); + return 0; +} + +u32 ast_uart_get_tx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_TX_R_POINT(ch)); +} + +int ast_uart_tx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("TX DMA CTRL [ch %d] point %d\n", ch, point); + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_TX_W_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + SDMADBUG("TX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_IER) | (1 << ch), + UART_TX_SDMA_IER); + + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + SDMADBUG("RX DMA CTRL [ch %d] point %x\n", ch, point); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_RX_R_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +#ifdef SDDMA_RX_FIX +char *ast_uart_rx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return 0; + } + dma_ch->priv = id; + + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_IER) | (1 << ch), + UART_RX_SDMA_IER); + + local_irq_restore(flags); + + return dma_ch->sdma_virt_addr; +} + +#else +char *ast_uart_rx_sdma_request(u8 ch, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + SDMADBUG("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + + local_irq_restore(flags); + return dma_ch->sdma_virt_addr; +} +#endif + +u16 ast_uart_get_rx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_RX_W_POINT(ch)); +} + +void ast_uart_set_sdma_time_out(u16 val) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + ast_uart_sdma_write(sdma, val, UART_SDMA_TIMER); +} + +static inline void ast_sdma_bufffdone(struct ast_sdma_info *sdma_ch) +{ + u32 len; + struct ast_sdma *sdma = &ast_uart_sdma; + + if (sdma_ch->enable == 0) { + SDMADBUG("sdma Please check ch_no %x %s!!!!!\n", + sdma_ch->ch_no, sdma_ch->direction ? "TX" : "RX"); + if (sdma_ch->direction) { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) + & ~(0x1 << sdma_ch->ch_no), UART_TX_SDMA_EN); + } else { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << sdma_ch->ch_no), UART_RX_SDMA_EN); + ast_uart_rx_sdma_update(sdma_ch->ch_no, + ast_uart_get_rx_sdma_pt(sdma_ch->ch_no)); + SDMADBUG("OFFSET : UART_RX_SDMA_EN = %x\n ", + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN)); + } + return; + } + + if (sdma_ch->direction) { + len = ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)); + SDMADBUG("tx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_TX_W_POINT(sdma_ch->ch_no)) + ); + } else { + SDMADBUG("rx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_RX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)) + ); + len = ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)); + } + + SDMADBUG("<dma dwn>: ch[%d] : %s ,len : %d\n", sdma_ch->ch_no, + sdma_ch->direction ? "tx" : "rx", len); + + if (sdma_ch->callback_fn != NULL) + (sdma_ch->callback_fn)(sdma_ch->priv, len); +} + +static irqreturn_t ast_uart_sdma_irq(int irq, void *dev_id) +{ + struct ast_sdma *sdma = (struct ast_sdma *)dev_id; + + u32 tx_sts = ast_uart_sdma_read(sdma, UART_TX_SDMA_ISR); + u32 rx_sts = ast_uart_sdma_read(sdma, UART_RX_SDMA_ISR); + + SDMADBUG("tx sts : %x, rx sts : %x\n", tx_sts, rx_sts); + + if ((tx_sts == 0) && (rx_sts == 0)) { + SDMADBUG("SDMA IRQ ERROR !!!\n"); + return IRQ_HANDLED; + } + + if (rx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[0])); + } else if (rx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[1])); + } else if (rx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[2])); + } else if (rx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[3])); + } else if (rx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[4])); + } else if (rx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[5])); + } else if (rx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[6])); + } else if (rx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[7])); + } else if (rx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[8])); + } else if (rx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[9])); + } else if (rx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[10])); + } else if (rx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[11])); + } else { + + } + + if (tx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[0])); + } else if (tx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[1])); + } else if (tx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[2])); + } else if (tx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[3])); + } else if (tx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[4])); + } else if (tx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[5])); + } else if (tx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[6])); + } else if (tx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[7])); + } else if (tx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[8])); + } else if (tx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[9])); + } else if (tx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[10])); + } else if (tx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[11])); + } else { + } + + return IRQ_HANDLED; +} + +static int ast_uart_sdma_probe(void) +{ + int i; + struct device_node *node; + int ret; + struct ast_sdma *sdma = &ast_uart_sdma; + char *rx_dma_virt_addr; + dma_addr_t rx_dma_phy_addr; + + sdma->dma_ch = kzalloc(sizeof(struct ast_sdma_ch), GFP_KERNEL); + if (!sdma->dma_ch) + return -ENOMEM; + + // sdma memory mapping + node = of_find_compatible_node(NULL, NULL, "aspeed,ast-uart-sdma"); + if (!node) + return -ENODEV; + + sdma->reg_base = of_iomap(node, 0); + if (IS_ERR(sdma->reg_base)) + return PTR_ERR(sdma->map); + rx_dma_virt_addr = dma_alloc_coherent(NULL, + SDMA_RX_BUFF_SIZE * AST_UART_SDMA_CH, &rx_dma_phy_addr, GFP_KERNEL); + + if (!rx_dma_virt_addr) + SDMADBUG(" rx_dma_virt_addr Errr : unable top alloc\n"); + + for (i = 0; i < AST_UART_SDMA_CH; i++) { + // TX ------------------------ + sdma->dma_ch->tx_dma_info[i].enable = 0; + sdma->dma_ch->tx_dma_info[i].ch_no = i; + sdma->dma_ch->tx_dma_info[i].direction = 1; + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(i)); + // RX ------------------------ + sdma->dma_ch->rx_dma_info[i].enable = 0; + sdma->dma_ch->rx_dma_info[i].ch_no = i; + sdma->dma_ch->rx_dma_info[i].direction = 0; + sdma->dma_ch->rx_dma_info[i].sdma_virt_addr = + rx_dma_virt_addr + (SDMA_RX_BUFF_SIZE * i); + sdma->dma_ch->rx_dma_info[i].dma_phy_addr = + rx_dma_phy_addr + (SDMA_RX_BUFF_SIZE * i); + ast_uart_sdma_write(sdma, + sdma->dma_ch->rx_dma_info[i].dma_phy_addr, + UART_RX_SDMA_ADDR(i)); + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(i)); + } + + ast_uart_sdma_write(sdma, 0xffffffff, UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0xffffffff, UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_EN); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_EN); + +#ifdef SDDMA_RX_FIX + ast_uart_sdma_write(sdma, 0x200, UART_SDMA_TIMER); +#else + ast_uart_sdma_write(sdma, 0xffff, UART_SDMA_TIMER); +#endif + + // TX + ast_uart_sdma_write(sdma, 0xfff, UART_TX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_IER); + + // RX + ast_uart_sdma_write(sdma, 0xfff, UART_RX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_IER); + + sdma->dma_irq = of_irq_get(node, 0); + ret = request_irq(sdma->dma_irq, ast_uart_sdma_irq, 0, + "sdma-intr", sdma); + if (ret) { + SDMADBUG("Unable to get UART SDMA IRQ %x\n", ret); + return -ENODEV; + } + + ast_uart_sdma_write(sdma, SDMA_SET_TX_BUFF_SIZE(SDMA_BUFF_SIZE_4KB) | + SDMA_SET_RX_BUFF_SIZE(SDMA_BUFF_SIZE_64KB), + UART_SDMA_CONF); + return 0; +} + +// END of SDMA Layer + +// UART Driver Layer + +static unsigned int ast_serial_in(struct uart_8250_port *up, int offset) +{ + offset = map_8250_in_reg(up, offset) << up->port.regshift; + return readb(up->port.membase + offset); +} + +static void ast_serial_out(struct uart_8250_port *up, int offset, int value) +{ + /* Save the offset before it's remapped */ + offset = map_8250_out_reg(up, offset) << up->port.regshift; + writeb(value, up->port.membase + offset); +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) ast_serial_in(up, offset) +#define serial_outp(up, offset, value) ast_serial_out(up, offset, value) + +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) + +static void ast_uart_tx_sdma_tasklet_func(unsigned long data) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit = NULL; + u32 tx_pt; + + + if (!up) + return; + xmit = &up->port.state->xmit; + spin_lock(&up->port.lock); + priv->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); + dma_sync_single_for_device(up->port.dev, priv->dma_tx_addr, + UART_XMIT_SIZE, DMA_TO_DEVICE); + tx_pt = ast_uart_get_tx_sdma_pt(priv->dma_ch); + + if (tx_pt > xmit->head) { + if ((tx_pt & 0xfffc) == 0) + ast_uart_tx_sdma_update(priv->dma_ch, 0xffff); + else + ast_uart_tx_sdma_update(priv->dma_ch, 0); + } else { + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + } + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + spin_unlock(&up->port.lock); +} + +static void ast_uart_tx_buffdone(void *dev_id, u16 len) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit; + + if (!up) + return; + xmit = &(up->port.state->xmit); + + UART_TX_DBG("line[%d] : tx len = % d\n", priv->line, len); + spin_lock(&up->port.lock); + xmit->tail = len; + UART_TX_DBG(" line[%d], xmit->head = %d, xmit->tail = % d\n", + priv->line, xmit->head, xmit->tail); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (xmit->head != xmit->tail) + tasklet_schedule(&priv->tx_tasklet); + + spin_unlock(&up->port.lock); +} + +#ifdef SDDMA_RX_FIX +static void ast_uart_rx_sdma_tasklet_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct tty_port *ttyport; + int count; + int copy = 0; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + + ttyport = &up->port.state->port; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + spin_lock(&up->port.lock); + if (rx_ring->head > rx_ring->tail) { + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + if (count) { + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + up->port.icount.rx += count; + tty_flip_buffer_push(ttyport); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + } + spin_unlock(&up->port.lock); +} + +static void ast_uart_rx_buffdone(void *dev_id, u16 len) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + UART_DBG("line[%d], head = %d,len:%d\n", + priv->line, priv->rx_dma_buf.head, len); + spin_lock(&up->port.lock); + rx_ring->head = len; + spin_unlock(&up->port.lock); + tasklet_schedule(&priv->rx_tasklet); +} + +#else +static void ast_uart_rx_timer_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct tty_port *ttyport; + struct circ_buf *rx_ring; + struct tty_struct *tty; + char flag; + int count; + int copy; + + + if (!up) + return; + ttyport = &up->port.state->port; + rx_ring = &up->rx_dma_buf; + tty = up->port.state->port.tty; + + UART_DBG("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + rx_ring->head = ast_uart_get_rx_sdma_pt(priv->dma_ch); + del_timer(&up->rx_timer); + + if (rx_ring->head > rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + // UART_DBG("@@--%s-- ch = 0x%x\n", __func__, ch); + } + + if (copy != count) + UART_DBG(" !!!!!!!!ERROR 111\n"); + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + + if (count) { + //UART_DBG("\n count = % d\n", count); + up->port.icount.rx += count; + spin_lock(&up->port.lock); + tty_flip_buffer_push(ttyport); + spin_unlock(&up->port.lock); + //UART_DBG("update rx_ring->tail % x\n", rx_ring->tail); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + priv->workaround = 1; + } else { + if (priv->workaround) { + priv->workaround++; + if (priv->workaround > 1) + ast_uart_set_sdma_time_out(0); + else + ast_uart_set_sdma_time_out(0xffff); + } + } + add_timer(&up->rx_timer); +} +#endif + +/* + * FIFO support. + */ +static inline void ast25xx_uart_clear_fifos(struct uart_8250_port *p) +{ + serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(p, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(p, UART_FCR, 0); +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned long flags; + + UART_DBG("line[%d]\n", up->port.line); + if (!up->port.iobase && !up->port.mapbase && !up->port.membase) + return; + + DEBUG_AUTOCONF("ttyDMA%d : autoconf (0x%04lx, 0x%p) : ", up->port.line, + up->port.iobase, up->port.membase); + + spin_lock_irqsave(&up->port.lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + + if (up->port.type == PORT_UNKNOWN) + goto out; + + /* + * Reset the UART. + */ + ast25xx_uart_clear_fifos(up); + ast_serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); + DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name); +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + ast_serial_out(p, UART_IER, p->ier); + } +} + +static void ast25xx_uart_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_TX_DBG("line[%d]\n", up->port.line); + __stop_tx(up); +} + +static void transmit_chars(struct uart_8250_port *up); + +static void ast25xx_uart_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + + UART_TX_DBG("line[%d]\n", port->line); + tasklet_schedule(&priv->tx_tasklet); +} + +static void ast25xx_uart_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + ast_serial_out(up, UART_IER, up->ier); +} + +static void ast25xx_uart_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + UART_DBG("line[%d]\n", port->line); + up->ier |= UART_IER_MSI; + ast_serial_out(up, UART_IER, up->ier); +} + +static void transmit_chars(struct uart_8250_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + ast25xx_uart_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + ast_serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static unsigned int check_modem_status(struct uart_8250_port *up) +{ + unsigned int status = ast_serial_in(up, UART_MSR); + + UART_DBG("line[%d]\n", up->port.line); + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI + && up->port.state != NULL) { + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, + status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, + status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); + } + + return status; +} + +/* + * This handles the interrupt from one port. + */ +static inline void ast25xx_uart_handle_port(struct uart_8250_port *up) +{ + unsigned int status; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + status = serial_inp(up, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * This is the serial driver's interrupt routine. + */ +static irqreturn_t ast_uart_interrupt(int irq, void *dev_id) +{ + struct irq_info *i = dev_id; + int pass_counter = 0, handled = 0, end = 0; + + DEBUG_INTR("(%d) ", irq); + spin_lock(&i->lock); + + do { + struct uart_8250_port *up; + unsigned int iir; + + up = (struct uart_8250_port *)(i->up); + + iir = ast_serial_in(up, UART_IIR); + if (!(iir & UART_IIR_NO_INT)) { + ast25xx_uart_handle_port(up); + handled = 1; + + } else + end = 1; + + if (pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + UART_DBG(KERN_ERR + "ast-uart-dma:too much work for irq%d\n", irq); + break; + } + } while (end); + + spin_unlock(&i->lock); + + DEBUG_INTR("end.