From: Tero Kristo <kristo@kernel.org>
To: lokeshvutla@ti.com, trini@konsulko.com, u-boot@lists.denx.de
Subject: [PATCHv6 26/26] arm: dts: k3-j72xx: correct MCU timer1 frequency
Date: Fri, 11 Jun 2021 11:45:27 +0300 [thread overview]
Message-ID: <20210611084527.7048-27-kristo@kernel.org> (raw)
In-Reply-To: <20210611084527.7048-1-kristo@kernel.org>
MCU timer1 is used as the tick timer for MCU R5 SPL, and the
clock-frequency defined in DT appears to be incorrect at the moment.
Actual clock source for the timer is MCU_SYSCLK0 / 4 which is 250MHz.
Earlier setup of 25MHz went unnoticed, as there was a separate issue
with omap-timer, which caused an error to the clock by a factor of 8
with j7 devices. This problem surfaced once the omap-timer was fixed.
Signed-off-by: Tero Kristo <kristo@kernel.org>
---
arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi | 2 +-
arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi b/arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi
index bd037be350..c3aae65b39 100644
--- a/arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi
+++ b/arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi
@@ -33,7 +33,7 @@
compatible = "ti,omap5430-timer";
reg = <0x0 0x40400000 0x0 0x80>;
ti,timer-alwon;
- clock-frequency = <25000000>;
+ clock-frequency = <250000000>;
u-boot,dm-spl;
};
diff --git a/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi b/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi
index fe095a6153..951331831e 100644
--- a/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi
+++ b/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi
@@ -46,7 +46,7 @@
compatible = "ti,omap5430-timer";
reg = <0x0 0x40400000 0x0 0x80>;
ti,timer-alwon;
- clock-frequency = <25000000>;
+ clock-frequency = <250000000>;
u-boot,dm-spl;
};
--
2.17.1
next prev parent reply other threads:[~2021-06-11 8:50 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-11 8:45 [PATCHv6 00/26] HSM rearch series for TI K3 devices Tero Kristo
2021-06-11 8:45 ` [PATCHv6 01/26] lib: rational: copy the rational fraction lib routines from Linux Tero Kristo
2021-06-11 8:45 ` [PATCHv6 02/26] arm: mach-k3: introduce new config option for sysfw split Tero Kristo
2021-06-11 8:45 ` [PATCHv6 03/26] remoteproc: k3-r5: remove sysfw PM calls if not supported Tero Kristo
2021-06-11 8:45 ` [PATCHv6 04/26] common: fit: Update board_fit_image_post_process() to pass fit and node_offset Tero Kristo
2021-06-11 8:45 ` [PATCHv6 05/26] clk: fixed_rate: add API for directly registering fixed rate clocks Tero Kristo
2021-06-11 8:45 ` [PATCHv6 06/26] clk: fix clock tree dump to properly dump out every registered clock Tero Kristo
2021-06-11 8:45 ` [PATCHv6 07/26] clk: do not attempt to fetch clock pointer with null device Tero Kristo
2021-06-11 8:45 ` [PATCHv6 08/26] clk: add support for setting clk rate from cmdline Tero Kristo
2021-06-11 8:45 ` [PATCHv6 09/26] clk: sci-clk: fix return value of set_rate Tero Kristo
2021-06-11 8:45 ` [PATCHv6 10/26] clk: fix assigned-clocks to pass with deferring provider Tero Kristo
2021-06-11 8:45 ` [PATCHv6 11/26] clk: fix set_rate to clean up cached rates for the hierarchy Tero Kristo
2021-06-11 8:45 ` [PATCHv6 12/26] clk: add support for TI K3 SoC PLL Tero Kristo
2021-06-11 8:45 ` [PATCHv6 13/26] clk: add support for TI K3 SoC clocks Tero Kristo
2021-06-11 8:45 ` [PATCHv6 14/26] power: domain: Introduce driver for raw TI K3 PDs Tero Kristo
2021-06-11 8:45 ` [PATCHv6 15/26] cmd: ti: pd: Add debug command for K3 power domains Tero Kristo
2021-06-11 8:45 ` [PATCHv6 16/26] tools: k3_fit_atf: add DM binary to the FIT image Tero Kristo
2021-06-11 8:45 ` [PATCHv6 17/26] arm: mach-k3: Add platform data for j721e and j7200 Tero Kristo
2021-06-11 8:45 ` [PATCHv6 18/26] arm: mach-k3: add support for detecting firmware images from FIT Tero Kristo
2021-06-11 8:45 ` [PATCHv6 19/26] arm: mach-k3: do board config for PM only if supported Tero Kristo
2021-06-11 8:45 ` [PATCHv6 20/26] arm: mach-k3: common: Drop main r5 start Tero Kristo
2021-06-11 8:45 ` [PATCHv6 21/26] arm: mach-k3: sysfw-loader: pass boardcfg to sciserver Tero Kristo
2021-06-11 8:45 ` [PATCHv6 22/26] arm: mach-k3: j721e_init: Force early probe of clk-k3 driver Tero Kristo
2021-06-11 8:45 ` [PATCHv6 23/26] configs: j721e_evm_r5: Enable raw access power management features Tero Kristo
2021-06-11 8:45 ` [PATCHv6 24/26] configs: j7200_evm_r5: " Tero Kristo
2021-06-11 8:45 ` [PATCHv6 25/26] board: ti: j72xx: README: update build instructions and image formats Tero Kristo
2021-06-11 8:45 ` Tero Kristo [this message]
2021-06-11 11:08 ` [PATCHv6 00/26] HSM rearch series for TI K3 devices Lokesh Vutla
2021-06-11 11:18 ` Tero Kristo
2021-06-11 13:43 ` Lokesh Vutla
2021-06-11 14:13 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210611084527.7048-27-kristo@kernel.org \
--to=kristo@kernel.org \
--cc=lokeshvutla@ti.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.