From: Paul Gortmaker <paul.gortmaker@windriver.com>
To: <linuxppc-dev@lists.ozlabs.org>
Cc: Li Yang <leoyang.li@nxp.com>, Scott Wood <oss@buserror.net>,
Paul Gortmaker <paul.gortmaker@windriver.com>,
Claudiu Manoil <claudiu.manoil@nxp.com>,
Paul Mackerras <paulus@samba.org>
Subject: [PATCH 1/2] powerpc: drop MPC8540_ADS and MPC8560_ADS platform support
Date: Tue, 20 Jun 2023 00:32:59 -0400 [thread overview]
Message-ID: <20230620043300.197546-2-paul.gortmaker@windriver.com> (raw)
In-Reply-To: <20230620043300.197546-1-paul.gortmaker@windriver.com>
Based on the revision history in the manual(s), these e500-v1
platforms were first available around 2002.
Like a lot of evaluation boards, they attempted to provide break-out
connectors for all possible features, and that combined with four
PCI-X slots (and the age/era) meant for a considerably large board.
As I recall it, from a Linux point of view, the biggest difference
between 8540 and 8560 was in the UART implementation, and that is
reflected in a diff of the defconfigs.
In any case, these are over 20 years old, and by today's standards
only have a small amount of DDR1 memory, and were not widely available.
Given that, it makes sense to remove support from them in 2023.
Cc: Scott Wood <oss@buserror.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
arch/powerpc/boot/Makefile | 2 -
arch/powerpc/boot/dts/fsl/mpc8540ads.dts | 355 ----------------
arch/powerpc/boot/dts/fsl/mpc8560ads.dts | 388 ------------------
.../configs/85xx/mpc8540_ads_defconfig | 47 ---
.../configs/85xx/mpc8560_ads_defconfig | 50 ---
arch/powerpc/configs/mpc85xx_base.config | 2 -
arch/powerpc/platforms/85xx/Makefile | 2 -
arch/powerpc/platforms/85xx/mpc85xx_ads.c | 162 --------
8 files changed, 1008 deletions(-)
delete mode 100644 arch/powerpc/boot/dts/fsl/mpc8540ads.dts
delete mode 100644 arch/powerpc/boot/dts/fsl/mpc8560ads.dts
delete mode 100644 arch/powerpc/configs/85xx/mpc8540_ads_defconfig
delete mode 100644 arch/powerpc/configs/85xx/mpc8560_ads_defconfig
delete mode 100644 arch/powerpc/platforms/85xx/mpc85xx_ads.c
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index bf8976563e02..cf728cb3e9a9 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -342,8 +342,6 @@ image-$(CONFIG_MPC834x_ITX) += cuImage.mpc8349emitx \
image-$(CONFIG_ASP834x) += dtbImage.asp834x-redboot
# Board ports in arch/powerpc/platform/85xx/Kconfig
-image-$(CONFIG_MPC8540_ADS) += cuImage.mpc8540ads
-image-$(CONFIG_MPC8560_ADS) += cuImage.mpc8560ads
image-$(CONFIG_MPC85xx_CDS) += cuImage.mpc8541cds \
cuImage.mpc8548cds_32b \
cuImage.mpc8555cds
diff --git a/arch/powerpc/boot/dts/fsl/mpc8540ads.dts b/arch/powerpc/boot/dts/fsl/mpc8540ads.dts
deleted file mode 100644
index e03ae130162b..000000000000
--- a/arch/powerpc/boot/dts/fsl/mpc8540ads.dts
+++ /dev/null
@@ -1,355 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * MPC8540 ADS Device Tree Source
- *
- * Copyright 2006, 2008 Freescale Semiconductor Inc.
