Re: [PATCH v2 1/2] dt-binding: spi: add NPCM FIU controller

[Rob Herring <robh@kernel.org>]

On Thu, Aug 08, 2019 at 04:14:47PM +0300, Tomer Maimon wrote:
> Added device tree binding documentation for Nuvoton BMC
> NPCM Flash Interface Unit(FIU) SPI master controller
> using SPI-MEM interface.
> 
> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
> ---
>  .../bindings/spi/nuvoton,npcm-fiu.txt         | 47 +++++++++++++++++++
>  1 file changed, 47 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt
> 
> diff --git a/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt b/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt
> new file mode 100644
> index 000000000000..ab37aae91d19
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt
> @@ -0,0 +1,47 @@
> +* Nuvoton FLASH Interface Unit (FIU) SPI Controller
> +
> +NPCM FIU supports single, dual and quad communication interface.
> +
> +The NPCM7XX supports three FIU modules,
> +FIU0 and FIUx supports two chip selects,
> +FIU3 support four chip select.
> +
> +Required properties:
> +  - compatible : "nuvoton,npcm750-fiu" for the NPCM7XX BMC
> +  - #address-cells : should be 1.
> +  - #size-cells : should be 0.
> +  - reg : the first contains the register location and length,
> +          the second contains the memory mapping address and length
> +  - reg-names: Should contain the reg names "control" and "memory"
> +  - clocks : phandle of FIU reference clock.
> +
> +Required properties in case the pins can be muxed:
> +  - pinctrl-names : a pinctrl state named "default" must be defined.
> +  - pinctrl-0 : phandle referencing pin configuration of the device.
> +
> +Optional property:
> +  - spix-mode: enable spix-mode for an expansion bus to an ASIC or CPLD.

Is this something standard? If not, add a vendor prefix.

> +
> +Aliases:
> +- All the FIU controller nodes should be represented in the aliases node using
> +  the following format 'fiu{n}' where n is a unique number for the alias.
> +  In the NPCM7XX BMC:
> +  		fiu0 represent fiu 0 controller
> +  		fiu1 represent fiu 3 controller
> +  		fiu2 represent fiu x controller
> +
> +Example:
> +fiu3: fiu@c00000000 {

spi@...

> +	compatible = "nuvoton,npcm750-fiu";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	reg = <0xfb000000 0x1000>, <0x80000000 0x10000000>;
> +	reg-names = "control", "memory";
> +	clocks = <&clk NPCM7XX_CLK_AHB>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi3_pins>;
> +	spi-nor@0 {
> +			...
> +	};
> +};
> +
> -- 
> 2.18.0
>