From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Yang Xu <xuyang2018.jy@fujitsu.com>,
Shuah Khan <skhan@linuxfoundation.org>,
Sasha Levin <sashal@kernel.org>,
shuah@kernel.org, linux-kselftest@vger.kernel.org
Subject: [PATCH AUTOSEL 5.10 08/27] selftests/zram: Adapt the situation that /dev/zram0 is being used
Date: Wed, 9 Feb 2022 13:40:44 -0500 [thread overview]
Message-ID: <20220209184103.47635-8-sashal@kernel.org> (raw)
In-Reply-To: <20220209184103.47635-1-sashal@kernel.org>
From: Yang Xu <xuyang2018.jy@fujitsu.com>
[ Upstream commit 01dabed20573804750af5c7bf8d1598a6bf7bf6e ]
If zram-generator package is installed and works, then we can not remove
zram module because zram swap is being used. This case needs a clean zram
environment, change this test by using hot_add/hot_remove interface. So
even zram device is being used, we still can add zram device and remove
them in cleanup.
The two interface was introduced since kernel commit 6566d1a32bf7("zram:
add dynamic device add/remove functionality") in v4.2-rc1. If kernel
supports these two interface, we use hot_add/hot_remove to slove this
problem, if not, just check whether zram is being used or built in, then
skip it on old kernel.
Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
tools/testing/selftests/zram/zram.sh | 15 +---
tools/testing/selftests/zram/zram01.sh | 3 +-
tools/testing/selftests/zram/zram02.sh | 1 -
tools/testing/selftests/zram/zram_lib.sh | 110 +++++++++++++----------
4 files changed, 66 insertions(+), 63 deletions(-)
diff --git a/tools/testing/selftests/zram/zram.sh b/tools/testing/selftests/zram/zram.sh
index 232e958ec4547..b0b91d9b0dc21 100755
--- a/tools/testing/selftests/zram/zram.sh
+++ b/tools/testing/selftests/zram/zram.sh
@@ -2,9 +2,6 @@
# SPDX-License-Identifier: GPL-2.0
TCID="zram.sh"
-# Kselftest framework requirement - SKIP code is 4.
-ksft_skip=4
-
. ./zram_lib.sh
run_zram () {
@@ -18,14 +15,4 @@ echo ""
check_prereqs
-# check zram module exists
-MODULE_PATH=/lib/modules/`uname -r`/kernel/drivers/block/zram/zram.ko
-if [ -f $MODULE_PATH ]; then
- run_zram
-elif [ -b /dev/zram0 ]; then
- run_zram
-else
- echo "$TCID : No zram.ko module or /dev/zram0 device file not found"
- echo "$TCID : CONFIG_ZRAM is not set"
- exit $ksft_skip
-fi
+run_zram
diff --git a/tools/testing/selftests/zram/zram01.sh b/tools/testing/selftests/zram/zram01.sh
index e9e9eb777e2c7..8f4affe34f3e4 100755
--- a/tools/testing/selftests/zram/zram01.sh
+++ b/tools/testing/selftests/zram/zram01.sh
@@ -33,7 +33,7 @@ zram_algs="lzo"
zram_fill_fs()
{
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
echo "fill zram$i..."
local b=0
while [ true ]; do
@@ -67,7 +67,6 @@ zram_mount
zram_fill_fs
zram_cleanup
-zram_unload
if [ $ERR_CODE -ne 0 ]; then
echo "$TCID : [FAIL]"
diff --git a/tools/testing/selftests/zram/zram02.sh b/tools/testing/selftests/zram/zram02.sh
index e83b404807c09..2418b0c4ed136 100755
--- a/tools/testing/selftests/zram/zram02.sh
+++ b/tools/testing/selftests/zram/zram02.sh
@@ -36,7 +36,6 @@ zram_set_memlimit
zram_makeswap
zram_swapoff
zram_cleanup
-zram_unload
if [ $ERR_CODE -ne 0 ]; then
echo "$TCID : [FAIL]"
diff --git a/tools/testing/selftests/zram/zram_lib.sh b/tools/testing/selftests/zram/zram_lib.sh
