[PATCH 5.3 062/148] drm/i915/dp: Fix dsc bpp calculations, v5.

[Greg Kroah-Hartman <gregkh@linuxfoundation.org>]

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

commit cffb4c3ea37248c4fc2f4ce747e5c24af88aec76 upstream.

There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.

As a result our calculated bpp was way too high, and the link width
limitation never came into effect.

Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.

We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.

This fixes the FIFO underrun we are seeing with FEC enabled.

Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f6cf4 ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit ed06efb801bd291e935238d3fba46fa03d098f0e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/i915/display/intel_display.c |   12 +
 drivers/gpu/drm/i915/display/intel_display.h |    2 
 drivers/gpu/drm/i915/display/intel_dp.c      |  184 +++++++++++++--------------
 drivers/gpu/drm/i915/display/intel_dp.h      |    6 
 drivers/gpu/drm/i915/display/intel_dp_mst.c  |    2 
 5 files changed, 107 insertions(+), 99 deletions(-)

--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -7132,7 +7132,7 @@ retry:
 	pipe_config->fdi_lanes = lane;
 
 	intel_link_compute_m_n(pipe_config->pipe_bpp, lane, fdi_dotclock,
-			       link_bw, &pipe_config->fdi_m_n, false);
+			       link_bw, &pipe_config->fdi_m_n, false, false);
 
 	ret = ironlake_check_fdi_lanes(dev, intel_crtc->pipe, pipe_config);
 	if (ret == -EDEADLK)
@@ -7379,11 +7379,15 @@ void
 intel_link_compute_m_n(u16 bits_per_pixel, int nlanes,
 		       int pixel_clock, int link_clock,
 		       struct intel_link_m_n *m_n,
-		       bool constant_n)
+		       bool constant_n, bool fec_enable)
 {
-	m_n->tu = 64;
+	u32 data_clock = bits_per_pixel * pixel_clock;
+
+	if (fec_enable)
+		data_clock = intel_dp_mode_to_fec_clock(data_clock);
 
-	compute_m_n(bits_per_pixel * pixel_clock,
+	m_n->tu = 64;
+	compute_m_n(data_clock,
 		    link_clock * nlanes * 8,
 		    &m_n->gmch_m, &m_n->gmch_n,
 		    constant_n);
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -351,7 +351,7 @@ struct intel_link_m_n {
 void intel_link_compute_m_n(u16 bpp, int nlanes,
 			    int pixel_clock, int link_clock,
 			    struct intel_link_m_n *m_n,
-			    bool constant_n);
+			    bool constant_n, bool fec_enable);
 bool is_ccs_modifier(u64 modifier);
 void lpt_disable_clkout_dp(struct drm_i915_private *dev_priv);
 u32 intel_plane_fb_max_stride(struct drm_i915_private *dev_priv,
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -76,8 +76,8 @@
 #define DP_DSC_MAX_ENC_THROUGHPUT_0		340000
 #define DP_DSC_MAX_ENC_THROUGHPUT_1		400000
 
-/* DP DSC FEC Overhead factor = (100 - 2.4)/100 */
-#define DP_DSC_FEC_OVERHEAD_FACTOR		976
+/* DP DSC FEC Overhead factor = 1/(0.972261) */
+#define DP_DSC_FEC_OVERHEAD_FACTOR		972261
 
 /* Compliance test status bits  */
 #define INTEL_DP_RESOLUTION_SHIFT_MASK	0
@@ -526,6 +526,97 @@ int intel_dp_get_link_train_fallback_val
 	return 0;
 }
 
