From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To: Jarkko Nikula <jarkko.nikula@linux.intel.com>,
Mika Westerberg <mika.westerberg@linux.intel.com>,
linux-i2c@vger.kernel.org,
Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Subject: [PATCH v2 3/5] i2c: designware: Switch PCI driver to use i2c_dw_configure_master()
Date: Sat, 25 Apr 2020 16:44:46 +0300 [thread overview]
Message-ID: <20200425134448.28514-3-andriy.shevchenko@linux.intel.com> (raw)
In-Reply-To: <20200425134448.28514-1-andriy.shevchenko@linux.intel.com>
Since we have available helper to configure master mode, let's use it
in the PCI driver instead of spread open-coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
v2: new patch
drivers/i2c/busses/i2c-designware-pcidrv.c | 33 +++++-----------------
1 file changed, 7 insertions(+), 26 deletions(-)
diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c
index 7a0b65b5b5b59..d5e5abc03683f 100644
--- a/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ b/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -46,20 +46,14 @@ struct dw_scl_sda_cfg {
struct dw_pci_controller {
u32 bus_num;
- u32 bus_cfg;
u32 tx_fifo_depth;
u32 rx_fifo_depth;
u32 clk_khz;
- u32 functionality;
u32 flags;
struct dw_scl_sda_cfg *scl_sda_cfg;
int (*setup)(struct pci_dev *pdev, struct dw_pci_controller *c);
};
-#define INTEL_MID_STD_CFG (DW_IC_CON_MASTER | \
- DW_IC_CON_SLAVE_DISABLE | \
- DW_IC_CON_RESTART_EN)
-
/* Merrifield HCNT/LCNT/SDA hold time */
static struct dw_scl_sda_cfg mrfld_config = {
.ss_hcnt = 0x2f8,
@@ -88,10 +82,11 @@ static struct dw_scl_sda_cfg hsw_config = {
static int mfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
{
+ struct dw_i2c_dev *dev = dev_get_drvdata(&pdev->dev);
+
switch (pdev->device) {
case 0x0817:
- c->bus_cfg &= ~DW_IC_CON_SPEED_MASK;
- c->bus_cfg |= DW_IC_CON_SPEED_STD;
+ dev->timings.bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ;
/* fall through */
case 0x0818:
case 0x0819:
@@ -128,53 +123,41 @@ static int mrfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
static struct dw_pci_controller dw_pci_controllers[] = {
[medfield] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 32,
.rx_fifo_depth = 32,
- .functionality = I2C_FUNC_10BIT_ADDR,
.clk_khz = 25000,
.setup = mfld_setup,
},
[merrifield] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 64,
.rx_fifo_depth = 64,
- .functionality = I2C_FUNC_10BIT_ADDR,
.scl_sda_cfg = &mrfld_config,
.setup = mrfld_setup,
},
[baytrail] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 32,
.rx_fifo_depth = 32,
- .functionality = I2C_FUNC_10BIT_ADDR,
.scl_sda_cfg = &byt_config,
},
[haswell] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 32,
.rx_fifo_depth = 32,
- .functionality = I2C_FUNC_10BIT_ADDR,
.scl_sda_cfg = &hsw_config,
},
[cherrytrail] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 32,
.rx_fifo_depth = 32,
- .functionality = I2C_FUNC_10BIT_ADDR,
.flags = MODEL_CHERRYTRAIL,
.scl_sda_cfg = &byt_config,
},
[elkhartlake] = {
.bus_num = -1,
- .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
.tx_fifo_depth = 32,
.rx_fifo_depth = 32,
- .functionality = I2C_FUNC_10BIT_ADDR,
.clk_khz = 100000,
},
};
@@ -250,14 +233,16 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
if (r < 0)
return r;
- dev->clk = NULL;
dev->controller = controller;
dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
+ dev->timings.bus_freq_hz = I2C_MAX_FAST_MODE_FREQ;
dev->base = pcim_iomap_table(pdev)[0];
dev->dev = &pdev->dev;
dev->irq = pci_irq_vector(pdev, 0);
dev->flags |= controller->flags;
+ pci_set_drvdata(pdev, dev);
+
if (controller->setup) {
r = controller->setup(pdev, controller);
if (r) {
@@ -266,10 +251,8 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
}
}
- dev->functionality = controller->functionality |
- DW_IC_DEFAULT_FUNCTIONALITY;
+ i2c_dw_configure_master(dev);
- dev->master_cfg = controller->bus_cfg;
if (controller->scl_sda_cfg) {
cfg = controller->scl_sda_cfg;
dev->ss_hcnt = cfg->ss_hcnt;
@@ -279,8 +262,6 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
dev->sda_hold_time = cfg->sda_hold;
}
- pci_set_drvdata(pdev, dev);
-
dev->tx_fifo_depth = controller->tx_fifo_depth;
dev->rx_fifo_depth = controller->rx_fifo_depth;
--
2.26.2
next prev parent reply other threads:[~2020-04-25 13:45 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-25 13:44 [PATCH v2 1/5] i2c: designware: Use devm_platform_ioremap_resource() to simplify code Andy Shevchenko
2020-04-25 13:44 ` [PATCH v2 2/5] i2c: designware: Move configuration routines to respective modules Andy Shevchenko
2020-04-25 13:44 ` Andy Shevchenko [this message]
2020-04-25 13:44 ` [PATCH v2 4/5] i2c: designware: Rename i2c_dw_probe() to i2c_dw_probe_master() Andy Shevchenko
2020-04-25 13:44 ` [PATCH v2 5/5] i2c: designware: Allow slave mode for PCI enumerated devices Andy Shevchenko
2020-04-27 14:05 ` Jarkko Nikula
2020-04-28 22:18 ` Wolfram Sang
2020-05-12 16:14 ` Andy Shevchenko
2020-05-12 16:22 ` Wolfram Sang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200425134448.28514-3-andriy.shevchenko@linux.intel.com \
--to=andriy.shevchenko@linux.intel.com \
--cc=jarkko.nikula@linux.intel.com \
--cc=linux-i2c@vger.kernel.org \
--cc=mika.westerberg@linux.intel.com \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.