index f47fc0f27e99e..21ec1966de76c 100755
--- a/tools/testing/selftests/zram/zram_lib.sh
+++ b/tools/testing/selftests/zram/zram_lib.sh
@@ -5,10 +5,12 @@
# Author: Alexey Kodanev <alexey.kodanev@oracle.com>
# Modified: Naresh Kamboju <naresh.kamboju@linaro.org>
-MODULE=0
dev_makeswap=-1
dev_mounted=-1
-
+dev_start=0
+dev_end=-1
+module_load=-1
+sys_control=-1
# Kselftest framework requirement - SKIP code is 4.
ksft_skip=4
kernel_version=`uname -r | cut -d'.' -f1,2`
@@ -46,57 +48,72 @@ zram_cleanup()
{
echo "zram cleanup"
local i=
- for i in $(seq 0 $dev_makeswap); do
+ for i in $(seq $dev_start $dev_makeswap); do
swapoff /dev/zram$i
done
- for i in $(seq 0 $dev_mounted); do
+ for i in $(seq $dev_start $dev_mounted); do
umount /dev/zram$i
done
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
echo 1 > /sys/block/zram${i}/reset
rm -rf zram$i
done
-}
+ if [ $sys_control -eq 1 ]; then
+ for i in $(seq $dev_start $dev_end); do
+ echo $i > /sys/class/zram-control/hot_remove
+ done
+ fi
-zram_unload()
-{
- if [ $MODULE -ne 0 ] ; then
- echo "zram rmmod zram"
+ if [ $module_load -eq 1 ]; then
rmmod zram > /dev/null 2>&1
fi
}
zram_load()
{
- # check zram module exists
- MODULE_PATH=/lib/modules/`uname -r`/kernel/drivers/block/zram/zram.ko
- if [ -f $MODULE_PATH ]; then
- MODULE=1
- echo "create '$dev_num' zram device(s)"
- modprobe zram num_devices=$dev_num
- if [ $? -ne 0 ]; then
- echo "failed to insert zram module"
- exit 1
- fi
-
- dev_num_created=$(ls /dev/zram* | wc -w)
+ echo "create '$dev_num' zram device(s)"
+
+ # zram module loaded, new kernel
+ if [ -d "/sys/class/zram-control" ]; then
+ echo "zram modules already loaded, kernel supports" \
+ "zram-control interface"
+ dev_start=$(ls /dev/zram* | wc -w)
+ dev_end=$(($dev_start + $dev_num - 1))
+ sys_control=1
+
+ for i in $(seq $dev_start $dev_end); do
+ cat /sys/class/zram-control/hot_add > /dev/null
+ done
+
+ echo "all zram devices (/dev/zram$dev_start~$dev_end" \
+ "successfully created"
+ return 0
+ fi
- if [ "$dev_num_created" -ne "$dev_num" ]; then
- echo "unexpected num of devices: $dev_num_created"
- ERR_CODE=-1
+ # detect old kernel or built-in
+ modprobe zram num_devices=$dev_num
+ if [ ! -d "/sys/class/zram-control" ]; then
+ if grep -q '^zram' /proc/modules; then
+ rmmod zram > /dev/null 2>&1
+ if [ $? -ne 0 ]; then
+ echo "zram module is being used on old kernel" \
+ "without zram-control interface"
+ exit $ksft_skip
+ fi
else
- echo "zram load module successful"
+ echo "test needs CONFIG_ZRAM=m on old kernel without" \
+ "zram-control interface"
+ exit $ksft_skip
fi
- elif [ -b /dev/zram0 ]; then
- echo "/dev/zram0 device file found: OK"
- else
- echo "ERROR: No zram.ko module or no /dev/zram0 device found"
- echo "$TCID : CONFIG_ZRAM is not set"
- exit 1
+ modprobe zram num_devices=$dev_num
fi
+
+ module_load=1
+ dev_end=$(($dev_num - 1))
+ echo "all zram devices (/dev/zram0~$dev_end) successfully created"
}
zram_max_streams()
@@ -110,7 +127,7 @@ zram_max_streams()
return 0
fi
- local i=0
+ local i=$dev_start
for max_s in $zram_max_streams; do
local sys_path="/sys/block/zram${i}/max_comp_streams"
echo $max_s > $sys_path || \
@@ -122,7 +139,7 @@ zram_max_streams()
echo "FAIL can't set max_streams '$max_s', get $max_stream"
i=$(($i + 1))
- echo "$sys_path = '$max_streams' ($i/$dev_num)"
+ echo "$sys_path = '$max_streams'"
done
echo "zram max streams: OK"
@@ -132,15 +149,16 @@ zram_compress_alg()
{
echo "test that we can set compression algorithm"
- local algs=$(cat /sys/block/zram0/comp_algorithm)
+ local i=$dev_start
+ local algs=$(cat /sys/block/zram${i}/comp_algorithm)
echo "supported algs: $algs"
- local i=0
+
for alg in $zram_algs; do
local sys_path="/sys/block/zram${i}/comp_algorithm"
echo "$alg" > $sys_path || \
echo "FAIL can't set '$alg' to $sys_path"
i=$(($i + 1))
- echo "$sys_path = '$alg' ($i/$dev_num)"
+ echo "$sys_path = '$alg'"
done
echo "zram set compression algorithm: OK"
@@ -149,14 +167,14 @@ zram_compress_alg()
zram_set_disksizes()
{
echo "set disk size to zram device(s)"
- local i=0
+ local i=$dev_start
for ds in $zram_sizes; do
local sys_path="/sys/block/zram${i}/disksize"
echo "$ds" > $sys_path || \
echo "FAIL can't set '$ds' to $sys_path"
i=$(($i + 1))
- echo "$sys_path = '$ds' ($i/$dev_num)"
+ echo "$sys_path = '$ds'"
done
echo "zram set disksizes: OK"
@@ -166,14 +184,14 @@ zram_set_memlimit()
{
echo "set memory limit to zram device(s)"
- local i=0
+ local i=$dev_start
for ds in $zram_mem_limits; do
local sys_path="/sys/block/zram${i}/mem_limit"
echo "$ds" > $sys_path || \
echo "FAIL can't set '$ds' to $sys_path"
i=$(($i + 1))
- echo "$sys_path = '$ds' ($i/$dev_num)"