\n"); + + return IRQ_RETVAL(handled); +} + +static unsigned int ast25xx_uart_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + unsigned int lsr; + + UART_TX_DBG("line[%d]\n", up->port.line); + + spin_lock_irqsave(&up->port.lock, flags); + lsr = ast_serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&up->port.lock, flags); + + return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0; +} + +static unsigned int ast25xx_uart_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned int status; + unsigned int ret; + + status = check_modem_status(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void ast25xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char mcr = 0; + + mctrl = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + ast_serial_out(up, UART_MCR, mcr); + +} + +static void ast25xx_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + ast_serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ast25xx_uart_startup(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + // TX DMA + struct circ_buf *xmit = &up->port.state->xmit; + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + unsigned char lsr, iir; + int retval; + int irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; + + UART_DBG("%s\n", __func__); + + priv->up = up; + + UART_DBG("line[%d]\n", port->line); + up->capabilities = uart_config[up->port.type].flags; + up->mcr = 0; + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + ast25xx_uart_clear_fifos(up); + /* + * Clear the interrupt registers. + */ + (void)serial_inp(up, UART_LSR); + (void)serial_inp(up, UART_RX); + (void)serial_inp(up, UART_IIR); + (void)serial_inp(up, UART_MSR); + + ast_uart_irq[0].up = up; + retval = request_irq(up->port.irq, ast_uart_interrupt, irq_flags, + "ast-uart-dma", ast_uart_irq); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl |= TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_outp(up, UART_IER, UART_IER_THRI); + lsr = ast_serial_in(up, UART_LSR); + iir = ast_serial_in(up, UART_IIR); + serial_outp(up, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + UART_DBG("ttyDMA%d - enabling bad tx status\n", + port->line); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_inp(up, UART_LSR); + serial_inp(up, UART_RX); + serial_inp(up, UART_IIR); + serial_inp(up, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + // RX DMA + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; + up->port.icount.rx = 0; + + priv->tx_done = 1; + priv->tx_count = 0; + + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; +#ifdef SDDMA_RX_FIX +#else + priv->workaround = 0; +#endif + // UART_DBG("Sending trigger for % x\n", priv->dma_ch); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); +#ifdef SDDMA_RX_FIX +#else + add_timer(&priv->rx_timer); +#endif + priv->tx_dma_buf.head = 0; + priv->tx_dma_buf.tail = 0; + priv->tx_dma_buf.buf = xmit->buf; + + UART_DBG("head:0x%x tail:0x%x\n", xmit->head, xmit->tail); + xmit->head = 0; + xmit->tail = 0; + + priv->dma_tx_addr = dma_map_single(port->dev, priv->tx_dma_buf.buf, + UART_XMIT_SIZE, DMA_TO_DEVICE); + + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_tx_sdma_enqueue(priv->dma_ch, priv->dma_tx_addr); + ast_uart_tx_sdma_update(priv->dma_ch, 0); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); + return 0; +} + +static void ast25xx_uart_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + + UART_DBG("line[%d]\n", port->line); + priv->up = NULL; + + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + ast_serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + ast25xx_uart_clear_fifos(up); + + (void)ast_serial_in(up, UART_RX); + + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); +#ifdef SDDMA_RX_FIX +#else + del_timer_sync(&up->rx_timer); +#endif + + // Tx buffer will free by serial_core.c + free_irq(up->port.irq, ast_uart_irq); +} + +static unsigned int ast25xx_uart_get_divisor(struct uart_port *port, + unsigned int baud) +{ + unsigned int quot; + + quot = uart_get_divisor(port, baud); + + return quot; +} + +static void ast25xx_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (termios->c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = ast25xx_uart_get_divisor(port, baud); + + if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) { + if (baud < 2400) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; + else + fcr = uart_config[up->port.type].fcr; + } + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + ast_serial_out(up, UART_IER, up->ier); + + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + + serial_dl_write(up, quot); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +/* + * Resource handling. + */ +static int ast25xx_uart_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + int ret = 0; + + if (!up->port.mapbase) + return ret; + + if (!request_mem_region(up->port.mapbase, size, "ast-uart-dma")) { + ret = -EBUSY; + return ret; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap_nocache(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + return ret; + } + } + return ret; +} + +static void ast25xx_uart_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + + if (!up->port.mapbase) + return; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); +} + +static void ast25xx_uart_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + ret = ast25xx_uart_request_std_resource(up); + if (ret == 0) + ast25xx_uart_release_std_resource(up); + + return ret; +} + +static void ast25xx_uart_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = ast25xx_uart_request_std_resource(up); + if (ret < 0) + return; + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + if (up->port.type == PORT_UNKNOWN) + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + return 0; +} + +static const char *ast25xx_uart_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + + + +static unsigned int ast25xx_uart_serial_in(struct uart_port *port, int offset) +{ + offset = offset << port->regshift; + return readb(port->membase + offset); + +} + + +static void ast25xx_uart_serial_out(struct uart_port *port, + int offset, int value) +{ + offset = offset << port->regshift; + writeb(value, port->membase + offset); +} + +static const struct uart_ops ast25xx_uart_pops = { + .tx_empty = ast25xx_uart_tx_empty, + .set_mctrl = ast25xx_uart_set_mctrl, + .get_mctrl = ast25xx_uart_get_mctrl, + .stop_tx = ast25xx_uart_stop_tx, + .start_tx = ast25xx_uart_start_tx, + .stop_rx = ast25xx_uart_stop_rx, + .enable_ms = ast25xx_uart_enable_ms, + .break_ctl = ast25xx_uart_break_ctl, + .startup = ast25xx_uart_startup, + .shutdown = ast25xx_uart_shutdown, + .set_termios = ast25xx_uart_set_termios, + .type = ast25xx_uart_type, + .release_port = ast25xx_uart_release_port, + .request_port = ast25xx_uart_request_port, + .config_port = ast25xx_uart_config_port, + .verify_port = ast25xx_uart_verify_port, +}; + + + +/* + * Register a set of serial devices attached to a platform device. The + * list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +struct clk *clk; + +static int ast25xx_uart_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct ast_uart_priv_data *priv; + struct uart_8250_port port_8250; + struct uart_8250_port *up; + int ret; + u32 read, dma_channel = 0; + struct resource *res; + + if (UART_XMIT_SIZE > DMA_BUFF_SIZE) + UART_DBG("UART_XMIT_SIZE > DMA_BUFF_SIZE : Please Check\n"); + + priv = (struct ast_uart_priv_data *)devm_kzalloc(&pdev->dev, + sizeof(struct ast_uart_priv_data), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + up = &port_8250; + memset(up, 0, sizeof(struct uart_8250_port)); + up->port.flags = UPF_IOREMAP; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res == NULL) { + dev_err(&pdev->dev, "IRQ resource not found"); + return -ENODEV; + } + up->port.irq = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Register base not found"); + return -ENODEV; + } + up->port.mapbase = res->start; + + ret = ast25xx_uart_request_std_resource(up); + if (ret) { + dev_err(&pdev->dev, "ioremap_nocache Failed"); + return ret; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + dev_err(&pdev->dev, "missing controller clock"); + + ret = clk_prepare_enable(clk); + if (ret) + dev_err(&pdev->dev, "failed to enable DMA UART Clk"); + + up->port.uartclk = clk_get_rate(clk); + + if (of_property_read_u32(np, "reg-shift", &read) == 0) + up->port.regshift = read; + if (of_property_read_u32(np, "dma-channel", &read) == 0) { + dma_channel = read; + priv->dma_ch = dma_channel; + } + up->port.iotype = UPIO_MEM; + up->port.flags |= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + up->port.dev = &pdev->dev; + if (share_irqs) + up->port.flags |= UPF_SHARE_IRQ; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->port.type = PORT_16550; + up->port.iotype = UPIO_MEM; + up->port.flags = UPF_FIXED_TYPE; + up->port.startup = ast25xx_uart_startup; + up->port.shutdown = ast25xx_uart_shutdown; + up->port.set_termios = ast25xx_uart_set_termios; + up->port.set_mctrl = ast25xx_uart_set_mctrl; + up->port.serial_in = ast25xx_uart_serial_in; + up->port.serial_out = ast25xx_uart_serial_out; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + up->capabilities |= UART_CAP_FIFO; + + up->port.private_data = priv; + + ret = serial8250_register_8250_port(up); + if (ret < 0) { + dev_err(&pdev->dev, + "unable to registr port (IO%lx MEM%llx IRQ%d):%d\n", + up->port.iobase, (unsigned long long)up->port.mapbase, + up->port.irq, ret); + return ret; + } + priv->line = ret; + + tasklet_init(&priv->tx_tasklet, ast_uart_tx_sdma_tasklet_func, + (unsigned long)priv); +#ifdef SDDMA_RX_FIX + tasklet_init(&priv->rx_tasklet, ast_uart_rx_sdma_tasklet_func, + (unsigned long)priv); +#else + uart->rx_timer.data = (unsigned long)port; + uart->rx_timer.expires = jiffies + (HZ); + uart->rx_timer.function = ast_uart_rx_timer_func; + init_timer(&priv->rx_timer); +#endif + +//DMA request +#ifdef SDDMA_RX_FIX + priv->rx_dma_buf.buf = + ast_uart_rx_sdma_request(priv->dma_ch, ast_uart_rx_buffdone, + priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; +} +#else + priv->rx_dma_buf.buf = ast_uart_rx_sdma_request( + priv->dma_ch, priv); + if (priv->rx_dma_buf.buf < 0) { + UART_DBG("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } +#endif + if (ast_uart_tx_sdma_request( + priv->dma_ch, ast_uart_tx_buffdone, priv) < 0) { + UART_DBG("Error : failed to get tx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } + + + platform_set_drvdata(pdev, priv); + return 0; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ast25xx_uart_remove(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_unregister_port(priv->line); + return 0; +} + +static int ast25xx_uart_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_suspend_port(priv->line); + return 0; +} + +static int ast25xx_uart_resume(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_resume_port(priv->line); + return 0; +} + +static const struct of_device_id ast_serial_dt_ids[] = { + { .compatible = "aspeed,ast-sdma-uart", }, + { /* sentinel */ } +}; + +static struct platform_driver ast25xx_uart_driver = { + .probe = ast25xx_uart_probe, + .remove = ast25xx_uart_remove, + .suspend = ast25xx_uart_suspend, + .resume = ast25xx_uart_resume, + .driver = { + .name = "ast-uart-dma", + .of_match_table = of_match_ptr(ast_serial_dt_ids), + }, +}; + +static int __init ast_uart_init(void) +{ + int ret; + + if (nr_uarts > UART_DMA_NR) + nr_uarts = UART_DMA_NR; + + ret = ast_uart_sdma_probe(); + if (ret) { + UART_DBG("ast_uart_sdma_probe Failed ret = %d\n", ret); + goto out; + } + UART_DBG(KERN_INFO + "ast-uart-dma:UART driver with DMA%d ports IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); + + spin_lock_init(&ast_uart_irq[0].lock); + + ret = platform_driver_register(&ast25xx_uart_driver); + if (ret == 0) + goto out; + +out: + return ret; +} + +static void __exit ast_uart_exit(void) +{ + + platform_driver_unregister(&ast25xx_uart_driver); + +} +module_init(ast_uart_init); +module_exit(ast_uart_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("AST DMA serial driver"); +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR); -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-10 16:49 ` Greg KH -1 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:49 UTC (permalink / raw) To: linux-aspeed On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > From: sudheer Kumar veliseti <sudheer.open@gmail.com> > > Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> > --- I can not take a patch without any changelog text at all, especially for one that is 1928 lines long :( Please provide a proper changelog and I will be glad to review it. thanks, greg k-h ^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [patch 1/5] AST2500 DMA UART driver @ 2019-06-10 16:49 ` Greg KH 0 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:49 UTC (permalink / raw) To: sudheer.v Cc: mark.rutland, devicetree, sudheer.veliseti, linux-aspeed, andrew, benh, shivahshankar.shankarnarayanrao, robh+dt, joel, linux-serial, jslaby, mchehab+samsung, linux-arm-kernel, sudheer Kumar veliseti On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > From: sudheer Kumar veliseti <sudheer.open@gmail.com> > > Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> > --- I can not take a patch without any changelog text at all, especially for one that is 1928 lines long :( Please provide a proper changelog and I will be glad to review it. thanks, greg k-h _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [patch 1/5] AST2500 DMA UART driver @ 2019-06-10 16:49 ` Greg KH 0 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:49 UTC (permalink / raw) To: sudheer.v Cc: mark.rutland, devicetree, sudheer.veliseti, linux-aspeed, andrew, benh, shivahshankar.shankarnarayanrao, robh+dt, joel, linux-serial, jslaby, mchehab+samsung, linux-arm-kernel, sudheer Kumar veliseti On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > From: sudheer Kumar veliseti <sudheer.open@gmail.com> > > Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> > --- I can not take a patch without any changelog text at all, especially for one that is 1928 lines long :( Please provide a proper changelog and I will be glad to review it. thanks, greg k-h ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-10 16:50 ` Greg KH -1 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:50 UTC (permalink / raw) To: linux-aspeed On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > + > +#define CONFIG_UART_DMA_DEBUG > + > +#ifdef CONFIG_UART_DMA_DEBUG > +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) > +#else > +#define UART_DBG(fmt, args...) > +#endif > + > +#define CONFIG_UART_TX_DMA_DEBUG 1 > + > +#ifdef CONFIG_UART_TX_DMA_DEBUG > +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) > +#else > +#define UART_TX_DBG(fmt, args...) > +#endif Why have you left debugging on here? Why does your tiny driver have custom debug macros? Please always use the in-kernel standard ones so you can dynamically enable/disable them as needed without having to rebuild the code. I stopped reading here, sorry. greg k-h ^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [patch 1/5] AST2500 DMA UART driver @ 2019-06-10 16:50 ` Greg KH 0 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:50 UTC (permalink / raw) To: sudheer.v Cc: mark.rutland, devicetree, sudheer.veliseti, linux-aspeed, andrew, benh, shivahshankar.shankarnarayanrao, robh+dt, joel, linux-serial, jslaby, mchehab+samsung, linux-arm-kernel, sudheer Kumar veliseti On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > + > +#define CONFIG_UART_DMA_DEBUG > + > +#ifdef CONFIG_UART_DMA_DEBUG > +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) > +#else > +#define UART_DBG(fmt, args...) > +#endif > + > +#define CONFIG_UART_TX_DMA_DEBUG 1 > + > +#ifdef CONFIG_UART_TX_DMA_DEBUG > +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) > +#else > +#define UART_TX_DBG(fmt, args...) > +#endif Why have you left debugging on here? Why does your tiny driver have custom debug macros? Please always use the in-kernel standard ones so you can dynamically enable/disable them as needed without having to rebuild the code. I stopped reading here, sorry. greg k-h _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [patch 1/5] AST2500 DMA UART driver @ 2019-06-10 16:50 ` Greg KH 0 siblings, 0 replies; 26+ messages in thread From: Greg KH @ 2019-06-10 16:50 UTC (permalink / raw) To: sudheer.v Cc: mark.rutland, devicetree, sudheer.veliseti, linux-aspeed, andrew, benh, shivahshankar.shankarnarayanrao, robh+dt, joel, linux-serial, jslaby, mchehab+samsung, linux-arm-kernel, sudheer Kumar veliseti On Wed, Jun 05, 2019 at 05:53:11PM +0530, sudheer.v wrote: > + > +#define CONFIG_UART_DMA_DEBUG > + > +#ifdef CONFIG_UART_DMA_DEBUG > +#define UART_DBG(fmt, args...) pr_debug("%s() " fmt, __func__, ## args) > +#else > +#define UART_DBG(fmt, args...) > +#endif > + > +#define CONFIG_UART_TX_DMA_DEBUG 1 > + > +#ifdef CONFIG_UART_TX_DMA_DEBUG > +#define UART_TX_DBG(fmt, args...) pr_debug("%s()"fmt, __func__, ## args) > +#else > +#define UART_TX_DBG(fmt, args...) > +#endif Why have you left debugging on here? Why does your tiny driver have custom debug macros? Please always use the in-kernel standard ones so you can dynamically enable/disable them as needed without having to rebuild the code. I stopped reading here, sorry. greg k-h ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 2/5] build configuration for AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-05 12:23 ` sudheer.v -1 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- drivers/tty/serial/8250/Kconfig | 35 +++++++++++++++++++++++++++++++- drivers/tty/serial/8250/Makefile | 1 + 2 files changed, 35 insertions(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 15c2c5463835..c793466a1c47 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -45,7 +45,7 @@ config SERIAL_8250_DEPRECATED_OPTIONS keep the 8250_core.