All of lore.kernel.org
 help / color / mirror / Atom feed
From: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: Vladimir Oltean <olteanv@gmail.com>
Cc: davem@davemloft.net, netdev@vger.kernel.org, yangbo.lu@nxp.com,
	xiaoliang.yang_1@nxp.com, UNGLinuxDriver@microchip.com,
	claudiu.manoil@nxp.com, andrew@lunn.ch, vivien.didelot@gmail.com,
	f.fainelli@gmail.com, kuba@kernel.org
Subject: Re: [PATCH v2 net 2/8] net: mscc: ocelot: add locking for the port TX timestamp ID
Date: Fri, 18 Sep 2020 17:27:25 +0200	[thread overview]
Message-ID: <20200918152725.GY9675@piout.net> (raw)
In-Reply-To: <20200918010730.2911234-3-olteanv@gmail.com>

On 18/09/2020 04:07:24+0300, Vladimir Oltean wrote:
> From: Vladimir Oltean <vladimir.oltean@nxp.com>
> 
> The ocelot_port->ts_id is used to:
> (a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
>     with an skb.
> (b) populate the REW_OP from the injection header of the ongoing skb.
> Only then is ocelot_port->ts_id incremented.
> 
> This is a problem because, at least theoretically, another timestampable
> skb might use the same ocelot_port->ts_id before that is incremented.
> Normally all transmit calls are serialized by the netdev transmit
> spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
> called by DSA, which has started declaring the NETIF_F_LLTX feature
> since commit 2b86cb829976 ("net: dsa: declare lockless TX feature for
> slave ports").  So the logic of using and incrementing the timestamp id
> should be atomic per port.
> 
> The solution is to use the global ocelot_port->ts_id only while
> protected by the associated ocelot_port->ts_id_lock. That's where we
> populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
> is called for the actual skb, but for felix, it is called for the skb's
> clone. That is something which will also be changed in the future.
> 
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>

Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

> ---
> Changes in v2:
> Added an extra explanation about NETIF_F_LLTX in commit message.
> 
>  drivers/net/ethernet/mscc/ocelot.c     |  8 +++++++-
>  drivers/net/ethernet/mscc/ocelot_net.c |  6 ++----
>  include/soc/mscc/ocelot.h              |  1 +
>  net/dsa/tag_ocelot.c                   | 11 +++++++----
>  4 files changed, 17 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/net/ethernet/mscc/ocelot.c b/drivers/net/ethernet/mscc/ocelot.c
> index 5abb7d2b0a9e..83eb7c325061 100644
> --- a/drivers/net/ethernet/mscc/ocelot.c
> +++ b/drivers/net/ethernet/mscc/ocelot.c
> @@ -421,10 +421,15 @@ int ocelot_port_add_txtstamp_skb(struct ocelot_port *ocelot_port,
>  
>  	if (ocelot->ptp && shinfo->tx_flags & SKBTX_HW_TSTAMP &&
>  	    ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> +		spin_lock(&ocelot_port->ts_id_lock);
> +
>  		shinfo->tx_flags |= SKBTX_IN_PROGRESS;
>  		/* Store timestamp ID in cb[0] of sk_buff */
> -		skb->cb[0] = ocelot_port->ts_id % 4;
> +		skb->cb[0] = ocelot_port->ts_id;
> +		ocelot_port->ts_id = (ocelot_port->ts_id + 1) % 4;
>  		skb_queue_tail(&ocelot_port->tx_skbs, skb);
> +
> +		spin_unlock(&ocelot_port->ts_id_lock);
>  		return 0;
>  	}
>  	return -ENODATA;
> @@ -1300,6 +1305,7 @@ void ocelot_init_port(struct ocelot *ocelot, int port)
>  	struct ocelot_port *ocelot_port = ocelot->ports[port];
>  
>  	skb_queue_head_init(&ocelot_port->tx_skbs);
> +	spin_lock_init(&ocelot_port->ts_id_lock);
>  
>  	/* Basic L2 initialization */
>  
> diff --git a/drivers/net/ethernet/mscc/ocelot_net.c b/drivers/net/ethernet/mscc/ocelot_net.c
> index cacabc23215a..8490e42e9e2d 100644
> --- a/drivers/net/ethernet/mscc/ocelot_net.c
> +++ b/drivers/net/ethernet/mscc/ocelot_net.c
> @@ -349,10 +349,8 @@ static int ocelot_port_xmit(struct sk_buff *skb, struct net_device *dev)
>  
>  	if (ocelot->ptp && shinfo->tx_flags & SKBTX_HW_TSTAMP) {
>  		info.rew_op = ocelot_port->ptp_cmd;
> -		if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> -			info.rew_op |= (ocelot_port->ts_id  % 4) << 3;
> -			ocelot_port->ts_id++;
> -		}
> +		if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP)
> +			info.rew_op |= skb->cb[0] << 3;
>  	}
>  
>  	ocelot_gen_ifh(ifh, &info);
> diff --git a/include/soc/mscc/ocelot.h b/include/soc/mscc/ocelot.h
> index da369b12005f..4521dd602ddc 100644
> --- a/include/soc/mscc/ocelot.h
> +++ b/include/soc/mscc/ocelot.h
> @@ -566,6 +566,7 @@ struct ocelot_port {
>  	u8				ptp_cmd;
>  	struct sk_buff_head		tx_skbs;
>  	u8				ts_id;
> +	spinlock_t			ts_id_lock;
>  
>  	phy_interface_t			phy_mode;
>  
> diff --git a/net/dsa/tag_ocelot.c b/net/dsa/tag_ocelot.c
> index 42f327c06dca..b4fc05cafaa6 100644
> --- a/net/dsa/tag_ocelot.c
> +++ b/net/dsa/tag_ocelot.c
> @@ -160,11 +160,14 @@ static struct sk_buff *ocelot_xmit(struct sk_buff *skb,
>  	packing(injection, &qos_class, 19,  17, OCELOT_TAG_LEN, PACK, 0);
>  
>  	if (ocelot->ptp && (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) {
> +		struct sk_buff *clone = DSA_SKB_CB(skb)->clone;
> +
>  		rew_op = ocelot_port->ptp_cmd;
> -		if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> -			rew_op |= (ocelot_port->ts_id  % 4) << 3;
> -			ocelot_port->ts_id++;
> -		}
> +		/* Retrieve timestamp ID populated inside skb->cb[0] of the
> +		 * clone by ocelot_port_add_txtstamp_skb
> +		 */
> +		if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP)
> +			rew_op |= clone->cb[0] << 3;
>  
>  		packing(injection, &rew_op, 125, 117, OCELOT_TAG_LEN, PACK, 0);
>  	}
> -- 
> 2.25.1
> 

