[PATCH v2 14/18] tools: gpio: rename nlines to num_lines

[Kent Gibson <warthog618@gmail.com>]

Rename nlines to num_lines to be consistent with other usage for fields
describing the number of entries in an array.

Signed-off-by: Kent Gibson <warthog618@gmail.com>
---
 tools/gpio/gpio-utils.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/tools/gpio/gpio-utils.c b/tools/gpio/gpio-utils.c
index 16a5d9cb9da2..d527980bcb94 100644
--- a/tools/gpio/gpio-utils.c
+++ b/tools/gpio/gpio-utils.c
@@ -38,7 +38,7 @@
  *			such as "gpiochip0"
  * @lines:		An array desired lines, specified by offset
  *			index for the associated GPIO device.
- * @nline:		The number of lines to request.
+ * @num_lines:		The number of lines to request.
  * @flag:		The new flag for requsted gpio. Reference
  *			"linux/gpio.h" for the meaning of flag.
  * @data:		Default value will be set to gpio when flag is
@@ -56,7 +56,7 @@
  *			On failure return the errno.
  */
 int gpiotools_request_linehandle(const char *device_name, unsigned int *lines,
-				 unsigned int nlines, unsigned int flag,
+				 unsigned int num_lines, unsigned int flag,
 				 struct gpiohandle_data *data,
 				 const char *consumer_label)
 {
@@ -78,12 +78,12 @@ int gpiotools_request_linehandle(const char *device_name, unsigned int *lines,
 		goto exit_free_name;
 	}
 
-	for (i = 0; i < nlines; i++)
+	for (i = 0; i < num_lines; i++)
 		req.lineoffsets[i] = lines[i];
 
 	req.flags = flag;
 	strcpy(req.consumer_label, consumer_label);
-	req.lines = nlines;
+	req.lines = num_lines;
 	if (flag & GPIOHANDLE_REQUEST_OUTPUT)
 		memcpy(req.default_values, data, sizeof(req.default_values));
 
@@ -194,20 +194,20 @@ int gpiotools_get(const char *device_name, unsigned int line)
  *			such as "gpiochip0".
  * @lines:		An array desired lines, specified by offset
  *			index for the associated GPIO device.
- * @nline:		The number of lines to request.
+ * @num_lines:		The number of lines to request.
  * @data:		The array of values get from gpiochip.
  *
  * Return:		On success return 0;
  *			On failure return the errno.
  */
 int gpiotools_gets(const char *device_name, unsigned int *lines,
-		   unsigned int nlines, struct gpiohandle_data *data)
+		   unsigned int num_lines, struct gpiohandle_data *data)
 {
 	int fd;
 	int ret;
 	int ret_close;
 
-	ret = gpiotools_request_linehandle(device_name, lines, nlines,
+	ret = gpiotools_request_linehandle(device_name, lines, num_lines,
 					   GPIOHANDLE_REQUEST_INPUT, data,
 					   CONSUMER);
 	if (ret < 0)
@@ -245,7 +245,7 @@ int gpiotools_set(const char *device_name, unsigned int line,
  *			such as "gpiochip0".
  * @lines:		An array desired lines, specified by offset
  *			index for the associated GPIO device.
- * @nline:		The number of lines to request.
+ * @num_lines:		The number of lines to request.
  * @data:		The array of values set to gpiochip, must be
  *			0(low) or 1(high).
  *
@@ -253,11 +253,11 @@ int gpiotools_set(const char *device_name, unsigned int line,
  *			On failure return the errno.
  */
 int gpiotools_sets(const char *device_name, unsigned int *lines,
-		   unsigned int nlines, struct gpiohandle_data *data)
+		   unsigned int num_lines, struct gpiohandle_data *data)
 {
 	int ret;
 
-	ret = gpiotools_request_linehandle(device_name, lines, nlines,
+	ret = gpiotools_request_linehandle(device_name, lines, num_lines,
 					   GPIOHANDLE_REQUEST_OUTPUT, data,
 					   CONSUMER);
 	if (ret < 0)
-- 
2.27.0