* options around until they revert the changes they already did. - If 8250 is built as a module, this adds 8250_core alias instead. + If 8250 is built as a module, this adds 8250_core alias instead. If you did not notice yet and/or you have userspace from pre-3.7, it is safe (and recommended) to say N here. @@ -189,6 +189,39 @@ config SERIAL_8250_RUNTIME_UARTS with the module parameter "nr_uarts", or boot-time parameter 8250.nr_uarts +config AST_SERIAL_DMA_UART + tristate "AST UART driver with DMA" + select SERIAL_CORE + help + UART driver with DMA support for Aspeed BMC AST25XX. + this driver supports UARTs in AST2500,AST2600. It uses + DMA channel of DMA engines present in these chips. + since this dma engine is used only by UARTs it is not + added as a separate DMA driver instead added as a layer + within UART driver. + + +config AST_NR_DMA_UARTS + int "Maximum number of uart dma serial ports" + depends on AST_SERIAL_DMA_UART + default "4" + help + Set this to the number of serial ports you want the driver + to support. This includes any ports discovered via ACPI or + PCI enumeration and any ports that may be added at run-time + via hot-plug, or any ISA multi-port serial cards. + +config AST_RUNTIME_DMA_UARTS + int "Number of uart dma serial ports to register at runtime" + depends on AST_SERIAL_DMA_UART + range 0 AST_NR_DMA_UARTS + default "4" + help + Set this to the maximum number of serial ports you want + the kernel to register at boot time. This can be overridden + with the module parameter "nr_uarts", or boot-time parameter + 8250.nr_uarts + config SERIAL_8250_EXTENDED bool "Extended 8250/16550 serial driver options" depends on SERIAL_8250 diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index 18751bc63a84..54d40e5c6e2a 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -36,6 +36,7 @@ obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o obj-$(CONFIG_SERIAL_8250_MOXA) += 8250_moxa.o obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o +obj-$(CONFIG_AST_SERIAL_DMA_UART) += 8250_ast2500_uart_dma.o obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 2/5] build configuration for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- drivers/tty/serial/8250/Kconfig | 35 +++++++++++++++++++++++++++++++- drivers/tty/serial/8250/Makefile | 1 + 2 files changed, 35 insertions(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 15c2c5463835..c793466a1c47 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -45,7 +45,7 @@ config SERIAL_8250_DEPRECATED_OPTIONS keep the 8250_core.* options around until they revert the changes they already did. - If 8250 is built as a module, this adds 8250_core alias instead. + If 8250 is built as a module, this adds 8250_core alias instead. If you did not notice yet and/or you have userspace from pre-3.7, it is safe (and recommended) to say N here. @@ -189,6 +189,39 @@ config SERIAL_8250_RUNTIME_UARTS with the module parameter "nr_uarts", or boot-time parameter 8250.nr_uarts +config AST_SERIAL_DMA_UART + tristate "AST UART driver with DMA" + select SERIAL_CORE + help + UART driver with DMA support for Aspeed BMC AST25XX. + this driver supports UARTs in AST2500,AST2600. It uses + DMA channel of DMA engines present in these chips. + since this dma engine is used only by UARTs it is not + added as a separate DMA driver instead added as a layer + within UART driver. + + +config AST_NR_DMA_UARTS + int "Maximum number of uart dma serial ports" + depends on AST_SERIAL_DMA_UART + default "4" + help + Set this to the number of serial ports you want the driver + to support. This includes any ports discovered via ACPI or + PCI enumeration and any ports that may be added at run-time + via hot-plug, or any ISA multi-port serial cards. + +config AST_RUNTIME_DMA_UARTS + int "Number of uart dma serial ports to register at runtime" + depends on AST_SERIAL_DMA_UART + range 0 AST_NR_DMA_UARTS + default "4" + help + Set this to the maximum number of serial ports you want + the kernel to register at boot time. This can be overridden + with the module parameter "nr_uarts", or boot-time parameter + 8250.nr_uarts + config SERIAL_8250_EXTENDED bool "Extended 8250/16550 serial driver options" depends on SERIAL_8250 diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index 18751bc63a84..54d40e5c6e2a 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -36,6 +36,7 @@ obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o obj-$(CONFIG_SERIAL_8250_MOXA) += 8250_moxa.o obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o +obj-$(CONFIG_AST_SERIAL_DMA_UART) += 8250_ast2500_uart_dma.o obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 2/5] build configuration for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- drivers/tty/serial/8250/Kconfig | 35 +++++++++++++++++++++++++++++++- drivers/tty/serial/8250/Makefile | 1 + 2 files changed, 35 insertions(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 15c2c5463835..c793466a1c47 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -45,7 +45,7 @@ config SERIAL_8250_DEPRECATED_OPTIONS keep the 8250_core.* options around until they revert the changes they already did. - If 8250 is built as a module, this adds 8250_core alias instead. + If 8250 is built as a module, this adds 8250_core alias instead. If you did not notice yet and/or you have userspace from pre-3.7, it is safe (and recommended) to say N here. @@ -189,6 +189,39 @@ config SERIAL_8250_RUNTIME_UARTS with the module parameter "nr_uarts", or boot-time parameter 8250.nr_uarts +config AST_SERIAL_DMA_UART + tristate "AST UART driver with DMA" + select SERIAL_CORE + help + UART driver with DMA support for Aspeed BMC AST25XX. + this driver supports UARTs in AST2500,AST2600. It uses + DMA channel of DMA engines present in these chips. + since this dma engine is used only by UARTs it is not + added as a separate DMA driver instead added as a layer + within UART driver. + + +config AST_NR_DMA_UARTS + int "Maximum number of uart dma serial ports" + depends on AST_SERIAL_DMA_UART + default "4" + help + Set this to the number of serial ports you want the driver + to support. This includes any ports discovered via ACPI or + PCI enumeration and any ports that may be added at run-time + via hot-plug, or any ISA multi-port serial cards. + +config AST_RUNTIME_DMA_UARTS + int "Number of uart dma serial ports to register at runtime" + depends on AST_SERIAL_DMA_UART + range 0 AST_NR_DMA_UARTS + default "4" + help + Set this to the maximum number of serial ports you want + the kernel to register at boot time. This can be overridden + with the module parameter "nr_uarts", or boot-time parameter + 8250.nr_uarts + config SERIAL_8250_EXTENDED bool "Extended 8250/16550 serial driver options" depends on SERIAL_8250 diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index 18751bc63a84..54d40e5c6e2a 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -36,6 +36,7 @@ obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o obj-$(CONFIG_SERIAL_8250_MOXA) += 8250_moxa.o obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o +obj-$(CONFIG_AST_SERIAL_DMA_UART) += 8250_ast2500_uart_dma.o obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 3/5] DT nodes for AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-05 12:23 ` sudheer.v -1 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 +++++++ arch/arm/boot/dts/aspeed-g5.dtsi | 71 ++++++++++++++++++++++-- 2 files changed, 88 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed-ast2500-evb.dts index 5dbb33c10c4f..4da09fbe94df 100644 --- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts +++ b/arch/arm/boot/dts/aspeed-ast2500-evb.dts @@ -64,6 +64,27 @@ status = "okay"; }; +&ast_uart_sdma { + status = "okay"; +}; + +&dma_uart1 { + status = "okay"; +}; + +&dma_uart2 { + status = "okay"; +}; + +&dma_uart3 { + status = "okay"; +}; + +&dma_uart4 { + status = "okay"; +}; + + &mac0 { status = "okay"; diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi index 674746513031..fb7b3ed463de 100644 --- a/arch/arm/boot/dts/aspeed-g5.dtsi +++ b/arch/arm/boot/dts/aspeed-g5.dtsi @@ -23,10 +23,10 @@ i2c11 = &i2c11; i2c12 = &i2c12; i2c13 = &i2c13; - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; + serial0 = &dma_uart1; + serial1 = &dma_uart2; + serial2 = &dma_uart3; + serial3 = &dma_uart4; serial4 = &uart5; serial5 = &vuart; peci0 = &peci0; @@ -497,6 +497,69 @@ status = "disabled"; }; + ast_uart_sdma: uart_sdma at 1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; + + dma_uart1: dma_uart1 at 1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; + status = "disabled"; + }; + + dma_uart2: dma_uart2 at 1e78d000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78d000 0x1000>; + reg-shift = <2>; + interrupts = <32>; + clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>; + dma-channel = <1>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd2_default + &pinctrl_rxd2_default>; + status = "disabled"; + }; + + dma_uart3: dma_uart3 at 1e78e000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78e000 0x1000>; + reg-shift = <2>; + interrupts = <33>; + clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>; + dma-channel = <2>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd3_default + &pinctrl_rxd3_default>; + status = "disabled"; + }; + + dma_uart4: dma_uart4 at 1e78f000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78f000 0x1000>; + reg-shift = <2>; + interrupts = <34>; + clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>; + dma-channel = <3>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd4_default + &pinctrl_rxd4_default>; + status = "disabled"; + }; + i2c: bus at 1e78a000 { compatible = "simple-bus"; #address-cells = <1>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 3/5] DT nodes for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 +++++++ arch/arm/boot/dts/aspeed-g5.dtsi | 71 ++++++++++++++++++++++-- 2 files changed, 88 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed-ast2500-evb.dts index 5dbb33c10c4f..4da09fbe94df 100644 --- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts +++ b/arch/arm/boot/dts/aspeed-ast2500-evb.dts @@ -64,6 +64,27 @@ status = "okay"; }; +&ast_uart_sdma { + status = "okay"; +}; + +&dma_uart1 { + status = "okay"; +}; + +&dma_uart2 { + status = "okay"; +}; + +&dma_uart3 { + status = "okay"; +}; + +&dma_uart4 { + status = "okay"; +}; + + &mac0 { status = "okay"; diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi index 674746513031..fb7b3ed463de 100644 --- a/arch/arm/boot/dts/aspeed-g5.dtsi +++ b/arch/arm/boot/dts/aspeed-g5.dtsi @@ -23,10 +23,10 @@ i2c11 = &i2c11; i2c12 = &i2c12; i2c13 = &i2c13; - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; + serial0 = &dma_uart1; + serial1 = &dma_uart2; + serial2 = &dma_uart3; + serial3 = &dma_uart4; serial4 = &uart5; serial5 = &vuart; peci0 = &peci0; @@ -497,6 +497,69 @@ status = "disabled"; }; + ast_uart_sdma: uart_sdma@1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; + + dma_uart1: dma_uart1@1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; + status = "disabled"; + }; + + dma_uart2: dma_uart2@1e78d000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78d000 0x1000>; + reg-shift = <2>; + interrupts = <32>; + clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>; + dma-channel = <1>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd2_default + &pinctrl_rxd2_default>; + status = "disabled"; + }; + + dma_uart3: dma_uart3@1e78e000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78e000 0x1000>; + reg-shift = <2>; + interrupts = <33>; + clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>; + dma-channel = <2>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd3_default + &pinctrl_rxd3_default>; + status = "disabled"; + }; + + dma_uart4: dma_uart4@1e78f000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78f000 0x1000>; + reg-shift = <2>; + interrupts = <34>; + clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>; + dma-channel = <3>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd4_default + &pinctrl_rxd4_default>; + status = "disabled"; + }; + i2c: bus@1e78a000 { compatible = "simple-bus"; #address-cells = <1>; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 3/5] DT nodes for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 +++++++ arch/arm/boot/dts/aspeed-g5.dtsi | 71 ++++++++++++++++++++++-- 2 files changed, 88 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed-ast2500-evb.dts index 5dbb33c10c4f..4da09fbe94df 100644 --- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts +++ b/arch/arm/boot/dts/aspeed-ast2500-evb.dts @@ -64,6 +64,27 @@ status = "okay"; }; +&ast_uart_sdma { + status = "okay"; +}; + +&dma_uart1 { + status = "okay"; +}; + +&dma_uart2 { + status = "okay"; +}; + +&dma_uart3 { + status = "okay"; +}; + +&dma_uart4 { + status = "okay"; +}; + + &mac0 { status = "okay"; diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi index 674746513031..fb7b3ed463de 100644 --- a/arch/arm/boot/dts/aspeed-g5.dtsi +++ b/arch/arm/boot/dts/aspeed-g5.dtsi @@ -23,10 +23,10 @@ i2c11 = &i2c11; i2c12 = &i2c12; i2c13 = &i2c13; - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; + serial0 = &dma_uart1; + serial1 = &dma_uart2; + serial2 = &dma_uart3; + serial3 = &dma_uart4; serial4 = &uart5; serial5 = &vuart; peci0 = &peci0; @@ -497,6 +497,69 @@ status = "disabled"; }; + ast_uart_sdma: uart_sdma@1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; + + dma_uart1: dma_uart1@1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; + status = "disabled"; + }; + + dma_uart2: dma_uart2@1e78d000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78d000 0x1000>; + reg-shift = <2>; + interrupts = <32>; + clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>; + dma-channel = <1>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd2_default + &pinctrl_rxd2_default>; + status = "disabled"; + }; + + dma_uart3: dma_uart3@1e78e000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78e000 0x1000>; + reg-shift = <2>; + interrupts = <33>; + clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>; + dma-channel = <2>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd3_default + &pinctrl_rxd3_default>; + status = "disabled"; + }; + + dma_uart4: dma_uart4@1e78f000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e78f000 0x1000>; + reg-shift = <2>; + interrupts = <34>; + clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>; + dma-channel = <3>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd4_default + &pinctrl_rxd4_default>; + status = "disabled"; + }; + i2c: bus@1e78a000 { compatible = "simple-bus"; #address-cells = <1>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 4/5] defconfig and MAINTAINERS updated for AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-05 12:23 ` sudheer.v -1 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- MAINTAINERS | 13 +++++++++++++ arch/arm/configs/aspeed_g5_defconfig | 1 + 2 files changed, 14 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 997e27ab492f..c9a9790b97f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1347,6 +1347,19 @@ F: drivers/crypto/axis F: drivers/pinctrl/pinctrl-artpec* F: Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt +ARM/ASPEED DMA UART DRIVER +M: sudheer v <sudheer.open@gmail.com> +M: ShivahShankar <shivahshankar.shankarnarayanrao@aspeedtech.com> +R: Joel Stanley <joel@jms.id.au> +R: Andrew Jeffery <andrew@aj.id.au> +R: Vinod Koul <vkoul@kernel.org> +L: dmaengine at vger.kernel.org +L: openbmc at lists.ozlabs.org +L: linux-aspeed at lists.ozlabs.org +S: Maintained +F: drivers/tty/serial/8250/8250_aspeed_uart_dma.c +F: Documentation/devicetree/bindings/serial/ast-sdma-uart.txt + ARM/ASPEED I2C DRIVER M: Brendan Higgins <brendanhiggins@google.com> R: Benjamin Herrenschmidt <benh@kernel.crashing.org> diff --git a/arch/arm/configs/aspeed_g5_defconfig b/arch/arm/configs/aspeed_g5_defconfig index 1849cbc161b4..25bf26630939 100644 --- a/arch/arm/configs/aspeed_g5_defconfig +++ b/arch/arm/configs/aspeed_g5_defconfig @@ -144,6 +144,7 @@ CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=6 CONFIG_SERIAL_8250_RUNTIME_UARTS=6 +CONFIG_AST_SERIAL_DMA_UART=y CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_ASPEED_VUART=y CONFIG_SERIAL_8250_SHARE_IRQ=y -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 4/5] defconfig and MAINTAINERS updated for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- MAINTAINERS | 13 +++++++++++++ arch/arm/configs/aspeed_g5_defconfig | 1 + 2 files changed, 14 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 997e27ab492f..c9a9790b97f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1347,6 +1347,19 @@ F: drivers/crypto/axis F: drivers/pinctrl/pinctrl-artpec* F: Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt +ARM/ASPEED DMA UART DRIVER +M: sudheer v <sudheer.open@gmail.com> +M: ShivahShankar <shivahshankar.shankarnarayanrao@aspeedtech.com> +R: Joel Stanley <joel@jms.id.au> +R: Andrew Jeffery <andrew@aj.id.au> +R: Vinod Koul <vkoul@kernel.org> +L: dmaengine@vger.kernel.org +L: openbmc@lists.ozlabs.org +L: linux-aspeed@lists.ozlabs.org +S: