From: Satya Tangirala <satyat@google.com>
To: linux-scsi@vger.kernel.org
Cc: Satya Tangirala <satyat@google.com>, Eric Biggers <ebiggers@google.com>
Subject: [PATCH 1/3] scsi: ufs: UFS driver v2.1 spec crypto additions
Date: Wed, 17 Jun 2020 08:18:39 +0000 [thread overview]
Message-ID: <20200617081841.218985-2-satyat@google.com> (raw)
In-Reply-To: <20200617081841.218985-1-satyat@google.com>
Add the crypto registers and structs defined in v2.1 of the JEDEC UFSHCI
specification in preparation to add support for inline encryption to
UFS.
Signed-off-by: Satya Tangirala <satyat@google.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
---
drivers/scsi/ufs/ufshcd.c | 2 ++
drivers/scsi/ufs/ufshcd.h | 6 ++++
drivers/scsi/ufs/ufshci.h | 67 +++++++++++++++++++++++++++++++++++++--
3 files changed, 73 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index ad4fc829cbb2..777090a0a080 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4792,6 +4792,8 @@ ufshcd_transfer_rsp_status(struct ufs_hba *hba, struct ufshcd_lrb *lrbp)
case OCS_MISMATCH_RESP_UPIU_SIZE:
case OCS_PEER_COMM_FAILURE:
case OCS_FATAL_ERROR:
+ case OCS_INVALID_CRYPTO_CONFIG:
+ case OCS_GENERAL_CRYPTO_ERROR:
default:
result |= DID_ERROR << 16;
dev_err(hba->dev,
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index bf97d616e597..b4981f1c37a2 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -564,6 +564,12 @@ enum ufshcd_caps {
* provisioned to be used. This would increase the write performance.
*/
UFSHCD_CAP_WB_EN = 1 << 7,
+
+ /*
+ * This capability allows the host controller driver to use the
+ * inline crypto engine, if it is present
+ */
+ UFSHCD_CAP_CRYPTO = 1 << 8,
};
struct ufs_hba_variant_params {
diff --git a/drivers/scsi/ufs/ufshci.h b/drivers/scsi/ufs/ufshci.h
index c2961d37cc1c..c0651fe6dbbc 100644
--- a/drivers/scsi/ufs/ufshci.h
+++ b/drivers/scsi/ufs/ufshci.h
@@ -90,6 +90,7 @@ enum {
MASK_64_ADDRESSING_SUPPORT = 0x01000000,
MASK_OUT_OF_ORDER_DATA_DELIVERY_SUPPORT = 0x02000000,
MASK_UIC_DME_TEST_MODE_SUPPORT = 0x04000000,
+ MASK_CRYPTO_SUPPORT = 0x10000000,
};
#define UFS_MASK(mask, offset) ((mask) << (offset))
@@ -143,6 +144,7 @@ enum {
#define DEVICE_FATAL_ERROR 0x800
#define CONTROLLER_FATAL_ERROR 0x10000
#define SYSTEM_BUS_FATAL_ERROR 0x20000
+#define CRYPTO_ENGINE_FATAL_ERROR 0x40000
#define UFSHCD_UIC_HIBERN8_MASK (UIC_HIBERNATE_ENTER |\
UIC_HIBERNATE_EXIT)
@@ -155,11 +157,13 @@ enum {
#define UFSHCD_ERROR_MASK (UIC_ERROR |\
DEVICE_FATAL_ERROR |\
CONTROLLER_FATAL_ERROR |\
- SYSTEM_BUS_FATAL_ERROR)
+ SYSTEM_BUS_FATAL_ERROR |\
+ CRYPTO_ENGINE_FATAL_ERROR)
#define INT_FATAL_ERRORS (DEVICE_FATAL_ERROR |\
CONTROLLER_FATAL_ERROR |\
- SYSTEM_BUS_FATAL_ERROR)
+ SYSTEM_BUS_FATAL_ERROR |\
+ CRYPTO_ENGINE_FATAL_ERROR)