+u32 intel_dp_mode_to_fec_clock(u32 mode_clock)
+{
+	return div_u64(mul_u32_u32(mode_clock, 1000000U),
+		       DP_DSC_FEC_OVERHEAD_FACTOR);
+}
+
+static u16 intel_dp_dsc_get_output_bpp(u32 link_clock, u32 lane_count,
+				       u32 mode_clock, u32 mode_hdisplay)
+{
+	u32 bits_per_pixel, max_bpp_small_joiner_ram;
+	int i;
+
+	/*
+	 * Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)*
+	 * (LinkSymbolClock)* 8 * (TimeSlotsPerMTP)
+	 * for SST -> TimeSlotsPerMTP is 1,
+	 * for MST -> TimeSlotsPerMTP has to be calculated
+	 */
+	bits_per_pixel = (link_clock * lane_count * 8) /
+			 intel_dp_mode_to_fec_clock(mode_clock);
+	DRM_DEBUG_KMS("Max link bpp: %u\n", bits_per_pixel);
+
+	/* Small Joiner Check: output bpp <= joiner RAM (bits) / Horiz. width */
+	max_bpp_small_joiner_ram = DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER / mode_hdisplay;
+	DRM_DEBUG_KMS("Max small joiner bpp: %u\n", max_bpp_small_joiner_ram);
+
+	/*
+	 * Greatest allowed DSC BPP = MIN (output BPP from available Link BW
+	 * check, output bpp from small joiner RAM check)
+	 */
+	bits_per_pixel = min(bits_per_pixel, max_bpp_small_joiner_ram);
+
+	/* Error out if the max bpp is less than smallest allowed valid bpp */
+	if (bits_per_pixel < valid_dsc_bpp[0]) {
+		DRM_DEBUG_KMS("Unsupported BPP %u, min %u\n",
+			      bits_per_pixel, valid_dsc_bpp[0]);
+		return 0;
+	}
+
+	/* Find the nearest match in the array of known BPPs from VESA */
+	for (i = 0; i < ARRAY_SIZE(valid_dsc_bpp) - 1; i++) {
+		if (bits_per_pixel < valid_dsc_bpp[i + 1])
+			break;
+	}
+	bits_per_pixel = valid_dsc_bpp[i];
+
+	/*
+	 * Compressed BPP in U6.4 format so multiply by 16, for Gen 11,
+	 * fractional part is 0
+	 */
+	return bits_per_pixel << 4;
+}
+
+static u8 intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp,
+				       int mode_clock, int mode_hdisplay)
+{
+	u8 min_slice_count, i;
+	int max_slice_width;
+
+	if (mode_clock <= DP_DSC_PEAK_PIXEL_RATE)
+		min_slice_count = DIV_ROUND_UP(mode_clock,
+					       DP_DSC_MAX_ENC_THROUGHPUT_0);
+	else
+		min_slice_count = DIV_ROUND_UP(mode_clock,
+					       DP_DSC_MAX_ENC_THROUGHPUT_1);
+
+	max_slice_width = drm_dp_dsc_sink_max_slice_width(intel_dp->dsc_dpcd);
+	if (max_slice_width < DP_DSC_MIN_SLICE_WIDTH_VALUE) {
+		DRM_DEBUG_KMS("Unsupported slice width %d by DP DSC Sink device\n",
+			      max_slice_width);
+		return 0;
+	}
+	/* Also take into account max slice width */
+	min_slice_count = min_t(u8, min_slice_count,
+				DIV_ROUND_UP(mode_hdisplay,
+					     max_slice_width));
+
+	/* Find the closest match to the valid slice count values */
+	for (i = 0; i < ARRAY_SIZE(valid_dsc_slicecount); i++) {
+		if (valid_dsc_slicecount[i] >
+		    drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
+						    false))
+			break;
+		if (min_slice_count  <= valid_dsc_slicecount[i])
+			return valid_dsc_slicecount[i];
+	}
+
+	DRM_DEBUG_KMS("Unsupported Slice Count %d\n", min_slice_count);
+	return 0;
+}
+
 static enum drm_mode_status
 intel_dp_mode_valid(struct drm_connector *connector,
 		    struct drm_display_mode *mode)
@@ -2248,7 +2339,7 @@ intel_dp_compute_config(struct intel_enc
 			       adjusted_mode->crtc_clock,
 			       pipe_config->port_clock,
 			       &pipe_config->dp_m_n,
-			       constant_n);
+			       constant_n, pipe_config->fec_enable);
 
 	if (intel_connector->panel.downclock_mode != NULL &&
 		dev_priv->drrs.type == SEAMLESS_DRRS_SUPPORT) {
@@ -2258,7 +2349,7 @@ intel_dp_compute_config(struct intel_enc
 					       intel_connector->panel.downclock_mode->clock,
 					       pipe_config->port_clock,
 					       &pipe_config->dp_m2_n2,
-					       constant_n);
+					       constant_n, pipe_config->fec_enable);
 	}
 
 	if (!HAS_DDI(dev_priv))
@@ -4345,91 +4436,6 @@ intel_dp_get_sink_irq_esi(struct intel_d
 		DP_DPRX_ESI_LEN;
 }
 