Maintained +F: drivers/tty/serial/8250/8250_aspeed_uart_dma.c +F: Documentation/devicetree/bindings/serial/ast-sdma-uart.txt + ARM/ASPEED I2C DRIVER M: Brendan Higgins <brendanhiggins@google.com> R: Benjamin Herrenschmidt <benh@kernel.crashing.org> diff --git a/arch/arm/configs/aspeed_g5_defconfig b/arch/arm/configs/aspeed_g5_defconfig index 1849cbc161b4..25bf26630939 100644 --- a/arch/arm/configs/aspeed_g5_defconfig +++ b/arch/arm/configs/aspeed_g5_defconfig @@ -144,6 +144,7 @@ CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=6 CONFIG_SERIAL_8250_RUNTIME_UARTS=6 +CONFIG_AST_SERIAL_DMA_UART=y CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_ASPEED_VUART=y CONFIG_SERIAL_8250_SHARE_IRQ=y -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 4/5] defconfig and MAINTAINERS updated for AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- MAINTAINERS | 13 +++++++++++++ arch/arm/configs/aspeed_g5_defconfig | 1 + 2 files changed, 14 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 997e27ab492f..c9a9790b97f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1347,6 +1347,19 @@ F: drivers/crypto/axis F: drivers/pinctrl/pinctrl-artpec* F: Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt +ARM/ASPEED DMA UART DRIVER +M: sudheer v <sudheer.open@gmail.com> +M: ShivahShankar <shivahshankar.shankarnarayanrao@aspeedtech.com> +R: Joel Stanley <joel@jms.id.au> +R: Andrew Jeffery <andrew@aj.id.au> +R: Vinod Koul <vkoul@kernel.org> +L: dmaengine@vger.kernel.org +L: openbmc@lists.ozlabs.org +L: linux-aspeed@lists.ozlabs.org +S: Maintained +F: drivers/tty/serial/8250/8250_aspeed_uart_dma.c +F: Documentation/devicetree/bindings/serial/ast-sdma-uart.txt + ARM/ASPEED I2C DRIVER M: Brendan Higgins <brendanhiggins@google.com> R: Benjamin Herrenschmidt <benh@kernel.crashing.org> diff --git a/arch/arm/configs/aspeed_g5_defconfig b/arch/arm/configs/aspeed_g5_defconfig index 1849cbc161b4..25bf26630939 100644 --- a/arch/arm/configs/aspeed_g5_defconfig +++ b/arch/arm/configs/aspeed_g5_defconfig @@ -144,6 +144,7 @@ CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=6 CONFIG_SERIAL_8250_RUNTIME_UARTS=6 +CONFIG_AST_SERIAL_DMA_UART=y CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_ASPEED_VUART=y CONFIG_SERIAL_8250_SHARE_IRQ=y -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 5/5] Documentation: DT bindings AST2500 DMA UART driver 2019-06-05 12:23 ` sudheer.v (?) @ 2019-06-05 12:23 ` sudheer.v -1 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: linux-aspeed From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../bindings/serial/ast2500-dma-uart.txt | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt diff --git a/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt new file mode 100644 index 000000000000..ff9bb6146bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt @@ -0,0 +1,40 @@ + +node for DMA controller: + ast_uart_sdma: uart_sdma at 1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; +this node doesn't binds with any driver. +DMA controller is handled as a separate SW layer,and is included in the same driver. +This DMA controller node is included in DT just for Register and interrupt details + + + +node for DMA-UART : + + +Required properties: + +- compatible: "aspeed,ast-sdma-uart" +- reg: The base address of the UART register bank +- interrupts: should contain interrupt specifier. +- clocks: Clock driving the hardware; +- pinctrl-0 : list of pinconfigurations +- dma-channel: channel of DMA-controller which is used + +Example: + + dma_uart1: dma_uart1 at 1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>; + status = "disabled"; + }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 5/5] Documentation: DT bindings AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../bindings/serial/ast2500-dma-uart.txt | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt diff --git a/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt new file mode 100644 index 000000000000..ff9bb6146bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt @@ -0,0 +1,40 @@ + +node for DMA controller: + ast_uart_sdma: uart_sdma@1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; +this node doesn't binds with any driver. +DMA controller is handled as a separate SW layer,and is included in the same driver. +This DMA controller node is included in DT just for Register and interrupt details + + + +node for DMA-UART : + + +Required properties: + +- compatible: "aspeed,ast-sdma-uart" +- reg: The base address of the UART register bank +- interrupts: should contain interrupt specifier. +- clocks: Clock driving the hardware; +- pinctrl-0 : list of pinconfigurations +- dma-channel: channel of DMA-controller which is used + +Example: + + dma_uart1: dma_uart1@1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>; + status = "disabled"; + }; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 5/5] Documentation: DT bindings AST2500 DMA UART driver @ 2019-06-05 12:23 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-05 12:23 UTC (permalink / raw) To: gregkh, mchehab+samsung, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, sudheer.veliseti Cc: devicetree, linux-aspeed, linux-serial, linux-arm-kernel, sudheer Kumar veliseti From: sudheer Kumar veliseti <sudheer.open@gmail.com> Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../bindings/serial/ast2500-dma-uart.txt | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt diff --git a/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt new file mode 100644 index 000000000000..ff9bb6146bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt @@ -0,0 +1,40 @@ + +node for DMA controller: + ast_uart_sdma: uart_sdma@1e79e000 { + compatible = "aspeed,ast-uart-sdma"; + reg = <0x1e79e000 0x400>; + interrupts = <50>; + status = "disabled"; + }; +this node doesn't binds with any driver. +DMA controller is handled as a separate SW layer,and is included in the same driver. +This DMA controller node is included in DT just for Register and interrupt details + + + +node for DMA-UART : + + +Required properties: + +- compatible: "aspeed,ast-sdma-uart" +- reg: The base address of the UART register bank +- interrupts: should contain interrupt specifier. +- clocks: Clock driving the hardware; +- pinctrl-0 : list of pinconfigurations +- dma-channel: channel of DMA-controller which is used + +Example: + + dma_uart1: dma_uart1@1e783000{ + compatible = "aspeed,ast-sdma-uart"; + reg = <0x1e783000 0x1000>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; + dma-channel = <0>; + no-loopback-test; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>; + status = "disabled"; + }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 0/5] *** DMA based UART driver for AST2500 *** @ 2019-06-21 11:17 sudheer.v 2019-06-21 11:17 ` sudheer.v 0 siblings, 1 reply; 26+ messages in thread From: sudheer.v @ 2019-06-21 11:17 UTC (permalink / raw) To: linux-aspeed From: sudheer veliseti <sudheer.open@gmail.com> Hi, AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. Thanks and Regards Sudheer.V sudheer veliseti (5): AST2500 DMA UART driver build configuration for AST2500 DMA UART driver DT nodes for AST2500 DMA UART driver defconfig and MAINTAINERS updated for AST2500 DMA UART driver Documentation: DT bindings AST2500 DMA UART driver .../bindings/serial/ast2500-dma-uart.txt | 40 + MAINTAINERS | 13 + arch/arm/boot/dts/aspeed-ast2500-evb.dts | 21 + arch/arm/boot/dts/aspeed-g5.dtsi | 71 +- arch/arm/configs/aspeed_g5_defconfig | 1 + .../tty/serial/8250/8250_ast2500_uart_dma.c | 1879 +++++++++++++++++ drivers/tty/serial/8250/Kconfig | 35 +- drivers/tty/serial/8250/Makefile | 1 + 8 files changed, 2056 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/ast2500-dma-uart.txt create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c -- 2.17.1 ^ permalink raw reply [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver 2019-06-21 11:17 [patch 0/5] *** DMA based UART driver for AST2500 *** sudheer.v @ 2019-06-21 11:17 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-21 11:17 UTC (permalink / raw) To: linux-aspeed From: sudheer veliseti <sudheer.open@gmail.com> UART driver for Aspeed's bmc chip AST2500 Design approch: AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. implementation details: 'struct uart_8250_port' serial port is populated and registered with 8250_core. Rx and Tx dma channels are requested from DMA controller software Layer, which is part of uart driver itself. Interrupt service routine for DMA controller is the crucial one for Handling all the tx and rx data. ISRs installed for individual uarts are just dummy,and are helpful only to report any spurious interrupts in hardware. Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../tty/serial/8250/8250_ast2500_uart_dma.c | 1879 +++++++++++++++++ 1 file changed, 1879 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c diff --git a/drivers/tty/serial/8250/8250_ast2500_uart_dma.c b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c new file mode 100644 index 000000000000..13911a0a745a --- /dev/null +++ b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c @@ -0,0 +1,1879 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DMA UART Driver for ASPEED BMC chip: AST2500 + * + * Copyright (C) 2019 sudheer Kumar veliseti, Aspeed technology Inc. + * <open.sudheer@gmail.com> + * + */ +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/mutex.h> +#include <linux/nmi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#include "8250.h" + +#define DMA_BUFF_SIZE 0x1000 // 4096 +#define SDMA_RX_BUFF_SIZE 0x10000 // 65536 + +#define SDDMA_RX_FIX 1 +/* enum ast_uart_chan_op + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state + */ + +enum ast_uart_chan_op { + AST_UART_DMAOP_TRIGGER, + AST_UART_DMAOP_STOP, + AST_UART_DMAOP_PAUSE, +}; + +/* ast_uart_dma_cbfn_t * * buffer callback routine type */ +typedef void (*ast_uart_dma_cbfn_t)(void *dev_id, u16 len); + +struct ast_sdma_info { + u8 ch_no; + u8 direction; + u8 enable; + void *priv; + char *sdma_virt_addr; + dma_addr_t dma_phy_addr; + /* cdriver callbacks */ + ast_uart_dma_cbfn_t callback_fn; /* buffer done callback */ +}; + +#define AST_UART_SDMA_CH 12 + +struct ast_sdma_ch { + struct ast_sdma_info tx_dma_info[AST_UART_SDMA_CH]; + struct ast_sdma_info rx_dma_info[AST_UART_SDMA_CH]; +}; + +struct ast_sdma { + void __iomem *reg_base; + int dma_irq; + struct ast_sdma_ch *dma_ch; + struct regmap *map; +}; + + + +#define UART_TX_SDMA_EN 0x00 +#define UART_RX_SDMA_EN 0x04 +#define UART_SDMA_CONF 0x08 +#define UART_SDMA_TIMER 0x0C +#define UART_TX_SDMA_REST 0x20 +#define UART_RX_SDMA_REST 0x24 +#define UART_TX_SDMA_IER 0x30 +#define UART_TX_SDMA_ISR 0x34 +#define UART_RX_SDMA_IER 0x38 +#define UART_RX_SDMA_ISR 0x3C +#define UART_TX_R_POINT(x) (0x40 + (x * 0x20)) +#define UART_TX_W_POINT(x) (0x44 + (x * 0x20)) +#define UART_TX_SDMA_ADDR(x) (0x48 + (x * 0x20)) +#define UART_RX_R_POINT(x) (0x50 + (x * 0x20)) +#define UART_RX_W_POINT(x) (0x54 + (x * 0x20)) +#define UART_RX_SDMA_ADDR(x) (0x58 + (x * 0x20)) + +/* UART_TX_SDMA_EN-0x00 : UART TX DMA Enable */ +/* UART_RX_SDMA_EN-0x04 : UART RX DMA Enable */ +#define SDMA_CH_EN(x) (0x1 << (x)) + +/* UART_SDMA_CONF - 0x08 : Misc, Buffer size */ +#define SDMA_TX_BUFF_SIZE_MASK (0x3) +#define SDMA_SET_TX_BUFF_SIZE(x) (x) +#define SDMA_BUFF_SIZE_1KB (0x0) +#define SDMA_BUFF_SIZE_4KB (0x1) +#define SDMA_BUFF_SIZE_16KB (0x2) +#define SDMA_BUFF_SIZE_64KB (0x3) +#define SDMA_RX_BUFF_SIZE_MASK (0x3 << 2) +#define SDMA_SET_RX_BUFF_SIZE(x) (x << 2) +#define SDMA_TIMEOUT_DIS (0x1 << 4) + +/* UART_SDMA_TIMER-0x0C : UART DMA time out timer */ + +/* UART_TX_SDMA_IER 0x30 */ +/* UART_TX_SDMA_ISR 0x34 */ + +#define UART_SDMA11_INT (1 << 11) +#define UART_SDMA10_INT (1 << 10) +#define UART_SDMA9_INT (1 << 9) +#define UART_SDMA8_INT (1 << 8) +#define UART_SDMA7_INT (1 << 7) +#define UART_SDMA6_INT (1 << 6) +#define UART_SDMA5_INT (1 << 5) +#define UART_SDMA4_INT (1 << 4) +#define UART_SDMA3_INT (1 << 3) +#define UART_SDMA2_INT (1 << 2) +#define UART_SDMA1_INT (1 << 1) +#define UART_SDMA0_INT (1 << 0) + + +/* + * Configuration: + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option + * is unsafe when used on edge-triggered interrupts. + */ +static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; + +static unsigned int nr_uarts = CONFIG_AST_RUNTIME_DMA_UARTS; + + +#define PASS_LIMIT 256 + +#include <asm/serial.h> + +#define UART_DMA_NR CONFIG_AST_NR_DMA_UARTS + + +struct ast_uart_priv_data { + + unsigned short line; //index of uart port + struct uart_8250_port *up; + u8 dma_ch; // dma channel number + struct circ_buf rx_dma_buf; + struct circ_buf tx_dma_buf; + dma_addr_t dma_rx_addr; /* Mapped ADMA descr. table */ + dma_addr_t dma_tx_addr; /* Mapped ADMA descr. table */ +#ifdef SDDMA_RX_FIX + struct tasklet_struct rx_tasklet; +#else + struct timer_list rx_timer; +#endif + struct tasklet_struct tx_tasklet; + spinlock_t lock; + int tx_done; + int tx_count; +}; + + +static inline struct uart_8250_port * +to_uart_8250_port(struct uart_port *uart) { + return container_of(uart, struct uart_8250_port, port); +} + +struct irq_info { + spinlock_t lock; + struct uart_8250_port *up; +}; + +static struct irq_info ast_uart_irq[1]; +static DEFINE_MUTEX(ast_uart_mutex); + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 + | UART_FCR_DMA_SELECT, + .flags = UART_CAP_FIFO, + }, +}; + +/* sane hardware needs no mapping */ +#define map_8250_in_reg(up, offset) (offset) +#define map_8250_out_reg(up, offset) (offset) + +// SDMA - software Layer : (previously was in ast-uart-sdma.c) +static inline void ast_uart_sdma_write(struct ast_sdma *sdma, + u32 val, u32 reg) +{ + pr_debug("uart dma write:val:%x,reg:%x\n", val, reg); + writel(val, sdma->reg_base + reg); +} + +static inline u32 ast_uart_sdma_read(struct ast_sdma *sdma, u32 reg) +{ + return readl(sdma->reg_base + reg); +} + +struct ast_sdma ast_uart_sdma; + +int ast_uart_rx_sdma_enqueue(u8 ch, dma_addr_t rx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("ch = %d, rx buff = %x\n", ch, rx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, rx_buff, UART_RX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_tx_sdma_enqueue(u8 ch, dma_addr_t tx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("ch = %d, tx buff = %x\n", ch, tx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, tx_buff, UART_TX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + pr_debug("Trigger\n"); + dma_ch->enable = 1; +#ifdef SDDMA_RX_FIX +#else + ast_uart_set_sdma_time_out(0xffff); +#endif + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) | (0x1 << ch), + UART_RX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + // disable engine + pr_debug("STOP\n"); + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) | + (0x1 << ch), + UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) & + ~(0x1 << ch), + UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(ch)); + ast_uart_sdma_write(sdma, dma_ch->dma_phy_addr, UART_RX_SDMA_ADDR(ch)); + break; + case AST_UART_DMAOP_PAUSE: + // disable engine + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + break; + } + + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + pr_debug("TX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + pr_debug("TRIGGER : Enable\n"); + dma_ch->enable = 1; + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) | (0x1 << ch), + UART_TX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + pr_debug("STOP : DISABLE & RESET\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) | + (0x1 << ch), + UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) & + ~(0x1 << ch), + UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(ch)); + break; + case AST_UART_DMAOP_PAUSE: + pr_debug("PAUSE : DISABLE\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + } + + local_irq_restore(flags); + return 0; +} + +u32 ast_uart_get_tx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_TX_R_POINT(ch)); +} + +int ast_uart_tx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("TX DMA CTRL [ch %d] point %d\n", ch, point); + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_TX_W_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + pr_debug("TX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_IER) | (1 << ch), + UART_TX_SDMA_IER); + + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("RX DMA CTRL [ch %d] point %x\n", ch, point); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_RX_R_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +#ifdef SDDMA_RX_FIX +char *ast_uart_rx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return 0; + } + dma_ch->priv = id; + + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_IER) | (1 << ch), + UART_RX_SDMA_IER); + + local_irq_restore(flags); + + return dma_ch->sdma_virt_addr; +} + +#else +char *ast_uart_rx_sdma_request(u8 ch, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + + local_irq_restore(flags); + return dma_ch->sdma_virt_addr; +} +#endif + +u16 ast_uart_get_rx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_RX_W_POINT(ch)); +} + +void ast_uart_set_sdma_time_out(u16 val) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + ast_uart_sdma_write(sdma, val, UART_SDMA_TIMER); +} + +static inline void ast_sdma_bufffdone(struct ast_sdma_info *sdma_ch) +{ + u32 len; + struct ast_sdma *sdma = &ast_uart_sdma; + + if (sdma_ch->enable == 0) { + pr_debug("sdma Please check ch_no %x %s!!!!!