/* HCS - Host Controller Status 30h */
#define DEVICE_PRESENT 0x1
@@ -318,6 +322,61 @@ enum {
INTERRUPT_MASK_ALL_VER_21 = 0x71FFF,
};
+/* CCAP - Crypto Capability 100h */
+union ufs_crypto_capabilities {
+ __le32 reg_val;
+ struct {
+ u8 num_crypto_cap;
+ u8 config_count;
+ u8 reserved;
+ u8 config_array_ptr;
+ };
+};
+
+enum ufs_crypto_key_size {
+ UFS_CRYPTO_KEY_SIZE_INVALID = 0x0,
+ UFS_CRYPTO_KEY_SIZE_128 = 0x1,
+ UFS_CRYPTO_KEY_SIZE_192 = 0x2,
+ UFS_CRYPTO_KEY_SIZE_256 = 0x3,
+ UFS_CRYPTO_KEY_SIZE_512 = 0x4,
+};
+
+enum ufs_crypto_alg {
+ UFS_CRYPTO_ALG_AES_XTS = 0x0,
+ UFS_CRYPTO_ALG_BITLOCKER_AES_CBC = 0x1,
+ UFS_CRYPTO_ALG_AES_ECB = 0x2,
+ UFS_CRYPTO_ALG_ESSIV_AES_CBC = 0x3,
+};
+
+/* x-CRYPTOCAP - Crypto Capability X */
+union ufs_crypto_cap_entry {
+ __le32 reg_val;
+ struct {
+ u8 algorithm_id;
+ u8 sdus_mask; /* Supported data unit size mask */
+ u8 key_size;
+ u8 reserved;
+ };
+};
+
+#define UFS_CRYPTO_CONFIGURATION_ENABLE (1 << 7)
+#define UFS_CRYPTO_KEY_MAX_SIZE 64
+/* x-CRYPTOCFG - Crypto Configuration X */
+union ufs_crypto_cfg_entry {
+ __le32 reg_val[32];
+ struct {
+ u8 crypto_key[UFS_CRYPTO_KEY_MAX_SIZE];
+ u8 data_unit_size;
+ u8 crypto_cap_idx;
+ u8 reserved_1;
+ u8 config_enable;
+ u8 reserved_multi_host;
+ u8 reserved_2;
+ u8 vsb[2];
+ u8 reserved_3[56];
+ };
+};
+
/*
* Request Descriptor Definitions
*/
@@ -339,6 +398,7 @@ enum {
UTP_NATIVE_UFS_COMMAND = 0x10000000,
UTP_DEVICE_MANAGEMENT_FUNCTION = 0x20000000,
UTP_REQ_DESC_INT_CMD = 0x01000000,
+ UTP_REQ_DESC_CRYPTO_ENABLE_CMD = 0x00800000,
};
/* UTP Transfer Request Data Direction (DD) */
@@ -358,6 +418,9 @@ enum {
OCS_PEER_COMM_FAILURE = 0x5,
OCS_ABORTED = 0x6,
OCS_FATAL_ERROR = 0x7,
+ OCS_DEVICE_FATAL_ERROR = 0x8,
+ OCS_INVALID_CRYPTO_CONFIG = 0x9,
+ OCS_GENERAL_CRYPTO_ERROR = 0xA,
OCS_INVALID_COMMAND_STATUS = 0x0F,
MASK_OCS = 0x0F,
};
--
2.27.0.290.gba653c62da-goog
next prev parent reply other threads:[~2020-06-17 8:18 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-17 8:18 [PATCH 0/3] Inline Encryption Support for UFS Satya Tangirala
2020-06-17 8:18 ` Satya Tangirala [this message]
2020-06-17 16:26 ` [PATCH 1/3] scsi: ufs: UFS driver v2.1 spec crypto additions Eric Biggers
2020-06-17 8:18 ` [PATCH 2/3] scsi: ufs: UFS crypto API Satya Tangirala
2020-06-17 16:27 ` Eric Biggers
2020-06-17 8:18 ` [PATCH 3/3] scsi: ufs: Add inline encryption support to UFS Satya Tangirala
2020-06-17 16:28 ` Eric Biggers
2020-06-18 2:52 ` Satya Tangirala
2020-06-17 16:24 ` [PATCH 0/3] Inline Encryption Support for UFS Eric Biggers
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200617081841.218985-2-satyat@google.com \
--to=satyat@google.com \
--cc=ebiggers@google.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.