From: Jonathan Marek <jonathan@marek.ca>
To: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
linux-kernel@vger.kernel.org (open list:GENERIC PHY FRAMEWORK)
Subject: [PATCH 3/3] phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250
Date: Sat, 23 May 2020 22:14:15 -0400 [thread overview]
Message-ID: <20200524021416.17049-4-jonathan@marek.ca> (raw)
In-Reply-To: <20200524021416.17049-1-jonathan@marek.ca>
Add both the DP and UNI PHY for primary/secondary usb controllers.
The tables are very similar to sm8150 (serdes_tbl is identical), but there
are some differences.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 206 ++++++++++++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-qmp.h | 2 +
2 files changed, 208 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 9367f8f793b5..8a597cedfebe 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -1532,6 +1532,142 @@ static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
};
+static const struct qmp_phy_init_tbl sm8250_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_TX, 0x60),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_RX, 0x60),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x40, 1),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x54, 2),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0xff, 1),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f, 2),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f, 1),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff, 2),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x97),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0xa0),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VTH_CODE, 0x10),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xbf),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+};
+
/* struct qmp_phy_cfg - per-PHY initialization config */
struct qmp_phy_cfg {
/* phy-type - PCIE/UFS/USB */
@@ -1700,6 +1836,11 @@ static const char * const qmp_v4_phy_clk_l[] = {
"aux", "ref_clk_src", "ref", "com_aux",
};
+/* the primary usb3 phy on sm8250 doesn't have a ref clock */
+static const char * const qmp_v4_sm8250_usbphy_clk_l[] = {
+ "aux", "ref_clk_src", "com_aux"
+};
+
static const char * const sdm845_ufs_phy_clk_l[] = {
"ref", "ref_aux",
};
@@ -2147,6 +2288,65 @@ static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
};
+static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = sm8150_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_serdes_tbl),
+ .tx_tbl = sm8250_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm8250_usb3_tx_tbl),
+ .rx_tbl = sm8250_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm8250_usb3_rx_tbl),
+ .pcs_tbl = sm8250_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8250_usb3_pcs_tbl),
+ .clk_list = qmp_v4_sm8250_usbphy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v4_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .is_dual_lane_phy = true,
+};
+
+static const struct qmp_phy_cfg sm8250_usb3_uniphy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = sm8150_usb3_uniphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+ .tx_tbl = sm8250_usb3_uniphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_tx_tbl),
+ .rx_tbl = sm8250_usb3_uniphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_rx_tbl),
+ .pcs_tbl = sm8250_usb3_uniphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_pcs_tbl),
+ .clk_list = qmp_v4_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v4_usb3_uniphy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
static void qcom_qmp_phy_configure_lane(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
@@ -2924,6 +3124,12 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
}, {
.compatible = "qcom,sm8150-qmp-usb3-uni-phy",
.data = &sm8150_usb3_uniphy_cfg,
+ }, {
+ .compatible = "qcom,sm8250-qmp-usb3-phy",
+ .data = &sm8250_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,sm8250-qmp-usb3-uni-phy",
+ .data = &sm8250_usb3_uniphy_cfg,
},
{ },
};
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index f39f7a968228..4277f592684b 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -364,7 +364,9 @@
#define QSERDES_V4_TX_RES_CODE_LANE_TX 0x34
#define QSERDES_V4_TX_RES_CODE_LANE_RX 0x38
#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 0x3c
+#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX 0x40
#define QSERDES_V4_TX_LANE_MODE_1 0x84
+#define QSERDES_V4_TX_LANE_MODE_2 0x88
#define QSERDES_V4_TX_RCV_DETECT_LVL_2 0x9c
#define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1 0xd8
#define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1 0xdC
--
2.26.1
next prev parent reply other threads:[~2020-05-24 2:14 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-24 2:14 [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Jonathan Marek
2020-05-24 2:14 ` [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane Jonathan Marek
2020-06-25 19:41 ` Dmitry Baryshkov
2020-06-26 7:35 ` Bjorn Andersson
2020-05-24 2:14 ` [PATCH 2/3] phy: qcom-qmp: Add QMP V4 USB3 UNIPHY Jonathan Marek
2020-06-25 19:42 ` Dmitry Baryshkov
2020-06-26 7:37 ` Bjorn Andersson
2020-05-24 2:14 ` Jonathan Marek [this message]
2020-06-25 19:42 ` [PATCH 3/3] phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250 Dmitry Baryshkov
2020-06-26 7:40 ` Bjorn Andersson
2020-06-29 9:41 ` [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200524021416.17049-4-jonathan@marek.ca \
--to=jonathan@marek.ca \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.