[PATCH 08/13] dt-bindings: iio: adc: ti,adc12138 yaml conversion.

[Jonathan Cameron <jic23@kernel.org>]

From: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Simple binding conversion.  Only addition was #io-channel-cells to
allow for potential consumers of the channels on this device.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
---
 .../bindings/iio/adc/ti,adc12138.yaml         | 85 +++++++++++++++++++
 .../bindings/iio/adc/ti-adc12138.txt          | 37 --------
 2 files changed, 85 insertions(+), 37 deletions(-)

diff --git a/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml b/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml
new file mode 100644
index 000000000000..3e8c43aa8ef3
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/ti,adc12138.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments ADC12138 and similar self-calibrating ADCs
+
+maintainers:
+  - Akinobu Mita <akinobu.mita@gmail.com>
+
+description: |
+  13 bit ADCs with 1, 2 or 8 inputs and self calibrating circuitry to
+  correct for linearity, zero and full scale errors.
+
+properties:
+  compatible:
+    enum:
+      - ti,adc12130
+      - ti,adc12132
+      - ti,adc12138
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+    description: End of Conversion (EOC) interrupt
+
+  clocks:
+    maxItems: 1
+    description: Conversion clock input.
+
+  spi-max-frequency: true
+
+  vref-p-supply:
+    description: The regulator supply for positive analog voltage reference
+
+  vref-n-suppy:
+    description: |
+      The regulator supply for negative analog voltage reference
+      (Note that this must not go below GND or exceed vref-p)
+      If not specified, this is assumed to be analog ground.
+
+  ti,acquisition-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 6, 10, 18, 34]
+    description: |
+      The number of conversion clock periods for the S/H's acquisition time.
+      For high source impedances, this value can be increased to 18 or 34.
+      For less ADC accuracy and/or slower CCLK frequencies this value may be
+      decreased to 6.  See section 6.0 INPUT SOURCE RESISTANCE in the
+      datasheet for details.
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - vref-p-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        adc@0 {
+            compatible = "ti,adc12138";
+            reg = <0>;
+            interrupts = <28 IRQ_TYPE_EDGE_RISING>;
+            interrupt-parent = <&gpio1>;
+            clocks = <&cclk>;
+            vref-p-supply = <&ldo4_reg>;
+            spi-max-frequency = <5000000>;
+            ti,acquisition-time = <6>;
+            #io-channel-cells = <1>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt
deleted file mode 100644
index 049a1d36f013..000000000000
--- a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-* Texas Instruments' ADC12130/ADC12132/ADC12138
-
-Required properties:
- - compatible: Should be one of
-	* "ti,adc12130"
-	* "ti,adc12132"
-	* "ti,adc12138"
- - reg: SPI chip select number for the device
- - interrupts: Should contain interrupt for EOC (end of conversion)
- - clocks: phandle to conversion clock input
- - spi-max-frequency: Definision as per
-	Documentation/devicetree/bindings/spi/spi-bus.txt
- - vref-p-supply: The regulator supply for positive analog voltage reference
-
-Optional properties:
- - vref-n-supply: The regulator supply for negative analog voltage reference
-	(Note that this must not go below GND or exceed vref-p)
-	If not specified, this is assumed to be analog ground.
- - ti,acquisition-time: The number of conversion clock periods for the S/H's
-	acquisition time.  Should be one of 6, 10, 18, 34.  If not specified,
-	default value of 10 is used.
-	For high source impedances, this value can be increased to 18 or 34.
-	For less ADC accuracy and/or slower CCLK frequencies this value may be
-	decreased to 6.  See section 6.0 INPUT SOURCE RESISTANCE in the
-	datasheet for details.
-
-Example:
-adc@0 {
-	compatible = "ti,adc12138";
-	reg = <0>;
-	interrupts = <28 IRQ_TYPE_EDGE_RISING>;
-	interrupt-parent = <&gpio1>;
-	clocks = <&cclk>;
-	vref-p-supply = <&ldo4_reg>;
-	spi-max-frequency = <5000000>;
-	ti,acquisition-time = <6>;
-};
-- 
2.28.0