From: Patrice Chotard <patrice.chotard@st.com>
To: u-boot@lists.denx.de
Subject: [PATCH v1 2/2] treewide: Remove CONFIG_SYS_UBOOT_START from configs board files
Date: Fri, 6 Dec 2019 15:01:49 +0100 [thread overview]
Message-ID: <20191206140149.7426-3-patrice.chotard@st.com> (raw)
In-Reply-To: <20191206140149.7426-1-patrice.chotard@st.com>
As previous CONFIG_SYS_UBOOT_START is now set by default to
CONFIG_SYS_TEXT_BASE when not defined, CONFIG_SYS_UBOOT_START
can be removed from include/configs board files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
include/configs/gardena-smart-gateway-at91sam.h | 1 -
include/configs/ls1046a_common.h | 1 -
include/configs/mccmon6.h | 1 -
include/configs/microblaze-generic.h | 2 --
include/configs/mt7623.h | 1 -
include/configs/mt7629.h | 1 -
include/configs/mt8518.h | 1 -
include/configs/omap3_cairo.h | 1 -
include/configs/pumpkin.h | 1 -
include/configs/tegra-common.h | 1 -
include/configs/x600.h | 1 -
include/configs/xilinx_zynqmp_r5.h | 2 --
include/configs/zynq-common.h | 2 --
13 files changed, 16 deletions(-)
diff --git a/include/configs/gardena-smart-gateway-at91sam.h b/include/configs/gardena-smart-gateway-at91sam.h
index 482e4714b1..f5ee65cb8a 100644
--- a/include/configs/gardena-smart-gateway-at91sam.h
+++ b/include/configs/gardena-smart-gateway-at91sam.h
@@ -64,7 +64,6 @@
#define CONFIG_SPL_NAND_RAW_ONLY
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0xa0000
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
index cc8f4c0210..6543cfd868 100644
--- a/include/configs/ls1046a_common.h
+++ b/include/configs/ls1046a_common.h
@@ -98,7 +98,6 @@
CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SYS_MONITOR_LEN 0x100000
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#endif
/* NAND SPL */
diff --git a/include/configs/mccmon6.h b/include/configs/mccmon6.h
index 045a9f7bdf..0aee1e1cf6 100644
--- a/include/configs/mccmon6.h
+++ b/include/configs/mccmon6.h
@@ -12,7 +12,6 @@
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#include "imx6_spl.h"
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h
index 385b30c99b..8ca0e83c78 100644
--- a/include/configs/microblaze-generic.h
+++ b/include/configs/microblaze-generic.h
@@ -173,8 +173,6 @@
/* Just for sure that there is a space for stack */
#define CONFIG_SPL_STACK_SIZE 0x100
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-
#define CONFIG_SPL_MAX_FOOTPRINT (CONFIG_SYS_INIT_RAM_SIZE - \
CONFIG_SYS_INIT_RAM_ADDR - \
CONFIG_SYS_MALLOC_F_LEN - \
diff --git a/include/configs/mt7623.h b/include/configs/mt7623.h
index e5182aeea8..faab0913fc 100644
--- a/include/configs/mt7623.h
+++ b/include/configs/mt7623.h
@@ -31,7 +31,6 @@
#define CONFIG_ENV_OVERWRITE
/* Preloader -> Uboot */
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + SZ_2M - \
GENERATED_GBL_DATA_SIZE)
diff --git a/include/configs/mt7629.h b/include/configs/mt7629.h
index 4aef894c6e..6a6c2f2414 100644
--- a/include/configs/mt7629.h
+++ b/include/configs/mt7629.h
@@ -40,7 +40,6 @@
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SPI_ADDR + CONFIG_SPL_PAD_TO)
/* SPL -> Uboot */
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + SZ_2M - \
GENERATED_GBL_DATA_SIZE)
diff --git a/include/configs/mt8518.h b/include/configs/mt8518.h
index a7fe83a605..514722be99 100644
--- a/include/configs/mt8518.h
+++ b/include/configs/mt8518.h
@@ -29,7 +29,6 @@
#define CONFIG_SYS_BOOTM_LEN SZ_64M
/* Uboot definition */
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + \
SZ_2M - \
GENERATED_GBL_DATA_SIZE)
diff --git a/include/configs/omap3_cairo.h b/include/configs/omap3_cairo.h
index 1b1a56d7cd..c76c81ddd5 100644
--- a/include/configs/omap3_cairo.h
+++ b/include/configs/omap3_cairo.h
@@ -26,7 +26,6 @@
* other needs. We use this rather than the inherited defines from
* ti_armv7_common.h for backwards compatibility.
*/
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
diff --git a/include/configs/pumpkin.h b/include/configs/pumpkin.h
index 35e28be950..9c52cae41d 100644
--- a/include/configs/pumpkin.h
+++ b/include/configs/pumpkin.h
@@ -23,7 +23,6 @@
#define CONFIG_SYS_NS16550_COM1 0x11005000
#define CONFIG_SYS_NS16550_CLK 26000000
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + SZ_2M - \
GENERATED_GBL_DATA_SIZE)
diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h
index b4da1f8428..f2cdd9c019 100644
--- a/include/configs/tegra-common.h
+++ b/include/configs/tegra-common.h
@@ -61,7 +61,6 @@
#define PHYS_SDRAM_1 NV_PA_SDRC_CS0
#define PHYS_SDRAM_1_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* 256M */
diff --git a/include/configs/x600.h b/include/configs/x600.h
index 63092b24a5..8b6caae7be 100644
--- a/include/configs/x600.h
+++ b/include/configs/x600.h
@@ -27,7 +27,6 @@
#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \
CONFIG_SYS_SPL_LEN)
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x60000
diff --git a/include/configs/xilinx_zynqmp_r5.h b/include/configs/xilinx_zynqmp_r5.h
index 38d952d0c0..155d7fe883 100644
--- a/include/configs/xilinx_zynqmp_r5.h
+++ b/include/configs/xilinx_zynqmp_r5.h
@@ -35,8 +35,6 @@
/* Extend size of kernel image for uncompression */
#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-
#define CONFIG_SKIP_LOWLEVEL_INIT
/* 0x0 - 0x40 is used for placing exception vectors */
diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 274cc19112..189ca81bbe 100644
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -274,6 +274,4 @@
#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-
#endif /* __CONFIG_ZYNQ_COMMON_H */
--
2.17.1
next prev parent reply other threads:[~2019-12-06 14:01 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-06 14:01 [RFT][PATCH v1 0/2] Fix CONFIG_SYS_UBOOT_START default value Patrice Chotard
2019-12-06 14:01 ` [PATCH v1 1/2] Makefile: " Patrice Chotard
2019-12-30 1:21 ` Simon Glass
2020-01-08 20:12 ` Tom Rini
2019-12-06 14:01 ` Patrice Chotard [this message]
2019-12-08 14:24 ` [PATCH v1 2/2] treewide: Remove CONFIG_SYS_UBOOT_START from configs board files Lukasz Majewski
2020-01-08 20:13 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191206140149.7426-3-patrice.chotard@st.com \
--to=patrice.chotard@st.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.