From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Cc: adrian.hunter@intel.com, ulf.hansson@linaro.org,
robh+dt@kernel.org, mka@chromium.org, linux-mmc@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org,
Veerabhadrarao Badiganti <vbadigan@codeaurora.org>,
Andy Gross <agross@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Subject: Re: [PATCH V3] arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
Date: Thu, 13 Feb 2020 21:30:53 -0800 [thread overview]
Message-ID: <20200214053053.GV3948@builder> (raw)
In-Reply-To: <1578495250-10672-1-git-send-email-sbhanu@codeaurora.org>
On Wed 08 Jan 06:54 PST 2020, Shaik Sajida Bhanu wrote:
> From: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
>
> Add sdhc instances for supporting eMMC and SD-card on sc7180.
> The regulators should be in HPM state for proper functionality of
> eMMC and SD-card. Updating corresponding regulators accordingly.
>
> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
> Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Applied
Regards,
Bjorn
> ---
> Changes since V2:
> - Added cmdq register space and support-cqe flag.
> - Incorporated review comments by Matthias Kaehlcke.
>
> Changes since V1:
> - Updated the regulator min, max voltages as per
> eMMC/SD-card voltage requirements
> - Enabled IOMMU for eMMC and SD-card.
> - Added pull and drive strength to SD-card cd-gpio.
> - Incorporated review comments by Matthias Kaehlcke.
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++
> 2 files changed, 183 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 388f50a..a790d82 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -7,6 +7,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> #include "sc7180.dtsi"
> #include "pm6150.dtsi"
> @@ -101,9 +102,9 @@
> };
>
> vreg_l12a_1p8: ldo12 {
> - regulator-min-microvolt = <1696000>;
> - regulator-max-microvolt = <1952000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l13a_1p8: ldo13 {
> @@ -143,9 +144,9 @@
> };
>
> vreg_l19a_2p9: ldo19 {
> - regulator-min-microvolt = <2696000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
> };
>
> @@ -189,9 +190,9 @@
> };
>
> vreg_l6c_2p9: ldo6 {
> - regulator-min-microvolt = <2696000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l7c_3p0: ldo7 {
> @@ -207,9 +208,9 @@
> };
>
> vreg_l9c_2p9: ldo9 {
> - regulator-min-microvolt = <2952000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l10c_3p3: ldo10 {
> @@ -254,6 +255,28 @@
> status = "okay";
> };
>
> +&sdhc_1 {
> + status = "okay";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_on>;
> + pinctrl-1 = <&sdc1_off>;
> + vmmc-supply = <&vreg_l19a_2p9>;
> + vqmmc-supply = <&vreg_l12a_1p8>;
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default","sleep";
> + pinctrl-0 = <&sdc2_on>;
> + pinctrl-1 = <&sdc2_off>;
> + vmmc-supply = <&vreg_l9c_2p9>;
> + vqmmc-supply = <&vreg_l6c_2p9>;
> +
> + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
> +};
> +
> &uart3 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 3676bfd..525bc02 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -226,6 +226,33 @@
> };
> };
>
> + sdhc_1: sdhci@7c4000 {
> + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> + reg = <0 0x7c4000 0 0x1000>,
> + <0 0x07c5000 0 0x1000>;
> + reg-names = "hc_mem", "cqhci_mem";
> +
> + iommus = <&apps_smmu 0x60 0x0>;
> + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&gcc GCC_SDCC1_APPS_CLK>,
> + <&gcc GCC_SDCC1_AHB_CLK>;
> + clock-names = "core", "iface";
> +
> + bus-width = <8>;
> + non-removable;
> + supports-cqe;
> +
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + mmc-hs400-enhanced-strobe;
> +
> + status = "disabled";
> + };
> +
> qupv3_id_0: geniqup@8c0000 {
> compatible = "qcom,geni-se-qup";
> reg = <0 0x008c0000 0 0x6000>;
> @@ -929,6 +956,127 @@
> function = "qup15";
> };
> };
> +
> + sdc1_on: sdc1-on {
> + pinconf-clk {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + pinconf-cmd {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + pinconf-data {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + pinconf-rclk {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + sdc1_off: sdc1-off {
> + pinconf-clk {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
> + pinconf-cmd {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + pinconf-data {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + pinconf-rclk {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + sdc2_on: sdc2-on {
> + pinconf-clk {
> + pins = "sdc2_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + pinconf-cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + pinconf-data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + pinconf-sd-cd {
> + pins = "gpio69";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + sdc2_off: sdc2-off {
> + pinconf-clk {
> + pins = "sdc2_clk";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
> + pinconf-cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + pinconf-data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +
> + pinconf-sd-cd {
> + pins = "gpio69";
> + bias-disable;
> + drive-strength = <2>;
> + };
> + };
> + };
> +
> + sdhc_2: sdhci@8804000 {
> + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> + reg = <0 0x08804000 0 0x1000>;
> + reg-names = "hc_mem";
> +
> + iommus = <&apps_smmu 0x80 0>;
> + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&gcc GCC_SDCC2_APPS_CLK>,
> + <&gcc GCC_SDCC2_AHB_CLK>;
> + clock-names = "core", "iface";
> +
> + bus-width = <4>;
> +
> + status = "disabled";
> };
>
> qspi: spi@88dc000 {
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
prev parent reply other threads:[~2020-02-14 5:31 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-08 14:54 [PATCH V3] arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card Shaik Sajida Bhanu
2020-02-11 14:29 ` Veerabhadrarao Badiganti
2020-02-11 15:13 ` Ulf Hansson
2020-02-14 5:30 ` Bjorn Andersson [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200214053053.GV3948@builder \
--to=bjorn.andersson@linaro.org \
--cc=adrian.hunter@intel.com \
--cc=agross@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
--cc=sbhanu@codeaurora.org \
--cc=ulf.hansson@linaro.org \
--cc=vbadigan@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.