From: Andrew Lunn <andrew@lunn.ch>
To: Dan Murphy <dmurphy@ti.com>
Cc: Jakub Kicinski <kuba@kernel.org>,
davem@davemloft.net, f.fainelli@gmail.com, hkallweit1@gmail.com,
robh@kernel.org, devicetree@vger.kernel.org,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH net-next v3 4/4] net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY
Date: Tue, 3 Nov 2020 18:21:53 +0100 [thread overview]
Message-ID: <20201103172153.GO1042051@lunn.ch> (raw)
In-Reply-To: <5b32a56b-f054-5790-c5cf-bf1e86403bad@ti.com>
On Tue, Nov 03, 2020 at 11:09:44AM -0600, Dan Murphy wrote:
> Hello
>
> On 10/30/20 6:03 PM, Jakub Kicinski wrote:
> > On Fri, 30 Oct 2020 12:29:50 -0500 Dan Murphy wrote:
> > > The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
> > > that supports 10M single pair cable.
> > >
> > > The device supports both 2.4-V p2p and 1-V p2p output voltage as defined
> > > by IEEE 802.3cg 10Base-T1L specfications. These modes can be forced via
> > > the device tree or the device is defaulted to auto negotiation to
> > > determine the proper p2p voltage.
> > >
> > > Signed-off-by: Dan Murphy <dmurphy@ti.com>
> > drivers/net/phy/dp83td510.c:70:11: warning: symbol 'dp83td510_feature_array' was not declared. Should it be static?
> I did not see this warning. Did you use W=1?
I _think_ that one is W=1. All the PHY drivers are W=1 clean, and i
want to keep it that way. And i hope to make it the default in a lot
of the network code soon.
> > Also this:
> >
> > WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
> > #429: FILE: drivers/net/phy/dp83td510.c:371:
> > + return -ENOTSUPP;
> >
> > WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
> > #524: FILE: drivers/net/phy/dp83td510.c:466:
> > + return -ENOTSUPP;
> Same with these warnings how where they reproduced?
> >
> > ERROR: space required before the open parenthesis '('
> > #580: FILE: drivers/net/phy/dp83td510.c:522:
> > + if(phydev->autoneg) {
> >
> > ERROR: space required before the open parenthesis '('
> > #588: FILE: drivers/net/phy/dp83td510.c:530:
> > + if(phydev->autoneg) {
> >
These look like checkpatch.
> >
> > And please try to wrap the code on 80 chars on the non trivial lines:
>
> What is the LoC limit for networking just for my clarification and I will
> align with that.
80. I would not be too surprised to see checkpatch getting a patch to
set it to 80 for networking code.
Andrew
next prev parent reply other threads:[~2020-11-03 17:22 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-30 17:29 [PATCH net-next v3 0/4] DP83TD510 Single Pair 10Mbps Ethernet PHY Dan Murphy
2020-10-30 17:29 ` [PATCH net-next v3 1/4] ethtool: Add 10base-T1L link mode entries Dan Murphy
2020-10-30 19:43 ` Andrew Lunn
2020-11-05 2:42 ` Florian Fainelli
2020-10-30 17:29 ` [PATCH net-next v3 2/4] dt-bindings: net: Add Rx/Tx output configuration for 10base T1L Dan Murphy
2020-10-30 19:56 ` Andrew Lunn
2020-11-03 16:52 ` Dan Murphy
2020-11-03 17:07 ` Andrew Lunn
2020-11-04 22:08 ` Rob Herring
2020-10-30 17:29 ` [PATCH net-next v3 3/4] dt-bindings: dp83td510: Add binding for DP83TD510 Ethernet PHY Dan Murphy
2020-10-31 9:27 ` Ioana Ciornei
2020-11-02 17:12 ` Rob Herring
2020-10-30 17:29 ` [PATCH net-next v3 4/4] net: phy: dp83td510: Add support for the " Dan Murphy
2020-10-30 20:15 ` Andrew Lunn
2020-11-03 17:07 ` Dan Murphy
2020-11-03 17:18 ` Andrew Lunn
2020-11-03 17:35 ` Dan Murphy
2020-11-05 3:03 ` Florian Fainelli
2020-10-30 23:03 ` Jakub Kicinski
2020-11-03 17:09 ` Dan Murphy
2020-11-03 17:21 ` Andrew Lunn [this message]
2020-11-03 17:23 ` Dan Murphy
2020-11-03 17:38 ` Andrew Lunn
2020-10-31 9:18 ` Ioana Ciornei
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201103172153.GO1042051@lunn.ch \
--to=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=dmurphy@ti.com \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.