From: Marek Behun <marek.behun@nic.cz>
To: u-boot@lists.denx.de
Subject: [PATCH v1 00/23] phy: marvell: Sync Armada 3k/7k/8k SERDES code with Marvell version
Date: Thu, 29 Apr 2021 10:27:14 +0200 [thread overview]
Message-ID: <20210429102714.701c9b16@thinkpad> (raw)
In-Reply-To: <3b1af7f6-ea2f-7269-50e7-fc9f0a00da7a@denx.de>
On Thu, 29 Apr 2021 08:46:36 +0200
Stefan Roese <sr@denx.de> wrote:
> > phy: marvell: add RX training command
>
> Applied to u-boot-marvell/master
>
> Thanks,
> Stefan
Stefan, do you think it would make sense to at least create a special
mechanism for these platform commands? For example via a top-level
command "plat", i.e. instead of
> rx_training params
we would call
> plat rx_training params
The plat command could list all registered platform specific commands...
Marek
next prev parent reply other threads:[~2021-04-29 8:27 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-24 14:06 [PATCH v1 00/23] phy: marvell: Sync Armada 3k/7k/8k SERDES code with Marvell version Stefan Roese
2021-03-24 14:06 ` [PATCH v1 01/23] phy: marvell: add comphy type PHY_TYPE_USB3 Stefan Roese
2021-03-24 14:06 ` [PATCH v1 02/23] phy: marvell: rename comphy related definitions to COMPHY_XX Stefan Roese
2021-03-24 14:42 ` Pali Rohár
2021-03-24 15:04 ` [EXT] " Kostya Porotchkin
2021-03-24 15:39 ` Stefan Roese
2021-03-24 15:47 ` Pali Rohár
2021-03-24 17:41 ` Marek Behun
2021-04-08 8:03 ` Stefan Roese
2021-03-24 14:06 ` [PATCH v1 03/23] phy: marvell: add missing speed during info prints Stefan Roese
2021-03-24 14:06 ` [PATCH v1 04/23] phy: marvell: cp110: initialize only enabled UTMI units Stefan Roese
2021-03-24 14:06 ` [PATCH v1 05/23] phy: marvell: cp110: utmi: update analog parameters according to latest ETP Stefan Roese
2021-03-24 14:06 ` [PATCH v1 06/23] phy: marvell: fix several minor bugs in comphy_probe Stefan Roese
2021-03-24 14:06 ` [PATCH v1 07/23] phy: marvell: save comphy_map_data priv structure Stefan Roese
2021-03-24 14:06 ` [PATCH v1 08/23] phy: marvell: add RX training command Stefan Roese
2021-03-24 17:46 ` Marek Behun
2021-04-08 8:46 ` Stefan Roese
2021-03-24 14:06 ` [PATCH v1 09/23] phy: marvell: enable comphy info prints for all devices Stefan Roese
2021-03-24 14:06 ` [PATCH v1 10/23] phy: marvell: cp110: remove unused definitions Stefan Roese
2021-03-24 14:06 ` [PATCH v1 11/23] phy: marvell: cp110: let the firmware configure comphy for RXAUI Stefan Roese
2021-03-24 14:06 ` [PATCH v1 12/23] phy: marvell: cp110: let the firmware configure comphy for USB Stefan Roese
2021-03-24 14:06 ` [PATCH v1 13/23] phy: marvell: cp110: let the firmware perform training for XFI Stefan Roese
2021-03-24 14:06 ` [PATCH v1 14/23] phy: marvell: cp110: remove both phy and pipe selector configuration Stefan Roese
2021-03-24 14:06 ` [PATCH v1 15/23] phy: marvell: cp110: clean up driver after it was moved to atf Stefan Roese
2021-03-24 14:06 ` [PATCH v1 16/23] phy: marvell: pass sgmii id to firmware Stefan Roese
2021-03-24 14:06 ` [PATCH v1 17/23] phy: marvell: fix handling of unconnected comphy Stefan Roese
2021-03-24 14:06 ` [PATCH v1 18/23] phy: marvell: cp110: mark u-boot power-off calls Stefan Roese
2021-03-24 14:06 ` [PATCH v1 19/23] phy: marvell: allow to initialize up to 6 USB ports Stefan Roese
2021-03-24 14:06 ` [PATCH v1 20/23] phy: marvell: fix pll initialization for second utmi port Stefan Roese
2021-03-24 14:06 ` [PATCH v1 21/23] phy: marvell: add support for SFI1 Stefan Roese
2021-03-24 14:06 ` [PATCH v1 22/23] phy: marvell: utmi: update utmi config which fixes usb2.0 instability Stefan Roese
2021-03-24 14:06 ` [PATCH v1 23/23] doc: dt-bindings: add Marvell comphy binding Stefan Roese
2021-04-29 6:46 ` [PATCH v1 00/23] phy: marvell: Sync Armada 3k/7k/8k SERDES code with Marvell version Stefan Roese
2021-04-29 8:27 ` Marek Behun [this message]
2021-04-29 9:00 ` Stefan Roese
2021-05-04 22:28 ` Pali Rohár
2021-05-05 7:00 ` Stefan Roese
2021-05-05 9:19 ` Pali Rohár
2021-05-05 16:38 ` Marek Behun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210429102714.701c9b16@thinkpad \
--to=marek.behun@nic.cz \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.