\n", + sdma_ch->ch_no, sdma_ch->direction ? "TX" : "RX"); + if (sdma_ch->direction) { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) + & ~(0x1 << sdma_ch->ch_no), UART_TX_SDMA_EN); + } else { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << sdma_ch->ch_no), UART_RX_SDMA_EN); + ast_uart_rx_sdma_update(sdma_ch->ch_no, + ast_uart_get_rx_sdma_pt(sdma_ch->ch_no)); + pr_debug("OFFSET : UART_RX_SDMA_EN = %x\n ", + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN)); + } + return; + } + + if (sdma_ch->direction) { + len = ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)); + pr_debug("tx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_TX_W_POINT(sdma_ch->ch_no)) + ); + } else { + pr_debug("rx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_RX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)) + ); + len = ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)); + } + + pr_debug("<dma dwn>: ch[%d] : %s ,len : %d\n", sdma_ch->ch_no, + sdma_ch->direction ? "tx" : "rx", len); + + if (sdma_ch->callback_fn != NULL) + (sdma_ch->callback_fn)(sdma_ch->priv, len); +} + +static irqreturn_t ast_uart_sdma_isr(int irq, void *dev_id) +{ + struct ast_sdma *sdma = (struct ast_sdma *)dev_id; + + u32 tx_sts = ast_uart_sdma_read(sdma, UART_TX_SDMA_ISR); + u32 rx_sts = ast_uart_sdma_read(sdma, UART_RX_SDMA_ISR); + + pr_debug("tx sts : %x, rx sts : %x\n", tx_sts, rx_sts); + + if ((tx_sts == 0) && (rx_sts == 0)) { + pr_debug("SDMA IRQ ERROR !!!\n"); + return IRQ_HANDLED; + } + + if (rx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[0])); + } else if (rx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[1])); + } else if (rx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[2])); + } else if (rx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[3])); + } else if (rx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[4])); + } else if (rx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[5])); + } else if (rx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[6])); + } else if (rx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[7])); + } else if (rx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[8])); + } else if (rx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[9])); + } else if (rx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[10])); + } else if (rx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[11])); + } else { + + } + + if (tx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[0])); + } else if (tx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[1])); + } else if (tx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[2])); + } else if (tx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[3])); + } else if (tx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[4])); + } else if (tx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[5])); + } else if (tx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[6])); + } else if (tx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[7])); + } else if (tx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[8])); + } else if (tx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[9])); + } else if (tx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[10])); + } else if (tx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[11])); + } else { + } + + return IRQ_HANDLED; +} + +static int ast_uart_sdma_probe(void) +{ + int i; + struct device_node *node; + int ret; + struct ast_sdma *sdma = &ast_uart_sdma; + char *rx_dma_virt_addr; + dma_addr_t rx_dma_phy_addr; + + sdma->dma_ch = kzalloc(sizeof(struct ast_sdma_ch), GFP_KERNEL); + if (!sdma->dma_ch) + return -ENOMEM; + + // sdma memory mapping + node = of_find_compatible_node(NULL, NULL, "aspeed,ast-uart-sdma"); + if (!node) + return -ENODEV; + + sdma->reg_base = of_iomap(node, 0); + if (IS_ERR(sdma->reg_base)) + return PTR_ERR(sdma->map); + rx_dma_virt_addr = dma_alloc_coherent(NULL, + SDMA_RX_BUFF_SIZE * AST_UART_SDMA_CH, &rx_dma_phy_addr, GFP_KERNEL); + + if (!rx_dma_virt_addr) { + pr_debug("rx_dma_virt_addr Err:dma alloc Failed\n"); + return -ENOMEM; + } + for (i = 0; i < AST_UART_SDMA_CH; i++) { + // TX ------------------------ + sdma->dma_ch->tx_dma_info[i].enable = 0; + sdma->dma_ch->tx_dma_info[i].ch_no = i; + sdma->dma_ch->tx_dma_info[i].direction = 1; + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(i)); + // RX ------------------------ + sdma->dma_ch->rx_dma_info[i].enable = 0; + sdma->dma_ch->rx_dma_info[i].ch_no = i; + sdma->dma_ch->rx_dma_info[i].direction = 0; + sdma->dma_ch->rx_dma_info[i].sdma_virt_addr = + rx_dma_virt_addr + (SDMA_RX_BUFF_SIZE * i); + sdma->dma_ch->rx_dma_info[i].dma_phy_addr = + rx_dma_phy_addr + (SDMA_RX_BUFF_SIZE * i); + ast_uart_sdma_write(sdma, + sdma->dma_ch->rx_dma_info[i].dma_phy_addr, + UART_RX_SDMA_ADDR(i)); + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(i)); + } + + ast_uart_sdma_write(sdma, 0xffffffff, UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0xffffffff, UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_EN); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_EN); + +#ifdef SDDMA_RX_FIX + ast_uart_sdma_write(sdma, 0x200, UART_SDMA_TIMER); +#else + ast_uart_sdma_write(sdma, 0xffff, UART_SDMA_TIMER); +#endif + + // TX + ast_uart_sdma_write(sdma, 0xfff, UART_TX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_IER); + + // RX + ast_uart_sdma_write(sdma, 0xfff, UART_RX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_IER); + + sdma->dma_irq = of_irq_get(node, 0); + ret = request_irq(sdma->dma_irq, ast_uart_sdma_isr, 0, + "sdma-intr", sdma); + if (ret) { + pr_debug("Unable to get UART SDMA IRQ %x\n", ret); + return -ENODEV; + } + + ast_uart_sdma_write(sdma, SDMA_SET_TX_BUFF_SIZE(SDMA_BUFF_SIZE_4KB) | + SDMA_SET_RX_BUFF_SIZE(SDMA_BUFF_SIZE_64KB), + UART_SDMA_CONF); + return 0; +} + +// END of SDMA Layer + +// UART Driver Layer + +static unsigned int ast_serial_in(struct uart_8250_port *up, int offset) +{ + offset = map_8250_in_reg(up, offset) << up->port.regshift; + return readb(up->port.membase + offset); +} + +static void ast_serial_out(struct uart_8250_port *up, int offset, int value) +{ + /* Save the offset before it's remapped */ + offset = map_8250_out_reg(up, offset) << up->port.regshift; + writeb(value, up->port.membase + offset); +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) ast_serial_in(up, offset) +#define serial_outp(up, offset, value) ast_serial_out(up, offset, value) + +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) + +static void ast_uart_tx_sdma_tasklet_func(unsigned long data) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit = NULL; + u32 tx_pt; + + + if (!up) + return; + xmit = &up->port.state->xmit; + spin_lock(&up->port.lock); + priv->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); + dma_sync_single_for_device(up->port.dev, priv->dma_tx_addr, + UART_XMIT_SIZE, DMA_TO_DEVICE); + tx_pt = ast_uart_get_tx_sdma_pt(priv->dma_ch); + + if (tx_pt > xmit->head) { + if ((tx_pt & 0xfffc) == 0) + ast_uart_tx_sdma_update(priv->dma_ch, 0xffff); + else + ast_uart_tx_sdma_update(priv->dma_ch, 0); + } else { + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + } + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + spin_unlock(&up->port.lock); +} + +static void ast_uart_tx_buffdone(void *dev_id, u16 len) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit; + + if (!up) + return; + xmit = &(up->port.state->xmit); + + pr_debug("line[%d] : tx len = % d\n", priv->line, len); + spin_lock(&up->port.lock); + xmit->tail = len; + pr_debug(" line[%d], xmit->head = %d, xmit->tail = % d\n", + priv->line, xmit->head, xmit->tail); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (xmit->head != xmit->tail) + tasklet_schedule(&priv->tx_tasklet); + + spin_unlock(&up->port.lock); +} + +#ifdef SDDMA_RX_FIX +static void ast_uart_rx_sdma_tasklet_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct tty_port *ttyport; + int count; + int copy = 0; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + + ttyport = &up->port.state->port; + + pr_debug("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + spin_lock(&up->port.lock); + if (rx_ring->head > rx_ring->tail) { + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + } + + if (copy != count) + pr_debug(" !!!!!!!!ERROR 111\n"); + if (count) { + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + up->port.icount.rx += count; + tty_flip_buffer_push(ttyport); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + } + spin_unlock(&up->port.lock); +} + +static void ast_uart_rx_buffdone(void *dev_id, u16 len) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + pr_debug("line[%d], head = %d,len:%d\n", + priv->line, priv->rx_dma_buf.head, len); + spin_lock(&up->port.lock); + rx_ring->head = len; + spin_unlock(&up->port.lock); + tasklet_schedule(&priv->rx_tasklet); +} + +#else +static void ast_uart_rx_timer_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct tty_port *ttyport; + struct circ_buf *rx_ring; + struct tty_struct *tty; + char flag; + int count; + int copy; + + + if (!up) + return; + ttyport = &up->port.state->port; + rx_ring = &up->rx_dma_buf; + tty = up->port.state->port.tty; + + pr_debug("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + rx_ring->head = ast_uart_get_rx_sdma_pt(priv->dma_ch); + del_timer(&up->rx_timer); + + if (rx_ring->head > rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + // pr_debug("@@--%s-- ch = 0x%x\n", __func__, ch); + } + + if (copy != count) + pr_debug(" !!!!!!!!ERROR 111\n"); + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + + if (count) { + //pr_debug("\n count = % d\n", count); + up->port.icount.rx += count; + spin_lock(&up->port.lock); + tty_flip_buffer_push(ttyport); + spin_unlock(&up->port.lock); + //pr_debug("update rx_ring->tail % x\n", rx_ring->tail); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + priv->workaround = 1; + } else { + if (priv->workaround) { + priv->workaround++; + if (priv->workaround > 1) + ast_uart_set_sdma_time_out(0); + else + ast_uart_set_sdma_time_out(0xffff); + } + } + add_timer(&up->rx_timer); +} +#endif + +/* + * FIFO support. + */ +static inline void ast25xx_uart_clear_fifos(struct uart_8250_port *p) +{ + serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(p, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(p, UART_FCR, 0); +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned long flags; + + pr_debug("line[%d]\n", up->port.line); + if (!up->port.iobase && !up->port.mapbase && !up->port.membase) + return; + + pr_debug("ttyDMA%d : autoconf (0x%04lx, 0x%p) : ", up->port.line, + up->port.iobase, up->port.membase); + + spin_lock_irqsave(&up->port.lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + + if (up->port.type == PORT_UNKNOWN) + goto out; + + /* + * Reset the UART. + */ + ast25xx_uart_clear_fifos(up); + ast_serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); + pr_debug("type=%s\n", uart_config[up->port.type].name); +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + ast_serial_out(p, UART_IER, p->ier); + } +} + +static void ast25xx_uart_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", up->port.line); + __stop_tx(up); +} + +static void transmit_chars(struct uart_8250_port *up); + +static void ast25xx_uart_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + + pr_debug("line[%d]\n", port->line); + tasklet_schedule(&priv->tx_tasklet); +} + +static void ast25xx_uart_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", port->line); + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + ast_serial_out(up, UART_IER, up->ier); +} + +static void ast25xx_uart_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", port->line); + up->ier |= UART_IER_MSI; + ast_serial_out(up, UART_IER, up->ier); +} + +static void transmit_chars(struct uart_8250_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + ast25xx_uart_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + ast_serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static unsigned int check_modem_status(struct uart_8250_port *up) +{ + unsigned int status = ast_serial_in(up, UART_MSR); + + pr_debug("line[%d]\n", up->port.line); + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI + && up->port.state != NULL) { + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, + status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, + status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); + } + + return status; +} + +/* + * This handles the interrupt from one port. + */ +static inline void ast25xx_uart_handle_port(struct uart_8250_port *up) +{ + unsigned int status; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + status = serial_inp(up, UART_LSR); + + pr_debug("status = %x\n", status); + + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * This is the serial driver's interrupt routine. + */ +static irqreturn_t ast_uart_interrupt(int irq, void *dev_id) +{ + struct irq_info *i = dev_id; + int pass_counter = 0, handled = 0, end = 0; + + pr_debug("(%d)-", irq); + spin_lock(&i->lock); + + do { + struct uart_8250_port *up; + unsigned int iir; + + up = (struct uart_8250_port *)(i->up); + + iir = ast_serial_in(up, UART_IIR); + if (!(iir & UART_IIR_NO_INT)) { + ast25xx_uart_handle_port(up); + handled = 1; + + } else + end = 1; + + if (pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + pr_err("ast-uart-dma:too much work for irq%d\n", irq); + break; + } + } while (end); + + spin_unlock(&i->lock); + + pr_debug("-(%d)\n", irq); + + return IRQ_RETVAL(handled); +} + +static unsigned int ast25xx_uart_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + unsigned int lsr; + + pr_debug("line[%d]\n", up->port.line); + + spin_lock_irqsave(&up->port.lock, flags); + lsr = ast_serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&up->port.lock, flags); + + return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0; +} + +static unsigned int ast25xx_uart_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned int status; + unsigned int ret; + + status = check_modem_status(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void ast25xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char mcr = 0; + + mctrl = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + ast_serial_out(up, UART_MCR, mcr); + +} + +static void ast25xx_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + ast_serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ast25xx_uart_startup(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + // TX DMA + struct circ_buf *xmit = &up->port.state->xmit; + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + unsigned char lsr, iir; + int retval; + int irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; + + priv->up = up; + pr_debug("line[%d]\n", port->line); + up->capabilities = uart_config[up->port.type].flags; + up->mcr = 0; + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + ast25xx_uart_clear_fifos(up); + /* + * Clear the interrupt registers. + */ + (void)serial_inp(up, UART_LSR); + (void)serial_inp(up, UART_RX); + (void)serial_inp(up, UART_IIR); + (void)serial_inp(up, UART_MSR); + + ast_uart_irq[0].up = up; + retval = request_irq(up->port.irq, ast_uart_interrupt, irq_flags, + "ast-uart-dma", ast_uart_irq); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl |= TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_outp(up, UART_IER, UART_IER_THRI); + lsr = ast_serial_in(up, UART_LSR); + iir = ast_serial_in(up, UART_IIR); + serial_outp(up, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + pr_debug("ttyDMA%d-enabling bad tx status\n", + port->line); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_inp(up, UART_LSR); + serial_inp(up, UART_RX); + serial_inp(up, UART_IIR); + serial_inp(up, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + // RX DMA + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; + up->port.icount.rx = 0; + + priv->tx_done = 1; + priv->tx_count = 0; + + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; +#ifdef SDDMA_RX_FIX +#else + priv->workaround = 0; +#endif + // pr_debug("Sending trigger for % x\n", priv->dma_ch); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); +#ifdef SDDMA_RX_FIX +#else + add_timer(&priv->rx_timer); +#endif + priv->tx_dma_buf.head = 0; + priv->tx_dma_buf.tail = 0; + priv->tx_dma_buf.buf = xmit->buf; + + pr_debug("head:0x%x tail:0x%x\n", xmit->head, xmit->tail); + xmit->head = 0; + xmit->tail = 0; + + priv->dma_tx_addr = dma_map_single(port->dev, priv->tx_dma_buf.buf, + UART_XMIT_SIZE, DMA_TO_DEVICE); + + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_tx_sdma_enqueue(priv->dma_ch, priv->dma_tx_addr); + ast_uart_tx_sdma_update(priv->dma_ch, 0); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); + return 0; +} + +static void ast25xx_uart_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + + pr_debug("line[%d]\n", port->line); + priv->up = NULL; + + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + ast_serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + ast25xx_uart_clear_fifos(up); + + (void)ast_serial_in(up, UART_RX); + + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); +#ifdef SDDMA_RX_FIX +#else + del_timer_sync(&up->rx_timer); +#endif + + // Tx buffer will free by serial_core.c + free_irq(up->port.irq, ast_uart_irq); +} + +static unsigned int ast25xx_uart_get_divisor(struct uart_port *port, + unsigned int baud) +{ + unsigned int quot; + + quot = uart_get_divisor(port, baud); + + return quot; +} + +static void ast25xx_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (termios->c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = ast25xx_uart_get_divisor(port, baud); + + if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) { + if (baud < 2400) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; + else + fcr = uart_config[up->port.type].fcr; + } + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + ast_serial_out(up, UART_IER, up->ier); + + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + + serial_dl_write(up, quot); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +/* + * Resource handling. + */ +static int ast25xx_uart_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + int ret = 0; + + if (!up->port.mapbase) + return ret; + + if (!request_mem_region(up->port.mapbase, size, "ast-uart-dma")) { + ret = -EBUSY; + return ret; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap_nocache(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + return ret; + } + } + return ret; +} + +static void ast25xx_uart_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + + if (!up->port.mapbase) + return; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); +} + +static void ast25xx_uart_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + ret = ast25xx_uart_request_std_resource(up); + if (ret == 0) + ast25xx_uart_release_std_resource(up); + + return ret; +} + +static void ast25xx_uart_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = ast25xx_uart_request_std_resource(up); + if (ret < 0) + return; + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + if (up->port.type == PORT_UNKNOWN) + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + return 0; +} + +static const char *ast25xx_uart_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + + + +static unsigned int ast25xx_uart_serial_in(struct uart_port *port, int offset) +{ + offset = offset << port->regshift; + return readb(port->membase + offset); + +} + + +static void ast25xx_uart_serial_out(struct uart_port *port, + int offset, int value) +{ + offset = offset << port->regshift; + writeb(value, port->membase + offset); +} + +static const struct uart_ops ast25xx_uart_pops = { + .tx_empty = ast25xx_uart_tx_empty, + .set_mctrl = ast25xx_uart_set_mctrl, + .get_mctrl = ast25xx_uart_get_mctrl, + .stop_tx = ast25xx_uart_stop_tx, + .start_tx = ast25xx_uart_start_tx, + .stop_rx = ast25xx_uart_stop_rx, + .enable_ms = ast25xx_uart_enable_ms, + .break_ctl = ast25xx_uart_break_ctl, + .startup = ast25xx_uart_startup, + .shutdown = ast25xx_uart_shutdown, + .set_termios = ast25xx_uart_set_termios, + .type = ast25xx_uart_type, + .release_port = ast25xx_uart_release_port, + .request_port = ast25xx_uart_request_port, + .config_port = ast25xx_uart_config_port, + .verify_port = ast25xx_uart_verify_port, +}; + + + +/* + * Register a set of serial devices attached to a platform device. The + * list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +struct clk *clk; + +static int ast25xx_uart_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct ast_uart_priv_data *priv; + struct uart_8250_port port_8250; + struct uart_8250_port *up; + int ret; + u32 read, dma_channel = 0; + struct resource *res; + + if (UART_XMIT_SIZE > DMA_BUFF_SIZE) + pr_debug("UART_XMIT_SIZE > DMA_BUFF_SIZE : Please Check\n"); + + priv = (struct ast_uart_priv_data *)devm_kzalloc(&pdev->dev, + sizeof(struct ast_uart_priv_data), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + up = &port_8250; + memset(up, 0, sizeof(struct uart_8250_port)); + up->port.flags = UPF_IOREMAP; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res == NULL) { + dev_err(&pdev->dev, "IRQ resource not found"); + return -ENODEV; + } + up->port.irq = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Register base not found"); + return -ENODEV; + } + up->port.mapbase = res->start; + + ret = ast25xx_uart_request_std_resource(up); + if (ret) { + dev_err(&pdev->dev, "ioremap_nocache Failed"); + return ret; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + dev_err(&pdev->dev, "missing controller clock"); + + ret = clk_prepare_enable(clk); + if (ret) + dev_err(&pdev->dev, "failed to enable DMA UART Clk"); + + up->port.uartclk = clk_get_rate(clk); + + if (of_property_read_u32(np, "reg-shift", &read) == 0) + up->port.regshift = read; + if (of_property_read_u32(np, "dma-channel", &read) == 0) { + dma_channel = read; + priv->dma_ch = dma_channel; + } + up->port.iotype = UPIO_MEM; + up->port.flags |= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + up->port.dev = &pdev->dev; + if (share_irqs) + up->port.flags |= UPF_SHARE_IRQ; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->port.type = PORT_16550; + up->port.iotype = UPIO_MEM; + up->port.flags = UPF_FIXED_TYPE; + up->port.startup = ast25xx_uart_startup; + up->port.shutdown = ast25xx_uart_shutdown; + up->port.set_termios = ast25xx_uart_set_termios; + up->port.set_mctrl = ast25xx_uart_set_mctrl; + up->port.serial_in = ast25xx_uart_serial_in; + up->port.serial_out = ast25xx_uart_serial_out; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + up->capabilities |= UART_CAP_FIFO; + + up->port.private_data = priv; + + ret = serial8250_register_8250_port(up); + if (ret < 0) { + dev_err(&pdev->dev, + "unable to registr port (IO%lx MEM%llx IRQ%d):%d\n", + up->port.iobase, (unsigned long long)up->port.mapbase, + up->port.irq, ret); + return ret; + } + priv->line = ret; + + tasklet_init(&priv->tx_tasklet, ast_uart_tx_sdma_tasklet_func, + (unsigned long)priv); +#ifdef SDDMA_RX_FIX + tasklet_init(&priv->rx_tasklet, ast_uart_rx_sdma_tasklet_func, + (unsigned long)priv); +#else + uart->rx_timer.data = (unsigned long)port; + uart->rx_timer.expires = jiffies + (HZ); + uart->rx_timer.function = ast_uart_rx_timer_func; + init_timer(&priv->rx_timer); +#endif + +//DMA request +#ifdef SDDMA_RX_FIX + priv->rx_dma_buf.buf = + ast_uart_rx_sdma_request(priv->dma_ch, ast_uart_rx_buffdone, + priv); + if (priv->rx_dma_buf.buf < 0) { + pr_debug("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; +} +#else + priv->rx_dma_buf.buf = ast_uart_rx_sdma_request( + priv->dma_ch, priv); + if (priv->rx_dma_buf.buf < 0) { + pr_debug("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } +#endif + if (ast_uart_tx_sdma_request( + priv->dma_ch, ast_uart_tx_buffdone, priv) < 0) { + pr_debug("Error : failed to get tx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } + + platform_set_drvdata(pdev, priv); + return 0; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ast25xx_uart_remove(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_unregister_port(priv->line); + return 0; +} + +static int ast25xx_uart_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_suspend_port(priv->line); + return 0; +} + +static int ast25xx_uart_resume(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_resume_port(priv->line); + return 0; +} + +static const struct of_device_id ast_serial_dt_ids[] = { + { .compatible = "aspeed,ast-sdma-uart", }, + { /* sentinel */ } +}; + +static struct platform_driver ast25xx_uart_driver = { + .probe = ast25xx_uart_probe, + .remove = ast25xx_uart_remove, + .suspend = ast25xx_uart_suspend, + .resume = ast25xx_uart_resume, + .driver = { + .name = "ast-uart-dma", + .of_match_table = of_match_ptr(ast_serial_dt_ids), + }, +}; + +static int __init ast_uart_init(void) +{ + int ret; + + if (nr_uarts > UART_DMA_NR) + nr_uarts = UART_DMA_NR; + + ret = ast_uart_sdma_probe(); + if (ret) { + pr_debug("ast_uart_sdma_probe Failed ret = %d\n", ret); + goto out; + } + pr_debug("UART driver with DMA%d ports IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); + + spin_lock_init(&ast_uart_irq[0].lock); + + ret = platform_driver_register(&ast25xx_uart_driver); + if (ret == 0) + goto out; + +out: + return ret; +} + +static void __exit ast_uart_exit(void) +{ + + platform_driver_unregister(&ast25xx_uart_driver); + +} +module_init(ast_uart_init); +module_exit(ast_uart_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("AST DMA serial driver"); +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR); -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
* [patch 1/5] AST2500 DMA UART driver @ 2019-06-21 11:17 ` sudheer.v 0 siblings, 0 replies; 26+ messages in thread From: sudheer.v @ 2019-06-21 11:17 UTC (permalink / raw) To: gregkh, jslaby, joel, andrew, benh, robh+dt, mark.rutland, shivahshankar.shankarnarayanrao, shivahshankar, sudheer.veliseti Cc: sudheer veliseti, linux-kernel, linux-serial, devicetree, linux-aspeed From: sudheer veliseti <sudheer.open@gmail.com> UART driver for Aspeed's bmc chip AST2500 Design approch: AST2500 has dedicated Uart DMA controller which has 12 sets of Tx and RX channels connected to UART controller directly. Since the DMA controller have dedicated buffers and registers, there would be little benifit in adding DMA framework overhead. So the software for DMA controller is included within the UART driver itself. implementation details: 'struct uart_8250_port' serial port is populated and registered with 8250_core. Rx and Tx dma channels are requested from DMA controller software Layer, which is part of uart driver itself. Interrupt service routine for DMA controller is the crucial one for Handling all the tx and rx data. ISRs installed for individual uarts are just dummy,and are helpful only to report any spurious interrupts in hardware. Signed-off-by: sudheer veliseti <sudheer.open@gmail.com> --- .../tty/serial/8250/8250_ast2500_uart_dma.c | 1879 +++++++++++++++++ 1 file changed, 1879 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_ast2500_uart_dma.c diff --git a/drivers/tty/serial/8250/8250_ast2500_uart_dma.c b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c new file mode 100644 index 000000000000..13911a0a745a --- /dev/null +++ b/drivers/tty/serial/8250/8250_ast2500_uart_dma.c @@ -0,0 +1,1879 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DMA UART Driver for ASPEED BMC chip: AST2500 + * + * Copyright (C) 2019 sudheer Kumar veliseti, Aspeed technology Inc. + * <open.sudheer@gmail.com> + * + */ +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/mutex.h> +#include <linux/nmi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#include "8250.h" + +#define DMA_BUFF_SIZE 0x1000 // 4096 +#define SDMA_RX_BUFF_SIZE 0x10000 // 65536 + +#define SDDMA_RX_FIX 1 +/* enum ast_uart_chan_op + * operation codes passed to the DMA code by the user, and also used + * to inform the current channel owner of any changes to the system state + */ + +enum ast_uart_chan_op { + AST_UART_DMAOP_TRIGGER, + AST_UART_DMAOP_STOP, + AST_UART_DMAOP_PAUSE, +}; + +/* ast_uart_dma_cbfn_t * * buffer callback routine type */ +typedef void (*ast_uart_dma_cbfn_t)(void *dev_id, u16 len); + +struct ast_sdma_info { + u8 ch_no; + u8 direction; + u8 enable; + void *priv; + char *sdma_virt_addr; + dma_addr_t dma_phy_addr; + /* cdriver callbacks */ + ast_uart_dma_cbfn_t callback_fn; /* buffer done callback */ +}; + +#define AST_UART_SDMA_CH 12 + +struct ast_sdma_ch { + struct ast_sdma_info tx_dma_info[AST_UART_SDMA_CH]; + struct ast_sdma_info rx_dma_info[AST_UART_SDMA_CH]; +}; + +struct ast_sdma { + void __iomem *reg_base; + int dma_irq; + struct ast_sdma_ch *dma_ch; + struct regmap *map; +}; + + + +#define UART_TX_SDMA_EN 0x00 +#define UART_RX_SDMA_EN 0x04 +#define UART_SDMA_CONF 0x08 +#define UART_SDMA_TIMER 0x0C +#define UART_TX_SDMA_REST 0x20 +#define UART_RX_SDMA_REST 0x24 +#define UART_TX_SDMA_IER 0x30 +#define UART_TX_SDMA_ISR 0x34 +#define UART_RX_SDMA_IER 0x38 +#define UART_RX_SDMA_ISR 0x3C +#define UART_TX_R_POINT(x) (0x40 + (x * 0x20)) +#define UART_TX_W_POINT(x) (0x44 + (x * 0x20)) +#define UART_TX_SDMA_ADDR(x) (0x48 + (x * 0x20)) +#define UART_RX_R_POINT(x) (0x50 + (x * 0x20)) +#define UART_RX_W_POINT(x) (0x54 + (x * 0x20)) +#define UART_RX_SDMA_ADDR(x) (0x58 + (x * 0x20)) + +/* UART_TX_SDMA_EN-0x00 : UART TX DMA Enable */ +/* UART_RX_SDMA_EN-0x04 : UART RX DMA Enable */ +#define SDMA_CH_EN(x) (0x1 << (x)) + +/* UART_SDMA_CONF - 0x08 : Misc, Buffer size */ +#define SDMA_TX_BUFF_SIZE_MASK (0x3) +#define SDMA_SET_TX_BUFF_SIZE(x) (x) +#define SDMA_BUFF_SIZE_1KB (0x0) +#define SDMA_BUFF_SIZE_4KB (0x1) +#define SDMA_BUFF_SIZE_16KB (0x2) +#define SDMA_BUFF_SIZE_64KB (0x3) +#define SDMA_RX_BUFF_SIZE_MASK (0x3 << 2) +#define SDMA_SET_RX_BUFF_SIZE(x) (x << 2) +#define SDMA_TIMEOUT_DIS (0x1 << 4) + +/* UART_SDMA_TIMER-0x0C : UART DMA time out timer */ + +/* UART_TX_SDMA_IER 0x30 */ +/* UART_TX_SDMA_ISR 0x34 */ + +#define UART_SDMA11_INT (1 << 11) +#define UART_SDMA10_INT (1 << 10) +#define UART_SDMA9_INT (1 << 9) +#define UART_SDMA8_INT (1 << 8) +#define UART_SDMA7_INT (1 << 7) +#define UART_SDMA6_INT (1 << 6) +#define UART_SDMA5_INT (1 << 5) +#define UART_SDMA4_INT (1 << 4) +#define UART_SDMA3_INT (1 << 3) +#define UART_SDMA2_INT (1 << 2) +#define UART_SDMA1_INT (1 << 1) +#define UART_SDMA0_INT (1 << 0) + + +/* + * Configuration: + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option + * is unsafe when used on edge-triggered interrupts. + */ +static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; + +static unsigned int nr_uarts = CONFIG_AST_RUNTIME_DMA_UARTS; + + +#define PASS_LIMIT 256 + +#include <asm/serial.h> + +#define UART_DMA_NR CONFIG_AST_NR_DMA_UARTS + + +struct ast_uart_priv_data { + + unsigned short line; //index of uart port + struct uart_8250_port *up; + u8 dma_ch; // dma channel number + struct circ_buf rx_dma_buf; + struct circ_buf tx_dma_buf; + dma_addr_t dma_rx_addr; /* Mapped ADMA descr. table */ + dma_addr_t dma_tx_addr; /* Mapped ADMA descr. table */ +#ifdef SDDMA_RX_FIX + struct tasklet_struct rx_tasklet; +#else + struct timer_list rx_timer; +#endif + struct tasklet_struct tx_tasklet; + spinlock_t lock; + int tx_done; + int tx_count; +}; + + +static inline struct uart_8250_port * +to_uart_8250_port(struct uart_port *uart) { + return container_of(uart, struct uart_8250_port, port); +} + +struct irq_info { + spinlock_t lock; + struct uart_8250_port *up; +}; + +static struct irq_info ast_uart_irq[1]; +static DEFINE_MUTEX(ast_uart_mutex); + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 + | UART_FCR_DMA_SELECT, + .flags = UART_CAP_FIFO, + }, +}; + +/* sane hardware needs no mapping */ +#define map_8250_in_reg(up, offset) (offset) +#define map_8250_out_reg(up, offset) (offset) + +// SDMA - software Layer : (previously was in ast-uart-sdma.c) +static inline void ast_uart_sdma_write(struct ast_sdma *sdma, + u32 val, u32 reg) +{ + pr_debug("uart dma write:val:%x,reg:%x\n", val, reg); + writel(val, sdma->reg_base + reg); +} + +static inline u32 ast_uart_sdma_read(struct ast_sdma *sdma, u32 reg) +{ + return readl(sdma->reg_base + reg); +} + +struct ast_sdma ast_uart_sdma; + +int ast_uart_rx_sdma_enqueue(u8 ch, dma_addr_t rx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("ch = %d, rx buff = %x\n", ch, rx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, rx_buff, UART_RX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_tx_sdma_enqueue(u8 ch, dma_addr_t tx_buff) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("ch = %d, tx buff = %x\n", ch, tx_buff); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, tx_buff, UART_TX_SDMA_ADDR(ch)); + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + pr_debug("Trigger\n"); + dma_ch->enable = 1; +#ifdef SDDMA_RX_FIX +#else + ast_uart_set_sdma_time_out(0xffff); +#endif + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) | (0x1 << ch), + UART_RX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + // disable engine + pr_debug("STOP\n"); + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) | + (0x1 << ch), + UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_REST) & + ~(0x1 << ch), + UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(ch)); + ast_uart_sdma_write(sdma, dma_ch->dma_phy_addr, UART_RX_SDMA_ADDR(ch)); + break; + case AST_UART_DMAOP_PAUSE: + // disable engine + dma_ch->enable = 0; + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << ch), + UART_RX_SDMA_EN); + break; + } + + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_ctrl(u8 ch, enum ast_uart_chan_op op) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + pr_debug("TX DMA CTRL [ch %d]\n", ch); + + local_irq_save(flags); + + switch (op) { + case AST_UART_DMAOP_TRIGGER: + pr_debug("TRIGGER : Enable\n"); + dma_ch->enable = 1; + // set enable + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) | (0x1 << ch), + UART_TX_SDMA_EN); + break; + case AST_UART_DMAOP_STOP: + pr_debug("STOP : DISABLE & RESET\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + // set reset + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) | + (0x1 << ch), + UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_REST) & + ~(0x1 << ch), + UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(ch)); + break; + case AST_UART_DMAOP_PAUSE: + pr_debug("PAUSE : DISABLE\n"); + dma_ch->enable = 0; + // disable engine + ast_uart_sdma_write(sdma, ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) & + ~(0x1 << ch), + UART_TX_SDMA_EN); + } + + local_irq_restore(flags); + return 0; +} + +u32 ast_uart_get_tx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_TX_R_POINT(ch)); +} + +int ast_uart_tx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("TX DMA CTRL [ch %d] point %d\n", ch, point); + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_TX_W_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +int ast_uart_tx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->tx_dma_info[ch]); + + pr_debug("TX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_IER) | (1 << ch), + UART_TX_SDMA_IER); + + local_irq_restore(flags); + + return 0; +} + +int ast_uart_rx_sdma_update(u8 ch, u16 point) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + + pr_debug("RX DMA CTRL [ch %d] point %x\n", ch, point); + + local_irq_save(flags); + ast_uart_sdma_write(sdma, point, UART_RX_R_POINT(ch)); + local_irq_restore(flags); + return 0; +} + +#ifdef SDDMA_RX_FIX +char *ast_uart_rx_sdma_request(u8 ch, ast_uart_dma_cbfn_t rtn, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return 0; + } + dma_ch->priv = id; + + dma_ch->callback_fn = rtn; + + // DMA IRQ En + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_IER) | (1 << ch), + UART_RX_SDMA_IER); + + local_irq_restore(flags); + + return dma_ch->sdma_virt_addr; +} + +#else +char *ast_uart_rx_sdma_request(u8 ch, void *id) +{ + unsigned long flags; + struct ast_sdma *sdma = &ast_uart_sdma; + struct ast_sdma_info *dma_ch = &(sdma->dma_ch->rx_dma_info[ch]); + + pr_debug("RX DMA REQUEST ch = %d\n", ch); + + local_irq_save(flags); + + if (dma_ch->enable) { + local_irq_restore(flags); + return -EBUSY; + } + dma_ch->priv = id; + + local_irq_restore(flags); + return dma_ch->sdma_virt_addr; +} +#endif + +u16 ast_uart_get_rx_sdma_pt(u8 ch) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + return ast_uart_sdma_read(sdma, UART_RX_W_POINT(ch)); +} + +void ast_uart_set_sdma_time_out(u16 val) +{ + struct ast_sdma *sdma = &ast_uart_sdma; + + ast_uart_sdma_write(sdma, val, UART_SDMA_TIMER); +} + +static inline void ast_sdma_bufffdone(struct ast_sdma_info *sdma_ch) +{ + u32 len; + struct ast_sdma *sdma = &ast_uart_sdma; + + if (sdma_ch->enable == 0) { + pr_debug("sdma Please check ch_no %x %s!!!!!\n", + sdma_ch->ch_no, sdma_ch->direction ? "TX" : "RX"); + if (sdma_ch->direction) { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_TX_SDMA_EN) + & ~(0x1 << sdma_ch->ch_no), UART_TX_SDMA_EN); + } else { + ast_uart_sdma_write(sdma, + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN) & + ~(0x1 << sdma_ch->ch_no), UART_RX_SDMA_EN); + ast_uart_rx_sdma_update(sdma_ch->ch_no, + ast_uart_get_rx_sdma_pt(sdma_ch->ch_no)); + pr_debug("OFFSET : UART_RX_SDMA_EN = %x\n ", + ast_uart_sdma_read(sdma, UART_RX_SDMA_EN)); + } + return; + } + + if (sdma_ch->direction) { + len = ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)); + pr_debug("tx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_TX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_TX_W_POINT(sdma_ch->ch_no)) + ); + } else { + pr_debug("rx rp %x , wp %x\n", + ast_uart_sdma_read(sdma, UART_RX_R_POINT(sdma_ch->ch_no)), + ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)) + ); + len = ast_uart_sdma_read(sdma, UART_RX_W_POINT(sdma_ch->ch_no)); + } + + pr_debug("<dma dwn>: ch[%d] : %s ,len : %d\n", sdma_ch->ch_no, + sdma_ch->direction ? "tx" : "rx", len); + + if (sdma_ch->callback_fn != NULL) + (sdma_ch->callback_fn)(sdma_ch->priv, len); +} + +static irqreturn_t ast_uart_sdma_isr(int irq, void *dev_id) +{ + struct ast_sdma *sdma = (struct ast_sdma *)dev_id; + + u32 tx_sts = ast_uart_sdma_read(sdma, UART_TX_SDMA_ISR); + u32 rx_sts = ast_uart_sdma_read(sdma, UART_RX_SDMA_ISR); + + pr_debug("tx sts : %x, rx sts : %x\n", tx_sts, rx_sts); + + if ((tx_sts == 0) && (rx_sts == 0)) { + pr_debug("SDMA IRQ ERROR !!!\n"); + return IRQ_HANDLED; + } + + if (rx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[0])); + } else if (rx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[1])); + } else if (rx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[2])); + } else if (rx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[3])); + } else if (rx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[4])); + } else if (rx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[5])); + } else if (rx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[6])); + } else if (rx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[7])); + } else if (rx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[8])); + } else if (rx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[9])); + } else if (rx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[10])); + } else if (rx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_RX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->rx_dma_info[11])); + } else { + + } + + if (tx_sts & UART_SDMA0_INT) { + ast_uart_sdma_write(sdma, UART_SDMA0_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[0])); + } else if (tx_sts & UART_SDMA1_INT) { + ast_uart_sdma_write(sdma, UART_SDMA1_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[1])); + } else if (tx_sts & UART_SDMA2_INT) { + ast_uart_sdma_write(sdma, UART_SDMA2_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[2])); + } else if (tx_sts & UART_SDMA3_INT) { + ast_uart_sdma_write(sdma, UART_SDMA3_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[3])); + } else if (tx_sts & UART_SDMA4_INT) { + ast_uart_sdma_write(sdma, UART_SDMA4_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[4])); + } else if (tx_sts & UART_SDMA5_INT) { + ast_uart_sdma_write(sdma, UART_SDMA5_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[5])); + } else if (tx_sts & UART_SDMA6_INT) { + ast_uart_sdma_write(sdma, UART_SDMA6_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[6])); + } else if (tx_sts & UART_SDMA7_INT) { + ast_uart_sdma_write(sdma, UART_SDMA7_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[7])); + } else if (tx_sts & UART_SDMA8_INT) { + ast_uart_sdma_write(sdma, UART_SDMA8_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[8])); + } else if (tx_sts & UART_SDMA9_INT) { + ast_uart_sdma_write(sdma, UART_SDMA9_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[9])); + } else if (tx_sts & UART_SDMA10_INT) { + ast_uart_sdma_write(sdma, UART_SDMA10_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[10])); + } else if (tx_sts & UART_SDMA11_INT) { + ast_uart_sdma_write(sdma, UART_SDMA11_INT, UART_TX_SDMA_ISR); + ast_sdma_bufffdone(&(sdma->dma_ch->tx_dma_info[11])); + } else { + } + + return IRQ_HANDLED; +} + +static int ast_uart_sdma_probe(void) +{ + int i; + struct device_node *node; + int ret; + struct ast_sdma *sdma = &ast_uart_sdma; + char *rx_dma_virt_addr; + dma_addr_t rx_dma_phy_addr; + + sdma->dma_ch = kzalloc(sizeof(struct ast_sdma_ch), GFP_KERNEL); + if (!sdma->dma_ch) + return -ENOMEM; + + // sdma memory mapping + node = of_find_compatible_node(NULL, NULL, "aspeed,ast-uart-sdma"); + if (!node) + return -ENODEV; + + sdma->reg_base = of_iomap(node, 0); + if (IS_ERR(sdma->reg_base)) + return PTR_ERR(sdma->map); + rx_dma_virt_addr = dma_alloc_coherent(NULL, + SDMA_RX_BUFF_SIZE * AST_UART_SDMA_CH, &rx_dma_phy_addr, GFP_KERNEL); + + if (!rx_dma_virt_addr) { + pr_debug("rx_dma_virt_addr Err:dma alloc Failed\n"); + return -ENOMEM; + } + for (i = 0; i < AST_UART_SDMA_CH; i++) { + // TX ------------------------ + sdma->dma_ch->tx_dma_info[i].enable = 0; + sdma->dma_ch->tx_dma_info[i].ch_no = i; + sdma->dma_ch->tx_dma_info[i].direction = 1; + ast_uart_sdma_write(sdma, 0, UART_TX_W_POINT(i)); + // RX ------------------------ + sdma->dma_ch->rx_dma_info[i].enable = 0; + sdma->dma_ch->rx_dma_info[i].ch_no = i; + sdma->dma_ch->rx_dma_info[i].direction = 0; + sdma->dma_ch->rx_dma_info[i].sdma_virt_addr = + rx_dma_virt_addr + (SDMA_RX_BUFF_SIZE * i); + sdma->dma_ch->rx_dma_info[i].dma_phy_addr = + rx_dma_phy_addr + (SDMA_RX_BUFF_SIZE * i); + ast_uart_sdma_write(sdma, + sdma->dma_ch->rx_dma_info[i].dma_phy_addr, + UART_RX_SDMA_ADDR(i)); + ast_uart_sdma_write(sdma, 0, UART_RX_R_POINT(i)); + } + + ast_uart_sdma_write(sdma, 0xffffffff, UART_TX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_TX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0xffffffff, UART_RX_SDMA_REST); + ast_uart_sdma_write(sdma, 0x0, UART_RX_SDMA_REST); + + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_EN); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_EN); + +#ifdef SDDMA_RX_FIX + ast_uart_sdma_write(sdma, 0x200, UART_SDMA_TIMER); +#else + ast_uart_sdma_write(sdma, 0xffff, UART_SDMA_TIMER); +#endif + + // TX + ast_uart_sdma_write(sdma, 0xfff, UART_TX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_TX_SDMA_IER); + + // RX + ast_uart_sdma_write(sdma, 0xfff, UART_RX_SDMA_ISR); + ast_uart_sdma_write(sdma, 0, UART_RX_SDMA_IER); + + sdma->dma_irq = of_irq_get(node, 0); + ret = request_irq(sdma->dma_irq, ast_uart_sdma_isr, 0, + "sdma-intr", sdma); + if (ret) { + pr_debug("Unable to get UART SDMA IRQ %x\n", ret); + return -ENODEV; + } + + ast_uart_sdma_write(sdma, SDMA_SET_TX_BUFF_SIZE(SDMA_BUFF_SIZE_4KB) | + SDMA_SET_RX_BUFF_SIZE(SDMA_BUFF_SIZE_64KB), + UART_SDMA_CONF); + return 0; +} + +// END of SDMA Layer + +// UART Driver Layer + +static unsigned int ast_serial_in(struct uart_8250_port *up, int offset) +{ + offset = map_8250_in_reg(up, offset) << up->port.regshift; + return readb(up->port.membase + offset); +} + +static void ast_serial_out(struct uart_8250_port *up, int offset, int value) +{ + /* Save the offset before it's remapped */ + offset = map_8250_out_reg(up, offset) << up->port.regshift; + writeb(value, up->port.membase + offset); +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) ast_serial_in(up, offset) +#define serial_outp(up, offset, value) ast_serial_out(up, offset, value) + +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) + +static void ast_uart_tx_sdma_tasklet_func(unsigned long data) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit = NULL; + u32 tx_pt; + + + if (!up) + return; + xmit = &up->port.state->xmit; + spin_lock(&up->port.lock); + priv->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); + dma_sync_single_for_device(up->port.dev, priv->dma_tx_addr, + UART_XMIT_SIZE, DMA_TO_DEVICE); + tx_pt = ast_uart_get_tx_sdma_pt(priv->dma_ch); + + if (tx_pt > xmit->head) { + if ((tx_pt & 0xfffc) == 0) + ast_uart_tx_sdma_update(priv->dma_ch, 0xffff); + else + ast_uart_tx_sdma_update(priv->dma_ch, 0); + } else { + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + } + ast_uart_tx_sdma_update(priv->dma_ch, xmit->head); + spin_unlock(&up->port.lock); +} + +static void ast_uart_tx_buffdone(void *dev_id, u16 len) +{ + + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct uart_8250_port *up = priv->up; + struct circ_buf *xmit; + + if (!up) + return; + xmit = &(up->port.state->xmit); + + pr_debug("line[%d] : tx len = % d\n", priv->line, len); + spin_lock(&up->port.lock); + xmit->tail = len; + pr_debug(" line[%d], xmit->head = %d, xmit->tail = % d\n", + priv->line, xmit->head, xmit->tail); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (xmit->head != xmit->tail) + tasklet_schedule(&priv->tx_tasklet); + + spin_unlock(&up->port.lock); +} + +#ifdef SDDMA_RX_FIX +static void ast_uart_rx_sdma_tasklet_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct tty_port *ttyport; + int count; + int copy = 0; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + + ttyport = &up->port.state->port; + + pr_debug("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + spin_lock(&up->port.lock); + if (rx_ring->head > rx_ring->tail) { + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + } + + if (copy != count) + pr_debug(" !!!!!!!!ERROR 111\n"); + if (count) { + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + up->port.icount.rx += count; + tty_flip_buffer_push(ttyport); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + } + spin_unlock(&up->port.lock); +} + +static void ast_uart_rx_buffdone(void *dev_id, u16 len) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)dev_id; + struct circ_buf *rx_ring = &priv->rx_dma_buf; + struct uart_8250_port *up = priv->up; + + if (!up) + return; + pr_debug("line[%d], head = %d,len:%d\n", + priv->line, priv->rx_dma_buf.head, len); + spin_lock(&up->port.lock); + rx_ring->head = len; + spin_unlock(&up->port.lock); + tasklet_schedule(&priv->rx_tasklet); +} + +#else +static void ast_uart_rx_timer_func(unsigned long data) +{ + struct ast_uart_priv_data *priv = (struct ast_uart_priv_data *)data; + struct uart_8250_port *up = priv->up; + struct tty_port *ttyport; + struct circ_buf *rx_ring; + struct tty_struct *tty; + char flag; + int count; + int copy; + + + if (!up) + return; + ttyport = &up->port.state->port; + rx_ring = &up->rx_dma_buf; + tty = up->port.state->port.tty; + + pr_debug("line[%d], rx_ring->head = % d, rx_ring->tail = % d\n", + up->port.line, rx_ring->head, rx_ring->tail); + rx_ring->head = ast_uart_get_rx_sdma_pt(priv->dma_ch); + del_timer(&up->rx_timer); + + if (rx_ring->head > rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = rx_ring->head - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else if (rx_ring->head < rx_ring->tail) { + ast_uart_set_sdma_time_out(0xffff); + count = SDMA_RX_BUFF_SIZE - rx_ring->tail; + copy = tty_insert_flip_string(ttyport, + rx_ring->buf + rx_ring->tail, count); + } else { + count = 0; + // pr_debug("@@--%s-- ch = 0x%x\n", __func__, ch); + } + + if (copy != count) + pr_debug(" !!!!!!!!ERROR 111\n"); + rx_ring->tail += count; + rx_ring->tail &= (SDMA_RX_BUFF_SIZE - 1); + + if (count) { + //pr_debug("\n count = % d\n", count); + up->port.icount.rx += count; + spin_lock(&up->port.lock); + tty_flip_buffer_push(ttyport); + spin_unlock(&up->port.lock); + //pr_debug("update rx_ring->tail % x\n", rx_ring->tail); + ast_uart_rx_sdma_update(priv->dma_ch, rx_ring->tail); + priv->workaround = 1; + } else { + if (priv->workaround) { + priv->workaround++; + if (priv->workaround > 1) + ast_uart_set_sdma_time_out(0); + else + ast_uart_set_sdma_time_out(0xffff); + } + } + add_timer(&up->rx_timer); +} +#endif + +/* + * FIFO support. + */ +static inline void ast25xx_uart_clear_fifos(struct uart_8250_port *p) +{ + serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(p, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(p, UART_FCR, 0); +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned long flags; + + pr_debug("line[%d]\n", up->port.line); + if (!up->port.iobase && !up->port.mapbase && !up->port.membase) + return; + + pr_debug("ttyDMA%d : autoconf (0x%04lx, 0x%p) : ", up->port.line, + up->port.iobase, up->port.membase); + + spin_lock_irqsave(&up->port.lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + + if (up->port.type == PORT_UNKNOWN) + goto out; + + /* + * Reset the UART. + */ + ast25xx_uart_clear_fifos(up); + ast_serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); + pr_debug("type=%s\n", uart_config[up->port.type].name); +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + ast_serial_out(p, UART_IER, p->ier); + } +} + +static void ast25xx_uart_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", up->port.line); + __stop_tx(up); +} + +static void transmit_chars(struct uart_8250_port *up); + +static void ast25xx_uart_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + + pr_debug("line[%d]\n", port->line); + tasklet_schedule(&priv->tx_tasklet); +} + +static void ast25xx_uart_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", port->line); + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + ast_serial_out(up, UART_IER, up->ier); +} + +static void ast25xx_uart_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + pr_debug("line[%d]\n", port->line); + up->ier |= UART_IER_MSI; + ast_serial_out(up, UART_IER, up->ier); +} + +static void transmit_chars(struct uart_8250_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + ast25xx_uart_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + ast_serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static unsigned int check_modem_status(struct uart_8250_port *up) +{ + unsigned int status = ast_serial_in(up, UART_MSR); + + pr_debug("line[%d]\n", up->port.line); + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI + && up->port.state != NULL) { + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, + status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, + status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); + } + + return status; +} + +/* + * This handles the interrupt from one port. + */ +static inline void ast25xx_uart_handle_port(struct uart_8250_port *up) +{ + unsigned int status; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + status = serial_inp(up, UART_LSR); + + pr_debug("status = %x\n", status); + + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * This is the serial driver's interrupt routine. + */ +static irqreturn_t ast_uart_interrupt(int irq, void *dev_id) +{ + struct irq_info *i = dev_id; + int pass_counter = 0, handled = 0, end = 0; + + pr_debug("(%d)-", irq); + spin_lock(&i->lock); + + do { + struct uart_8250_port *up; + unsigned int iir; + + up = (struct uart_8250_port *)(i->up); + + iir = ast_serial_in(up, UART_IIR); + if (!