-- 
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

  parent reply	other threads:[~2020-09-18 16:16 UTC|newest]

Thread overview: 33+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-18  1:07 [PATCH v2 net 0/8] Bugfixes in Microsemi Ocelot switch driver Vladimir Oltean
2020-09-18  1:07 ` [PATCH v2 net 1/8] net: mscc: ocelot: fix race condition with TX timestamping Vladimir Oltean
2020-09-18 15:23   ` Alexandre Belloni
2020-09-18 15:24   ` Alexandre Belloni
2020-09-18 15:24   ` Alexandre Belloni
2020-09-18 15:24   ` Alexandre Belloni
2020-09-18 15:24   ` Alexandre Belloni
2020-09-18 15:25   ` Alexandre Belloni
2020-09-18 15:25   ` Alexandre Belloni
2020-09-18 15:26   ` Alexandre Belloni
2020-09-18 15:27     ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 2/8] net: mscc: ocelot: add locking for the port TX timestamp ID Vladimir Oltean
2020-09-18  2:37   ` Florian Fainelli
2020-09-18 15:27   ` Alexandre Belloni [this message]
2020-09-18  1:07 ` [PATCH v2 net 3/8] net: dsa: seville: fix buffer size of the queue system Vladimir Oltean
2020-09-18  2:37   ` Florian Fainelli
2020-09-18 15:27   ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 4/8] net: mscc: ocelot: check for errors on memory allocation of ports Vladimir Oltean
2020-09-18  2:35   ` Florian Fainelli
2020-09-18 15:27   ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 5/8] net: mscc: ocelot: error checking when calling ocelot_init() Vladimir Oltean
2020-09-18  2:35   ` Florian Fainelli
2020-09-18 15:28   ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 6/8] net: mscc: ocelot: refactor ports parsing code into a dedicated function Vladimir Oltean
2020-09-18  2:34   ` Florian Fainelli
2020-09-18 15:28   ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 7/8] net: mscc: ocelot: unregister net devices on unbind Vladimir Oltean
2020-09-18  2:34   ` Florian Fainelli
2020-09-18 15:28   ` Alexandre Belloni
2020-09-18  1:07 ` [PATCH v2 net 8/8] net: mscc: ocelot: deinitialize only initialized ports Vladimir Oltean
2020-09-18  2:36   ` Florian Fainelli
2020-09-18 15:29   ` Alexandre Belloni
2020-09-18 20:52 ` [PATCH v2 net 0/8] Bugfixes in Microsemi Ocelot switch driver David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200918152725.GY9675@piout.net \
    --to=alexandre.belloni@bootlin.com \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=andrew@lunn.ch \
    --cc=claudiu.manoil@nxp.com \
    --cc=davem@davemloft.net \
    --cc=f.fainelli@gmail.com \
    --cc=kuba@kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=vivien.didelot@gmail.com \
    --cc=xiaoliang.yang_1@nxp.com \
    --cc=yangbo.lu@nxp.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.