From: Sam Ravnborg <sam@ravnborg.org>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Boris Brezillon <bbrezillon@kernel.org>,
Nicolas Ferre <nicolas.ferre@microchip.com>,
dri-devel@lists.freedesktop.org,
Claudiu Beznea <claudiu.beznea@microchip.com>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] drm: atmel-hlcdc: Support inverting the pixel clock polarity
Date: Sat, 10 Jun 2023 22:05:15 +0200 [thread overview]
Message-ID: <20230610200515.GA1041001@ravnborg.org> (raw)
In-Reply-To: <20230609144843.851327-1-miquel.raynal@bootlin.com>
On Fri, Jun 09, 2023 at 04:48:43PM +0200, Miquel Raynal wrote:
> On the SoC host controller, the pixel clock can be:
> * standard: data is launched on the rising edge
> * inverted: data is launched on the falling edge
>
> Some panels may need the inverted option to be used so let's support
> this DRM flag.
>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Hi Miquel,
the patch is:
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
I hope someone else can pick it up and apply it to drm-misc as
my drm-misc setup is hopelessly outdated atm.
Sam
> ---
>
> Hello, this change was tested on a Sama5d36 based custom board with a
> panel not behaving correctly if the pixel clock was not inverted.
> Cheers, Miquèl
>
> .../gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 25 +++++++++++++++++++
> 1 file changed, 25 insertions(+)
>
> diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> index 58184cd6ab0b..cc5cf4c2faf7 100644
> --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> @@ -68,7 +68,11 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
> struct atmel_hlcdc_crtc *crtc = drm_crtc_to_atmel_hlcdc_crtc(c);
> struct regmap *regmap = crtc->dc->hlcdc->regmap;
> struct drm_display_mode *adj = &c->state->adjusted_mode;
> + struct drm_encoder *encoder = NULL, *en_iter;
> + struct drm_connector *connector = NULL;
> struct atmel_hlcdc_crtc_state *state;
> + struct drm_device *ddev = c->dev;
> + struct drm_connector_list_iter iter;
> unsigned long mode_rate;
> struct videomode vm;
> unsigned long prate;
> @@ -76,6 +80,23 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
> unsigned int cfg = 0;
> int div, ret;
>
> + /* get encoder from crtc */
> + drm_for_each_encoder(en_iter, ddev) {
> + if (en_iter->crtc == c) {
> + encoder = en_iter;
> + break;
> + }
> + }
> +
> + if (encoder) {
> + /* Get the connector from encoder */
> + drm_connector_list_iter_begin(ddev, &iter);
> + drm_for_each_connector_iter(connector, &iter)
> + if (connector->encoder == encoder)
> + break;
> + drm_connector_list_iter_end(&iter);
> + }
> +
> ret = clk_prepare_enable(crtc->dc->hlcdc->sys_clk);
> if (ret)
> return;
> @@ -134,6 +155,10 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
>
> cfg |= ATMEL_HLCDC_CLKDIV(div);
>
> + if (connector &&
> + connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
> + cfg |= ATMEL_HLCDC_CLKPOL;
> +
> regmap_update_bits(regmap, ATMEL_HLCDC_CFG(0), mask, cfg);
>
> state = drm_crtc_state_to_atmel_hlcdc_crtc_state(c->state);
> --
> 2.34.1
next prev parent reply other threads:[~2023-06-10 20:05 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-09 14:48 [PATCH] drm: atmel-hlcdc: Support inverting the pixel clock polarity Miquel Raynal
2023-06-09 14:48 ` Miquel Raynal
2023-06-10 20:05 ` Sam Ravnborg [this message]
2023-07-12 15:57 ` Miquel Raynal
2023-07-12 15:57 ` Miquel Raynal
2023-08-07 9:12 ` Miquel Raynal
2023-08-07 9:12 ` Miquel Raynal
2023-08-07 16:52 ` Sam Ravnborg
2023-08-07 16:52 ` Sam Ravnborg
2023-08-08 6:33 ` Miquel Raynal
2023-08-08 6:33 ` Miquel Raynal
2023-08-10 6:45 ` Boris Brezillon
2023-08-10 6:45 ` Boris Brezillon
2023-08-10 17:31 ` Sam Ravnborg
2023-08-10 17:31 ` Sam Ravnborg
2023-08-11 5:53 ` Miquel Raynal
2023-08-11 5:53 ` Miquel Raynal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230610200515.GA1041001@ravnborg.org \
--to=sam@ravnborg.org \
--cc=alexandre.belloni@bootlin.com \
--cc=bbrezillon@kernel.org \
--cc=claudiu.beznea@microchip.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=nicolas.ferre@microchip.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.