(iir & UART_IIR_NO_INT)) { + ast25xx_uart_handle_port(up); + handled = 1; + + } else + end = 1; + + if (pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + pr_err("ast-uart-dma:too much work for irq%d\n", irq); + break; + } + } while (end); + + spin_unlock(&i->lock); + + pr_debug("-(%d)\n", irq); + + return IRQ_RETVAL(handled); +} + +static unsigned int ast25xx_uart_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + unsigned int lsr; + + pr_debug("line[%d]\n", up->port.line); + + spin_lock_irqsave(&up->port.lock, flags); + lsr = ast_serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&up->port.lock, flags); + + return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0; +} + +static unsigned int ast25xx_uart_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned int status; + unsigned int ret; + + status = check_modem_status(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void ast25xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char mcr = 0; + + mctrl = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + ast_serial_out(up, UART_MCR, mcr); + +} + +static void ast25xx_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + ast_serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ast25xx_uart_startup(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + // TX DMA + struct circ_buf *xmit = &up->port.state->xmit; + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + unsigned char lsr, iir; + int retval; + int irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; + + priv->up = up; + pr_debug("line[%d]\n", port->line); + up->capabilities = uart_config[up->port.type].flags; + up->mcr = 0; + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + ast25xx_uart_clear_fifos(up); + /* + * Clear the interrupt registers. + */ + (void)serial_inp(up, UART_LSR); + (void)serial_inp(up, UART_RX); + (void)serial_inp(up, UART_IIR); + (void)serial_inp(up, UART_MSR); + + ast_uart_irq[0].up = up; + retval = request_irq(up->port.irq, ast_uart_interrupt, irq_flags, + "ast-uart-dma", ast_uart_irq); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl |= TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_outp(up, UART_IER, UART_IER_THRI); + lsr = ast_serial_in(up, UART_LSR); + iir = ast_serial_in(up, UART_IIR); + serial_outp(up, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + pr_debug("ttyDMA%d-enabling bad tx status\n", + port->line); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_inp(up, UART_LSR); + serial_inp(up, UART_RX); + serial_inp(up, UART_IIR); + serial_inp(up, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + // RX DMA + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; + up->port.icount.rx = 0; + + priv->tx_done = 1; + priv->tx_count = 0; + + priv->rx_dma_buf.head = 0; + priv->rx_dma_buf.tail = 0; +#ifdef SDDMA_RX_FIX +#else + priv->workaround = 0; +#endif + // pr_debug("Sending trigger for % x\n", priv->dma_ch); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); +#ifdef SDDMA_RX_FIX +#else + add_timer(&priv->rx_timer); +#endif + priv->tx_dma_buf.head = 0; + priv->tx_dma_buf.tail = 0; + priv->tx_dma_buf.buf = xmit->buf; + + pr_debug("head:0x%x tail:0x%x\n", xmit->head, xmit->tail); + xmit->head = 0; + xmit->tail = 0; + + priv->dma_tx_addr = dma_map_single(port->dev, priv->tx_dma_buf.buf, + UART_XMIT_SIZE, DMA_TO_DEVICE); + + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_STOP); + ast_uart_tx_sdma_enqueue(priv->dma_ch, priv->dma_tx_addr); + ast_uart_tx_sdma_update(priv->dma_ch, 0); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_TRIGGER); + return 0; +} + +static void ast25xx_uart_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + struct ast_uart_priv_data *priv = up->port.private_data; + unsigned long flags; + + pr_debug("line[%d]\n", port->line); + priv->up = NULL; + + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + ast_serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + ast25xx_uart_clear_fifos(up); + + (void)ast_serial_in(up, UART_RX); + + ast_uart_rx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); + ast_uart_tx_sdma_ctrl(priv->dma_ch, AST_UART_DMAOP_PAUSE); +#ifdef SDDMA_RX_FIX +#else + del_timer_sync(&up->rx_timer); +#endif + + // Tx buffer will free by serial_core.c + free_irq(up->port.irq, ast_uart_irq); +} + +static unsigned int ast25xx_uart_get_divisor(struct uart_port *port, + unsigned int baud) +{ + unsigned int quot; + + quot = uart_get_divisor(port, baud); + + return quot; +} + +static void ast25xx_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (termios->c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = ast25xx_uart_get_divisor(port, baud); + + if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) { + if (baud < 2400) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; + else + fcr = uart_config[up->port.type].fcr; + } + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + ast_serial_out(up, UART_IER, up->ier); + + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + + serial_dl_write(up, quot); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + ast25xx_uart_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +/* + * Resource handling. + */ +static int ast25xx_uart_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + int ret = 0; + + if (!up->port.mapbase) + return ret; + + if (!request_mem_region(up->port.mapbase, size, "ast-uart-dma")) { + ret = -EBUSY; + return ret; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap_nocache(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + return ret; + } + } + return ret; +} + +static void ast25xx_uart_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = 8 << up->port.regshift; + + if (!up->port.mapbase) + return; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); +} + +static void ast25xx_uart_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + ret = ast25xx_uart_request_std_resource(up); + if (ret == 0) + ast25xx_uart_release_std_resource(up); + + return ret; +} + +static void ast25xx_uart_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = to_uart_8250_port(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = ast25xx_uart_request_std_resource(up); + if (ret < 0) + return; + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + if (up->port.type == PORT_UNKNOWN) + ast25xx_uart_release_std_resource(up); +} + +static int ast25xx_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + return 0; +} + +static const char *ast25xx_uart_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + + + +static unsigned int ast25xx_uart_serial_in(struct uart_port *port, int offset) +{ + offset = offset << port->regshift; + return readb(port->membase + offset); + +} + + +static void ast25xx_uart_serial_out(struct uart_port *port, + int offset, int value) +{ + offset = offset << port->regshift; + writeb(value, port->membase + offset); +} + +static const struct uart_ops ast25xx_uart_pops = { + .tx_empty = ast25xx_uart_tx_empty, + .set_mctrl = ast25xx_uart_set_mctrl, + .get_mctrl = ast25xx_uart_get_mctrl, + .stop_tx = ast25xx_uart_stop_tx, + .start_tx = ast25xx_uart_start_tx, + .stop_rx = ast25xx_uart_stop_rx, + .enable_ms = ast25xx_uart_enable_ms, + .break_ctl = ast25xx_uart_break_ctl, + .startup = ast25xx_uart_startup, + .shutdown = ast25xx_uart_shutdown, + .set_termios = ast25xx_uart_set_termios, + .type = ast25xx_uart_type, + .release_port = ast25xx_uart_release_port, + .request_port = ast25xx_uart_request_port, + .config_port = ast25xx_uart_config_port, + .verify_port = ast25xx_uart_verify_port, +}; + + + +/* + * Register a set of serial devices attached to a platform device. The + * list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +struct clk *clk; + +static int ast25xx_uart_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct ast_uart_priv_data *priv; + struct uart_8250_port port_8250; + struct uart_8250_port *up; + int ret; + u32 read, dma_channel = 0; + struct resource *res; + + if (UART_XMIT_SIZE > DMA_BUFF_SIZE) + pr_debug("UART_XMIT_SIZE > DMA_BUFF_SIZE : Please Check\n"); + + priv = (struct ast_uart_priv_data *)devm_kzalloc(&pdev->dev, + sizeof(struct ast_uart_priv_data), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + up = &port_8250; + memset(up, 0, sizeof(struct uart_8250_port)); + up->port.flags = UPF_IOREMAP; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res == NULL) { + dev_err(&pdev->dev, "IRQ resource not found"); + return -ENODEV; + } + up->port.irq = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Register base not found"); + return -ENODEV; + } + up->port.mapbase = res->start; + + ret = ast25xx_uart_request_std_resource(up); + if (ret) { + dev_err(&pdev->dev, "ioremap_nocache Failed"); + return ret; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + dev_err(&pdev->dev, "missing controller clock"); + + ret = clk_prepare_enable(clk); + if (ret) + dev_err(&pdev->dev, "failed to enable DMA UART Clk"); + + up->port.uartclk = clk_get_rate(clk); + + if (of_property_read_u32(np, "reg-shift", &read) == 0) + up->port.regshift = read; + if (of_property_read_u32(np, "dma-channel", &read) == 0) { + dma_channel = read; + priv->dma_ch = dma_channel; + } + up->port.iotype = UPIO_MEM; + up->port.flags |= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + up->port.dev = &pdev->dev; + if (share_irqs) + up->port.flags |= UPF_SHARE_IRQ; + up->port.fifosize = uart_config[up->port.type].fifo_size; + up->port.type = PORT_16550; + up->port.iotype = UPIO_MEM; + up->port.flags = UPF_FIXED_TYPE; + up->port.startup = ast25xx_uart_startup; + up->port.shutdown = ast25xx_uart_shutdown; + up->port.set_termios = ast25xx_uart_set_termios; + up->port.set_mctrl = ast25xx_uart_set_mctrl; + up->port.serial_in = ast25xx_uart_serial_in; + up->port.serial_out = ast25xx_uart_serial_out; + up->capabilities = uart_config[up->port.type].flags; + up->tx_loadsz = uart_config[up->port.type].tx_loadsz; + up->capabilities |= UART_CAP_FIFO; + + up->port.private_data = priv; + + ret = serial8250_register_8250_port(up); + if (ret < 0) { + dev_err(&pdev->dev, + "unable to registr port (IO%lx MEM%llx IRQ%d):%d\n", + up->port.iobase, (unsigned long long)up->port.mapbase, + up->port.irq, ret); + return ret; + } + priv->line = ret; + + tasklet_init(&priv->tx_tasklet, ast_uart_tx_sdma_tasklet_func, + (unsigned long)priv); +#ifdef SDDMA_RX_FIX + tasklet_init(&priv->rx_tasklet, ast_uart_rx_sdma_tasklet_func, + (unsigned long)priv); +#else + uart->rx_timer.data = (unsigned long)port; + uart->rx_timer.expires = jiffies + (HZ); + uart->rx_timer.function = ast_uart_rx_timer_func; + init_timer(&priv->rx_timer); +#endif + +//DMA request +#ifdef SDDMA_RX_FIX + priv->rx_dma_buf.buf = + ast_uart_rx_sdma_request(priv->dma_ch, ast_uart_rx_buffdone, + priv); + if (priv->rx_dma_buf.buf < 0) { + pr_debug("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; +} +#else + priv->rx_dma_buf.buf = ast_uart_rx_sdma_request( + priv->dma_ch, priv); + if (priv->rx_dma_buf.buf < 0) { + pr_debug("Error : failed to get rx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } +#endif + if (ast_uart_tx_sdma_request( + priv->dma_ch, ast_uart_tx_buffdone, priv) < 0) { + pr_debug("Error : failed to get tx dma channel[%d]\n", + priv->dma_ch); + return -EBUSY; + } + + platform_set_drvdata(pdev, priv); + return 0; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ast25xx_uart_remove(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_unregister_port(priv->line); + return 0; +} + +static int ast25xx_uart_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_suspend_port(priv->line); + return 0; +} + +static int ast25xx_uart_resume(struct platform_device *pdev) +{ + struct ast_uart_priv_data *priv; + + priv = platform_get_drvdata(pdev); + serial8250_resume_port(priv->line); + return 0; +} + +static const struct of_device_id ast_serial_dt_ids[] = { + { .compatible = "aspeed,ast-sdma-uart", }, + { /* sentinel */ } +}; + +static struct platform_driver ast25xx_uart_driver = { + .probe = ast25xx_uart_probe, + .remove = ast25xx_uart_remove, + .suspend = ast25xx_uart_suspend, + .resume = ast25xx_uart_resume, + .driver = { + .name = "ast-uart-dma", + .of_match_table = of_match_ptr(ast_serial_dt_ids), + }, +}; + +static int __init ast_uart_init(void) +{ + int ret; + + if (nr_uarts > UART_DMA_NR) + nr_uarts = UART_DMA_NR; + + ret = ast_uart_sdma_probe(); + if (ret) { + pr_debug("ast_uart_sdma_probe Failed ret = %d\n", ret); + goto out; + } + pr_debug("UART driver with DMA%d ports IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); + + spin_lock_init(&ast_uart_irq[0].lock); + + ret = platform_driver_register(&ast25xx_uart_driver); + if (ret == 0) + goto out; + +out: + return ret; +} + +static void __exit ast_uart_exit(void) +{ + + platform_driver_unregister(&ast25xx_uart_driver); + +} +module_init(ast_uart_init); +module_exit(ast_uart_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("AST DMA serial driver"); +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR); -- 2.17.1 ^ permalink raw reply related [flat|nested] 26+ messages in thread
end of thread, other threads:[~2019-06-21 11:17 UTC | newest] Thread overview: 26+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-06-05 12:23 [patch 0/5] *** Cover Letter: patch submission for AST2500 UART driver *** sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` [patch 1/5] AST2500 DMA UART driver sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-10 16:49 ` Greg KH 2019-06-10 16:49 ` Greg KH 2019-06-10 16:49 ` Greg KH 2019-06-10 16:50 ` Greg KH 2019-06-10 16:50 ` Greg KH 2019-06-10 16:50 ` Greg KH 2019-06-05 12:23 ` [patch 2/5] build configuration for " sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` [patch 3/5] DT nodes " sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` [patch 4/5] defconfig and MAINTAINERS updated " sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` [patch 5/5] Documentation: DT bindings " sudheer.v 2019-06-05 12:23 ` sudheer.v 2019-06-05 12:23 ` sudheer.v -- strict thread matches above, loose matches on Subject: below -- 2019-06-21 11:17 [patch 0/5] *** DMA based UART driver for AST2500 *** sudheer.v 2019-06-21 11:17 ` [patch 1/5] AST2500 DMA UART driver sudheer.v 2019-06-21 11:17 ` sudheer.v
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.