[PATCH 1/4] brcmfmac: add change_bss to support AP isolation

[Wright Feng <wright.feng@cypress.com>]

Hostap has a parameter "ap_isolate" which is used to prevent low-level
bridging of frames between associated stations in the BSS.
Regarding driver side, we add cfg80211 ops method change_bss to support
setting AP isolation if firmware has ap_isolate feature.

Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
---
 .../broadcom/brcm80211/brcmfmac/cfg80211.c    | 23 +++++++++++++++++++
 .../broadcom/brcm80211/brcmfmac/feature.c     |  1 +
 .../broadcom/brcm80211/brcmfmac/feature.h     |  3 ++-
 3 files changed, 26 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
index 5d99771c3f64..7ef93cd66b2c 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
@@ -5425,6 +5425,26 @@ static int brcmf_cfg80211_del_pmk(struct wiphy *wiphy, struct net_device *dev,
 	return brcmf_set_pmk(ifp, NULL, 0);
 }
 
+static int
+brcmf_cfg80211_change_bss(struct wiphy *wiphy, struct net_device *dev,
+			  struct bss_parameters *params)
+{
+	struct brcmf_if *ifp;
+	int ret = 0;
+	u32 ap_isolate;
+
+	brcmf_dbg(TRACE, "Enter\n");
+	ifp = netdev_priv(dev);
+	if (params->ap_isolate >= 0) {
+		ap_isolate = (u32)params->ap_isolate;
+		ret = brcmf_fil_iovar_int_set(ifp, "ap_isolate", ap_isolate);
+		if (ret < 0)
+			brcmf_err("ap_isolate iovar failed: ret=%d\n", ret);
+	}
+
+	return ret;
+}
+
 static struct cfg80211_ops brcmf_cfg80211_ops = {
 	.add_virtual_intf = brcmf_cfg80211_add_iface,
 	.del_virtual_intf = brcmf_cfg80211_del_iface,
@@ -7492,6 +7512,9 @@ struct brcmf_cfg80211_info *brcmf_cfg80211_attach(struct brcmf_pub *drvr,
 	if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_WOWL_GTK))
 		ops->set_rekey_data = brcmf_cfg80211_set_rekey_data;
 #endif
+	if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_AP_ISOLATE))
+		ops->change_bss = brcmf_cfg80211_change_bss;
+
 	err = wiphy_register(wiphy);
 	if (err < 0) {
 		bphy_err(drvr, "Could not register wiphy device (%d)\n", err);
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c
index 0dcefbd0c000..1ffa9742612d 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c
@@ -278,6 +278,7 @@ void brcmf_feat_attach(struct brcmf_pub *drvr)
 	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_RSDB, "rsdb_mode");
 	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_TDLS, "tdls_enable");
 	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_MFP, "mfp");
+	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_AP_ISOLATE, "ap_isolate");
 
 	pfn_mac.version = BRCMF_PFN_MACADDR_CFG_VER;
 	err = brcmf_fil_iovar_data_get(ifp, "pfn_macaddr", &pfn_mac,
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h
index cda3fc1bab7f..243d9afddb8c 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h
@@ -49,7 +49,8 @@
 	BRCMF_FEAT_DEF(MONITOR_FMT_RADIOTAP) \
 	BRCMF_FEAT_DEF(MONITOR_FMT_HW_RX_HDR) \
 	BRCMF_FEAT_DEF(DOT11H) \
-	BRCMF_FEAT_DEF(SAE)
+	BRCMF_FEAT_DEF(SAE) \
+	BRCMF_FEAT_DEF(AP_ISOLATE)
 
 /*
  * Quirks:
-- 
2.25.0