+ echo "$sys_path = '$ds'"
done
echo "zram set memory limit: OK"
@@ -182,8 +200,8 @@ zram_set_memlimit()
zram_makeswap()
{
echo "make swap with zram device(s)"
- local i=0
- for i in $(seq 0 $(($dev_num - 1))); do
+ local i=$dev_start
+ for i in $(seq $dev_start $dev_end); do
mkswap /dev/zram$i > err.log 2>&1
if [ $? -ne 0 ]; then
cat err.log
@@ -206,7 +224,7 @@ zram_makeswap()
zram_swapoff()
{
local i=
- for i in $(seq 0 $dev_makeswap); do
+ for i in $(seq $dev_start $dev_end); do
swapoff /dev/zram$i > err.log 2>&1
if [ $? -ne 0 ]; then
cat err.log
@@ -220,7 +238,7 @@ zram_swapoff()
zram_makefs()
{
- local i=0
+ local i=$dev_start
for fs in $zram_filesystems; do
# if requested fs not supported default it to ext2
which mkfs.$fs > /dev/null 2>&1 || fs=ext2
@@ -239,7 +257,7 @@ zram_makefs()
zram_mount()
{
local i=0
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
echo "mount /dev/zram$i"
mkdir zram$i
mount /dev/zram$i zram$i > /dev/null || \
--
2.34.1
next prev parent reply other threads:[~2022-02-09 18:43 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-02-09 18:40 [PATCH AUTOSEL 5.10 01/27] platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1 Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 02/27] platform/x86: ISST: Fix possible circular locking dependency detected Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 03/27] selftests: rtc: Increase test timeout so that all tests run Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 04/27] kselftest: signal all child processes Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 05/27] net: ieee802154: at86rf230: Stop leaking skb's Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 06/27] selftests/zram: Skip max_comp_streams interface on newer kernel Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 07/27] selftests/zram01.sh: Fix compression ratio calculation Sasha Levin
2022-02-09 18:40 ` Sasha Levin [this message]
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 09/27] selftests: openat2: Print also errno in failure messages Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 10/27] selftests: openat2: Add missing dependency in Makefile Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 11/27] selftests: openat2: Skip testcases that fail with EOPNOTSUPP Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 12/27] selftests: skip mincore.check_file_mmap when fs lacks needed support Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 13/27] ax25: improve the incomplete fix to avoid UAF and NPD bugs Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 14/27] vfs: make freeze_super abort when sync_filesystem returns error Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 15/27] quota: make dquot_quota_sync return errors from ->sync_fs Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 16/27] btrfs: tree-checker: check item_size for dev_item Sasha Levin
2022-02-18 10:36 ` Greg KH
2022-02-18 11:25 ` Su Yue
2022-02-18 13:04 ` Greg KH
2022-02-23 17:20 ` David Sterba
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 17/27] iommu: Fix potential use-after-free during probe Sasha Levin
2022-02-09 18:40 ` Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 18/27] scsi: pm8001: Fix use-after-free for aborted TMF sas_task Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 19/27] scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 20/27] nvme: fix a possible use-after-free in controller reset during load Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 21/27] nvme-tcp: fix possible use-after-free in transport error_recovery work Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 22/27] nvme-rdma: " Sasha Levin
2022-02-09 18:40 ` [PATCH AUTOSEL 5.10 23/27] drm/amdgpu: fix logic inversion in check Sasha Levin
2022-02-09 18:40 ` Sasha Levin
2022-02-09 18:40 ` Sasha Levin
2022-02-09 18:41 ` [PATCH AUTOSEL 5.10 24/27] x86/Xen: streamline (and fix) PV CPU enumeration Sasha Levin
2022-02-09 18:41 ` [PATCH AUTOSEL 5.10 25/27] Revert "module, async: async_synchronize_full() on module init iff async is used" Sasha Levin
2022-02-09 18:41 ` [PATCH AUTOSEL 5.10 26/27] gcc-plugins/stackleak: Use noinstr in favor of notrace Sasha Levin
2022-02-09 18:41 ` [PATCH AUTOSEL 5.10 27/27] random: wake up /dev/random writers after zap Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220209184103.47635-8-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-kselftest@vger.kernel.org \
--cc=shuah@kernel.org \
--cc=skhan@linuxfoundation.org \
--cc=stable@vger.kernel.org \
--cc=xuyang2018.jy@fujitsu.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.