Re: [PATCH v2] net: phy: add Maxlinear GPY115/21x/24x driver

["Russell King (Oracle)" <linux@armlinux.org.uk>]

Hi,

On Thu, Jun 03, 2021 at 03:34:38PM +0800, Xu Liang wrote:
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index bcda7ed2455d..70efab3659ee 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -70,6 +70,7 @@ obj-$(CONFIG_MICREL_PHY)	+= micrel.o
>  obj-$(CONFIG_MICROCHIP_PHY)	+= microchip.o
>  obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
>  obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
> +obj-$(CONFIG_MXL_GPHY)          += mxl-gpy.o

This should use tab(s) to align indentation rather than spaces.

> +static int gpy_config_init(struct phy_device *phydev)
> +{
> +	int ret, fw_ver;
> +
> +	/* Show GPY PHY FW version in dmesg */
> +	fw_ver = phy_read(phydev, PHY_FWV);
> +	if (fw_ver < 0)
> +		return fw_ver;
> +
> +	phydev_info(phydev, "Firmware Version: 0x%04X (%s)\n", fw_ver,
> +		    (fw_ver & PHY_FWV_REL_MASK) ? "release" : "test");

Does this need to print the firmware version each time config_init()
is called? Is it likely to change beyond? Would it be more sensible
to print it in the probe() method?

> +static int gpy_config_aneg(struct phy_device *phydev)
> +{
> +	bool changed = false;
> +	u32 adv;
> +	int ret;
> +
> +	if (phydev->autoneg == AUTONEG_DISABLE) {
> +		return phydev->duplex != DUPLEX_FULL
> +			? genphy_setup_forced(phydev)
> +			: genphy_c45_pma_setup_forced(phydev);

I think this needs a comment to describe what is going on here to
explain why the duplex setting influences whether we program the PHY
via C22 or C45.

> +static void gpy_update_interface(struct phy_device *phydev)
> +{
> +	int ret;
> +
> +	/* Interface mode is fixed for USXGMII and integrated PHY */
> +	if (phydev->interface == PHY_INTERFACE_MODE_USXGMII ||
> +	    phydev->interface == PHY_INTERFACE_MODE_INTERNAL)
> +		return;
> +
> +	/* Automatically switch SERDES interface between SGMII and 2500-BaseX
> +	 * according to speed. Disable ANEG in 2500-BaseX mode.
> +	 */
> +	switch (phydev->speed) {
> +	case SPEED_2500:
> +		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
> +		ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
> +					     VSPEC1_SGMII_CTRL,
> +					     VSPEC1_SGMII_CTRL_ANEN, 0);

Do you need to know if the bit was changed? It doesn't appear so, so
please consider using phy_modify_mmd() here and in the other part of
this switch block.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!