[PATCH net-next 07/15] net/mlx5: Update log_max_qp value to FW max capability

[Saeed Mahameed <saeed@kernel.org>]

From: Maher Sanalla <msanalla@nvidia.com>

log_max_qp in driver's default profile #2 was set to 18, but FW actually
supports 17 at the most - a situation that led to the concerning print
when the driver is loaded:
"log_max_qp value in current profile is 18, changing to HCA capabaility
limit (17)"

The expected behavior from mlx5_profile #2 is to match the maximum FW
capability in regards to log_max_qp. Thus, log_max_qp in profile #2 is
initialized to a defined static value (0xff) - which basically means that
when loading this profile, log_max_qp value  will be what the currently
installed FW supports at most.

Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
---
 drivers/net/ethernet/mellanox/mlx5/core/main.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/main.c b/drivers/net/ethernet/mellanox/mlx5/core/main.c
index 6b225bb5751a..2c774f367199 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c
@@ -98,6 +98,8 @@ enum {
 	MLX5_ATOMIC_REQ_MODE_HOST_ENDIANNESS = 0x1,
 };
 
+#define LOG_MAX_SUPPORTED_QPS 0xff
+
 static struct mlx5_profile profile[] = {
 	[0] = {
 		.mask           = 0,
@@ -109,7 +111,7 @@ static struct mlx5_profile profile[] = {
 	[2] = {
 		.mask		= MLX5_PROF_MASK_QP_SIZE |
 				  MLX5_PROF_MASK_MR_CACHE,
-		.log_max_qp	= 18,
+		.log_max_qp	= LOG_MAX_SUPPORTED_QPS,
 		.mr_cache[0]	= {
 			.size	= 500,
 			.limit	= 250
@@ -523,7 +525,9 @@ static int handle_hca_cap(struct mlx5_core_dev *dev, void *set_ctx)
 		 to_fw_pkey_sz(dev, 128));
 
 	/* Check log_max_qp from HCA caps to set in current profile */
-	if (MLX5_CAP_GEN_MAX(dev, log_max_qp) < prof->log_max_qp) {
+	if (prof->log_max_qp == LOG_MAX_SUPPORTED_QPS) {
+		prof->log_max_qp = MLX5_CAP_GEN_MAX(dev, log_max_qp);
+	} else if (MLX5_CAP_GEN_MAX(dev, log_max_qp) < prof->log_max_qp) {
 		mlx5_core_warn(dev, "log_max_qp value in current profile is %d, changing it to HCA capability limit (%d)\n",
 			       prof->log_max_qp,
 			       MLX5_CAP_GEN_MAX(dev, log_max_qp));
-- 
2.33.1