From: Stephen Hemminger <stephen@networkplumber.org>
To: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Subject: [ANNOUNCE] iproute2 5.4
Date: Mon, 25 Nov 2019 08:17:37 -0800 [thread overview]
Message-ID: <20191125081737.2ff4a7ca@hermes.lan> (raw)
The 5.4 kernel has been released, and the last patches have
been applied to iproute2.
Not a lot of changes in this release, most are related to fixing output
formatting and documentation.
Download:
https://www.kernel.org/pub/linux/utils/net/iproute2/iproute2-5.4.0.tar.gz
Repository for upcoming release:
git://git.kernel.org/pub/scm/network/iproute2/iproute2.git
And future release (net-next):
git://git.kernel.org/pub/scm/network/iproute2/iproute2-next.git
Thanks for all the contributions.
Report problems (or enhancements) to the netdev@vger.kernel.org mailing list.
---
Andrea Claudi (4):
tunnel: factorize printout of GRE key and flags
ip tunnel: add json output
bpf: replace snprintf with asprintf when dealing with long buffers
tc: fix segmentation fault on gact action
Aya Levin (3):
devlink: Add helper for left justification print
devlink: Left justification on FMSG output
devlink: Fix inconsistency between command input and output
Damien Robert (1):
man: add reference to `ip route add encap ... src`
David Ahern (3):
Import tc_act/tc_ct.h uapi file
Update kernel headers
Update kernel headers
David Dai (1):
iproute2-next: police: support 64bit rate and peakrate in tc utility
Dirk van der Merwe (2):
devlink: add 'reset_dev_on_drv_probe' devlink param
devlink: unknown 'fw_load_policy' string validation
Donald Sharp (1):
ip nexthop: Allow flush|list operations to specify a specific protocol
Eli Britstein (5):
tc_util: introduce a function to print JSON/non-JSON masked numbers
tc_util: add an option to print masked numbers with/without a newline
tc: flower: fix newline prints for ct-mark and ct-zone
tc_util: fix JSON prints for ct-mark and ct-zone
tc: flower: fix output for ip tos and ttl
Florent Fourcot (1):
man: remove "defaut group" sentence on ip link
Gal Pressman (1):
rdma: Add driver QP type string
Guillaume Nault (1):
man: remove ppp from list of devices not allowed to change netns
Hritik Vijay (1):
ss: show header for --processes/-p
Ido Schimmel (4):
devlink: Increase number of supported options
devlink: Add devlink trap set and show commands
devlink: Add devlink trap group set and show commands
devlink: Add man page for devlink-trap
Jakub Kicinski (1):
devlink: require resource parameters
Jiri Pirko (3):
devlink: implement flash update status monitoring
devlink: implement flash status monitoring
devlink: add reload failed indication
Julien Fortin (1):
ip: fix ip route show json output for multipath nexthops
Michał Łyszczek (3):
ipnetns: do not check netns NAME when -all is specified
rdma/sys.c: fix possible out-of-bound array access
libnetlink.c, ss.c: properly handle fread() errors
Nicolas Dichtel (3):
ipnetns: enable to dump nsid conversion table
ip-netns.8: document the 'auto' keyword of 'ip netns set'
ip-netns.8: document target-nsid and nsid options of list-id
Paul Blakey (3):
tc: add NLA_F_NESTED flag to all actions options nested block
tc: Introduce tc ct action
tc: flower: Add matching on conntrack info
Roman Mashak (2):
man: tc-ematch.8: update list of filter using extended matches
man: tc-ematch.8: documented canid() ematch rule
Stephen Hemminger (12):
uapi: update headers from 5.4-rc
uapi: update btf from 5.4-rc1
examples: remove out of date cbq stuff
examples: remove gaiconf
examples: remove diffserv
remove out of date README
don't install examples
uapi: SPDX license updates
uapi: devlink.h health timestamp
remove no longer useful README for lnstat
netem: remove redundant README
v5.4.0
Thomas Haller (1):
man: add note to ip-macsec manual about necessary key management
Vedang Patel (4):
etf: Add skip_sock_check
taprio: add support for setting txtime_delay.
tc: etf: Add documentation for skip_sock_check.
tc: taprio: Update documentation
Vinicius Costa Gomes (1):
taprio: Add support for setting flags
Vlad Buslov (1):
tc: remove duplicated NEXT_ARG_FWD() in parse_ct()
next reply other threads:[~2019-11-25 16:17 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-25 16:17 Stephen Hemminger [this message]
2019-11-25 19:21 ` [ANNOUNCE] iproute2 5.4 Christian Hesse
2019-11-25 20:11 ` Stephen Hemminger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191125081737.2ff4a7ca@hermes.lan \
--to=stephen@networkplumber.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.