-u16 intel_dp_dsc_get_output_bpp(int link_clock, u8 lane_count,
-				int mode_clock, int mode_hdisplay)
-{
-	u16 bits_per_pixel, max_bpp_small_joiner_ram;
-	int i;
-
-	/*
-	 * Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)*
-	 * (LinkSymbolClock)* 8 * ((100-FECOverhead)/100)*(TimeSlotsPerMTP)
-	 * FECOverhead = 2.4%, for SST -> TimeSlotsPerMTP is 1,
-	 * for MST -> TimeSlotsPerMTP has to be calculated
-	 */
-	bits_per_pixel = (link_clock * lane_count * 8 *
-			  DP_DSC_FEC_OVERHEAD_FACTOR) /
-		mode_clock;
-
-	/* Small Joiner Check: output bpp <= joiner RAM (bits) / Horiz. width */
-	max_bpp_small_joiner_ram = DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER /
-		mode_hdisplay;
-
-	/*
-	 * Greatest allowed DSC BPP = MIN (output BPP from avaialble Link BW
-	 * check, output bpp from small joiner RAM check)
-	 */
-	bits_per_pixel = min(bits_per_pixel, max_bpp_small_joiner_ram);
-
-	/* Error out if the max bpp is less than smallest allowed valid bpp */
-	if (bits_per_pixel < valid_dsc_bpp[0]) {
-		DRM_DEBUG_KMS("Unsupported BPP %d\n", bits_per_pixel);
-		return 0;
-	}
-
-	/* Find the nearest match in the array of known BPPs from VESA */
-	for (i = 0; i < ARRAY_SIZE(valid_dsc_bpp) - 1; i++) {
-		if (bits_per_pixel < valid_dsc_bpp[i + 1])
-			break;
-	}
-	bits_per_pixel = valid_dsc_bpp[i];
-
-	/*
-	 * Compressed BPP in U6.4 format so multiply by 16, for Gen 11,
-	 * fractional part is 0
-	 */
-	return bits_per_pixel << 4;
-}
-
-u8 intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp,
-				int mode_clock,
-				int mode_hdisplay)
-{
-	u8 min_slice_count, i;
-	int max_slice_width;
-
-	if (mode_clock <= DP_DSC_PEAK_PIXEL_RATE)
-		min_slice_count = DIV_ROUND_UP(mode_clock,
-					       DP_DSC_MAX_ENC_THROUGHPUT_0);
-	else
-		min_slice_count = DIV_ROUND_UP(mode_clock,
-					       DP_DSC_MAX_ENC_THROUGHPUT_1);
-
-	max_slice_width = drm_dp_dsc_sink_max_slice_width(intel_dp->dsc_dpcd);
-	if (max_slice_width < DP_DSC_MIN_SLICE_WIDTH_VALUE) {
-		DRM_DEBUG_KMS("Unsupported slice width %d by DP DSC Sink device\n",
-			      max_slice_width);
-		return 0;
-	}
-	/* Also take into account max slice width */
-	min_slice_count = min_t(u8, min_slice_count,
-				DIV_ROUND_UP(mode_hdisplay,
-					     max_slice_width));
-
-	/* Find the closest match to the valid slice count values */
-	for (i = 0; i < ARRAY_SIZE(valid_dsc_slicecount); i++) {
-		if (valid_dsc_slicecount[i] >
-		    drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
-						    false))
-			break;
-		if (min_slice_count  <= valid_dsc_slicecount[i])
-			return valid_dsc_slicecount[i];
-	}
-
-	DRM_DEBUG_KMS("Unsupported Slice Count %d\n", min_slice_count);
-	return 0;
-}
-
 static void
 intel_pixel_encoding_setup_vsc(struct intel_dp *intel_dp,
 			       const struct intel_crtc_state *crtc_state)
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -102,10 +102,6 @@ bool intel_dp_source_supports_hbr2(struc
 bool intel_dp_source_supports_hbr3(struct intel_dp *intel_dp);
 bool
 intel_dp_get_link_status(struct intel_dp *intel_dp, u8 *link_status);
-u16 intel_dp_dsc_get_output_bpp(int link_clock, u8 lane_count,
-				int mode_clock, int mode_hdisplay);
-u8 intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp, int mode_clock,
-				int mode_hdisplay);
 
 bool intel_dp_read_dpcd(struct intel_dp *intel_dp);
 bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);
@@ -120,4 +116,6 @@ static inline unsigned int intel_dp_unus
 	return ~((1 << lane_count) - 1) & 0xf;
 }
 
+u32 intel_dp_mode_to_fec_clock(u32 mode_clock);
+
 #endif /* __INTEL_DP_H__ */
--- a/drivers/gpu/drm/i915/display/intel_dp_mst.c
+++ b/drivers/gpu/drm/i915/display/intel_dp_mst.c
@@ -81,7 +81,7 @@ static int intel_dp_mst_compute_link_con
 			       adjusted_mode->crtc_clock,
 			       crtc_state->port_clock,
 			       &crtc_state->dp_m_n,
-			       constant_n);
+			       constant_n, crtc_state->fec_enable);
 	crtc_state->dp_m_n.tu = slots;
 
 	return 0;