From: Dave Chinner <david@fromorbit.com>
To: Brian Foster <bfoster@redhat.com>
Cc: linux-xfs@vger.kernel.org
Subject: Re: [PATCH] xfs: stabilize insert range start boundary to avoid COW writeback race
Date: Fri, 13 Dec 2019 07:48:51 +1100 [thread overview]
Message-ID: <20191212204851.GF19256@dread.disaster.area> (raw)
In-Reply-To: <20191212141634.GA36655@bfoster>
On Thu, Dec 12, 2019 at 09:16:34AM -0500, Brian Foster wrote:
> On Thu, Dec 12, 2019 at 07:52:30AM +1100, Dave Chinner wrote:
> > On Wed, Dec 11, 2019 at 07:47:12AM -0500, Brian Foster wrote:
> > > On Wed, Dec 11, 2019 at 08:41:00AM +1100, Dave Chinner wrote:
> > > > On Tue, Dec 10, 2019 at 08:23:40AM -0500, Brian Foster wrote:
> > > > I think insert/collapse need to be converted to work like a
> > > > truncate operation instead of a series on individual write
> > > > operations. That is, they are a permanent transaction that locks the
> > > > inode once and is rolled repeatedly until the entire extent listi
> > > > modification is done and then the inode is unlocked.
> > > >
> > >
> > > Note that I don't think it's sufficient to hold the inode locked only
> > > across the shift. For the insert case, I think we'd need to grab it
> > > before the extent split at the target offset and roll from there.
> > > Otherwise the same problem could be reintroduced if we eventually
> > > replaced the xfs_prepare_shift() tweak made by this patch. Of course,
> > > that doesn't look like a big problem. The locking is already elevated
> > > and split and shift even use the same transaction type, so it's mostly a
> > > refactor from a complexity standpoint.
> >
> > *nod*
> >
> > > For the collapse case, we do have a per-shift quota reservation for some
> > > reason. If that is required, we'd have to somehow replace it with a
> > > worst case calculation. That said, it's not clear to me why that
> > > reservation even exists.
> >
> > I'm not 100% sure, either, but....
> >
> > > The pre-shift hole punch is already a separate
> > > transaction with its own such reservation. The shift can merge extents
> > > after that point (though most likely only on the first shift), but that
> > > would only ever remove extent records. Any thoughts or objections if I
> > > just killed that off?
> >
> > Yeah, I suspect that it is the xfs_bmse_merge() case freeing blocks
> > the reservation is for, and I agree that it should only happen on
> > the first shift because all the others that are moved are identical
> > in size and shape and would have otherwise been merged at creation.
> >
> > Hence I think we can probably kill the xfs_bmse_merge() case,
> > though it might be wrth checking first how often it gets called...
> >
>
> Ok, but do we need an up-front quota reservation for freeing blocks out
> of the bmapbt? ISTM the reservation could be removed regardless of the
> merging behavior. This is what my current patch does, at least, so we'll
> see if anything explodes. :P
xfs_itruncate_extents() doesn't require an up front block
reservation for quotas or transaction allocation, so I don't really
see how the collapse would require it, even in the merge case...
> I agree on the xfs_bmse_merge() bit. I was planning to leave that as is
> however because IIRC, even though it is quite rare, I thought we had a
> few corner cases where it was possible for physically and logically
> contiguous extents to track separately in a mapping tree. Max sized
> extents that are subsequently punched out or truncated might be one
> example. I thought we had others, but I can't quite put my finger on it
> atm..
True, but is it common enough that we really need to care about it?
If it's bad, just run xfs_fsr on the file/filesystem....
Cheers,
Dave.
--
Dave Chinner
david@fromorbit.com
next prev parent reply other threads:[~2019-12-12 20:48 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-10 13:23 [PATCH] xfs: stabilize insert range start boundary to avoid COW writeback race Brian Foster
2019-12-10 14:02 ` Carlos Maiolino
2019-12-10 21:41 ` Dave Chinner
2019-12-11 12:47 ` Brian Foster
2019-12-11 20:52 ` Dave Chinner
2019-12-12 14:16 ` Brian Foster
2019-12-12 20:48 ` Dave Chinner [this message]
2019-12-13 11:37 ` Brian Foster
2019-12-17 5:59 ` Darrick J. Wong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191212204851.GF19256@dread.disaster.area \
--to=david@fromorbit.com \
--cc=bfoster@redhat.com \
--cc=linux-xfs@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.