[PATCH AUTOSEL 4.4 5/6] net: tulip: de4x5: fix the problem that the array 'lp->phy[8]' may be out of bound

[Sasha Levin <sashal@kernel.org>]

From: zhangyue <zhangyue1@kylinos.cn>

[ Upstream commit 61217be886b5f7402843677e4be7e7e83de9cb41 ]

In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.

At this time, the array 'lp->phy[8]' may be out of bound.

Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/dec/tulip/de4x5.c | 30 +++++++++++++++-----------
 1 file changed, 17 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/dec/tulip/de4x5.c b/drivers/net/ethernet/dec/tulip/de4x5.c
index 7799cf33cc6e2..7c4150a83a082 100644
--- a/drivers/net/ethernet/dec/tulip/de4x5.c
+++ b/drivers/net/ethernet/dec/tulip/de4x5.c
@@ -4992,19 +4992,23 @@ mii_get_phy(struct net_device *dev)
 	}
 	if ((j == limit) && (i < DE4X5_MAX_MII)) {
 	    for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
-	    lp->phy[k].addr = i;
-	    lp->phy[k].id = id;
-	    lp->phy[k].spd.reg = GENERIC_REG;      /* ANLPA register         */
-	    lp->phy[k].spd.mask = GENERIC_MASK;    /* 100Mb/s technologies   */
-	    lp->phy[k].spd.value = GENERIC_VALUE;  /* TX & T4, H/F Duplex    */
-	    lp->mii_cnt++;
-	    lp->active++;
-	    printk("%s: Using generic MII device control. If the board doesn't operate,\nplease mail the following dump to the author:\n", dev->name);
-	    j = de4x5_debug;
-	    de4x5_debug |= DEBUG_MII;
-	    de4x5_dbg_mii(dev, k);
-	    de4x5_debug = j;
-	    printk("\n");
+	    if (k < DE4X5_MAX_PHY) {
+		lp->phy[k].addr = i;
+		lp->phy[k].id = id;
+		lp->phy[k].spd.reg = GENERIC_REG;      /* ANLPA register         */
+		lp->phy[k].spd.mask = GENERIC_MASK;    /* 100Mb/s technologies   */
+		lp->phy[k].spd.value = GENERIC_VALUE;  /* TX & T4, H/F Duplex    */
+		lp->mii_cnt++;
+		lp->active++;
+		printk("%s: Using generic MII device control. If the board doesn't operate,\nplease mail the following dump to the author:\n", dev->name);
+		j = de4x5_debug;
+		de4x5_debug |= DEBUG_MII;
+		de4x5_dbg_mii(dev, k);
+		de4x5_debug = j;
+		printk("\n");
+	    } else {
+		goto purgatory;
+	    }
 	}
     }
   purgatory:
-- 
2.33.0