From: Adam Ford <aford173@gmail.com>
To: u-boot@lists.denx.de
Cc: trini@konsulko.com, aford@beaconembedded.com,
Adam Ford <aford173@gmail.com>
Subject: [PATCH 1/2] ARM: dts: logicpd-som-lv: Resync DTS files with Linux 5.17-rc5
Date: Sat, 26 Feb 2022 10:49:47 -0600 [thread overview]
Message-ID: <20220226164948.712767-1-aford173@gmail.com> (raw)
Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5
with some additional pending changes to address issues with
wrong pin-muxing on the OMAP35.
Signed-off-by: Adam Ford <aford173@gmail.com>
diff --git a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
index f7a841a288..f690bc83bf 100644
--- a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
@@ -9,5 +9,19 @@
/ {
model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
- compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3";
+ compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
};
diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
index a604d92221..e28e9625be 100644
--- a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
@@ -11,3 +11,17 @@
model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
};
+
+&omap3_pmx_core2 {
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+};
diff --git a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
index 100396f6c2..7d0468a237 100644
--- a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
+++ b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
@@ -51,6 +51,8 @@
&mcbsp2 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp2_pins>;
};
&charger {
@@ -77,7 +79,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
vdda_video-supply = <&video_reg>;
pinctrl-names = "default";
@@ -102,35 +104,18 @@
regulator-max-microvolt = <3300000>;
};
- lcd0: display@0 {
- compatible = "panel-dpi";
- label = "28";
- status = "okay";
- /* default-on; */
+ lcd0: display {
+ /* This isn't the exact LCD, but the timings meet spec */
+ compatible = "logicpd,type28";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pin>;
- enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
+ backlight = <&bl>;
+ enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
port {
lcd_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
-
- panel-timing {
- clock-frequency = <9000000>;
- hactive = <480>;
- vactive = <272>;
- hfront-porch = <3>;
- hback-porch = <2>;
- hsync-len = <42>;
- vback-porch = <3>;
- vfront-porch = <2>;
- vsync-len = <11>;
- hsync-active = <1>;
- vsync-active = <1>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
};
bl: backlight {
diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi
index b56524cc7f..385bc8d793 100644
--- a/arch/arm/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/dts/logicpd-som-lv.dtsi
@@ -27,6 +27,8 @@
/* HS USB Host PHY on PORT 1 */
hsusb2_phy: hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_reset_pin>;
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
#phy-cells = <0>;
@@ -144,6 +146,8 @@
};
&usbhshost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>, <&hsusb2_2_pins>;
port2-mode = "ehci-phy";
};
@@ -153,8 +157,6 @@
&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_pins>;
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
@@ -166,6 +168,7 @@
OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
>;
};
+
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
@@ -183,6 +186,7 @@
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
>;
};
+
mcspi1_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
@@ -250,13 +254,13 @@
};
&omap3_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_reset_pin>;
+
hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
+
wl127x_gpio: pinmux_wl127x_gpio_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
@@ -265,21 +269,6 @@
};
};
-&omap3_pmx_core2 {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_2_pins>;
- hsusb2_2_pins: pinmux_hsusb2_2_pins {
- pinctrl-single,pins = <
- OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
- OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
- OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
- OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
- OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
- OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
- >;
- };
-};
-
&uart2 {
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
pinctrl-names = "default";
--
2.34.1
next reply other threads:[~2022-02-26 16:50 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-02-26 16:49 Adam Ford [this message]
2022-02-26 16:49 ` [PATCH 2/2] ARM: omap3_logic: Remove hard-coded USB muxing Adam Ford
2022-03-14 13:08 ` Tom Rini
2022-03-14 13:08 ` [PATCH 1/2] ARM: dts: logicpd-som-lv: Resync DTS files with Linux 5.17-rc5 Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220226164948.712767-1-aford173@gmail.com \
--to=aford173@gmail.com \
--cc=aford@beaconembedded.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.