- */
-
-/dts-v1/;
-
-/include/ "e500v1_power_isa.dtsi"
-
-/ {
- model = "MPC8540ADS";
- compatible = "MPC8540ADS", "MPC85xxADS";
- #address-cells = <1>;
- #size-cells = <1>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8540@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <0>; // 33 MHz, from uboot
- bus-frequency = <0>; // 166 MHz
- clock-frequency = <0>; // 825 MHz, from uboot
- next-level-cache = <&L2>;
- };
- };
-
- memory {
- device_type = "memory";
- reg = <0x0 0x8000000>; // 128M at 0x0
- };
-
- soc8540@e0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0xe0000000 0x100000>;
- bus-frequency = <0>;
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <8>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8540-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8540-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8540-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2, 256K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- i2c@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- dfsrr;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8540-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8540-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8540-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8540-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x3>;
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi1>;
- phy-handle = <&phy1>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet2: ethernet@26000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <2>;
- device_type = "network";
- model = "FEC";
- compatible = "gianfar";
- reg = <0x26000 0x1000>;
- ranges = <0x0 0x26000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <41 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi2>;
- phy-handle = <&phy3>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- serial0: serial@4500 {
- cell-index = <0>;
- device_type = "serial";
- compatible = "fsl,ns16550", "ns16550";
- reg = <0x4500 0x100>; // reg base, size
- clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
-
- serial1: serial@4600 {
- cell-index = <1>;
- device_type = "serial";
- compatible = "fsl,ns16550", "ns16550";
- reg = <0x4600 0x100>; // reg base, size
- clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <42 2>;
- interrupt-parent = <&mpic>;
- };
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
- };
-
- pci0: pci@e0008000 {
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
-
- /* IDSEL 0x02 */
- 0x1000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x1000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x1000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x1000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 0x03 */
- 0x1800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x1800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x1800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x1800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 0x04 */
- 0x2000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x2000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x2000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x2000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x05 */
- 0x2800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x2800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x2800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x2800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x0c */
- 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x6000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 0x0d */
- 0x6800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x6800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x6800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x6800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 0x0e */
- 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x7000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x7000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x7000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x0f */
- 0x7800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x7800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x7800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x7800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 0x12 */
- 0x9000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 0x13 */
- 0x9800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x9800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x9800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x9800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 0x14 */
- 0xa000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0xa000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0xa000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0xa000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x15 */
- 0xa800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0xa800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0xa800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0xa800 0x0 0x0 0x4 &mpic 0x1 0x1>;
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- bus-range = <0 0>;
- ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
- clock-frequency = <66666666>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- reg = <0xe0008000 0x1000>;
- compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
- device_type = "pci";
- };
-};
diff --git a/arch/powerpc/boot/dts/fsl/mpc8560ads.dts b/arch/powerpc/boot/dts/fsl/mpc8560ads.dts
deleted file mode 100644
index c2f9aea78b29..000000000000
--- a/arch/powerpc/boot/dts/fsl/mpc8560ads.dts
+++ /dev/null
@@ -1,388 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * MPC8560 ADS Device Tree Source
- *
- * Copyright 2006, 2008 Freescale Semiconductor Inc.
- */
-
-/dts-v1/;
-
-/include/ "e500v1_power_isa.dtsi"
-
-/ {
- model = "MPC8560ADS";
- compatible = "MPC8560ADS", "MPC85xxADS";
- #address-cells = <1>;
- #size-cells = <1>;
-
- aliases {
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- ethernet3 = &enet3;
- serial0 = &serial0;
- serial1 = &serial1;
- pci0 = &pci0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,8560@0 {
- device_type = "cpu";
- reg = <0x0>;
- d-cache-line-size = <32>; // 32 bytes
- i-cache-line-size = <32>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <82500000>;
- bus-frequency = <330000000>;
- clock-frequency = <825000000>;
- };
- };
-
- memory {
- device_type = "memory";
- reg = <0x0 0x10000000>;
- };
-
- soc8560@e0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0xe0000000 0x100000>;
- bus-frequency = <330000000>;
-
- ecm-law@0 {
- compatible = "fsl,ecm-law";
- reg = <0x0 0x1000>;
- fsl,num-laws = <8>;
- };
-
- ecm@1000 {
- compatible = "fsl,mpc8560-ecm", "fsl,ecm";
- reg = <0x1000 0x1000>;
- interrupts = <17 2>;
- interrupt-parent = <&mpic>;
- };
-
- memory-controller@2000 {
- compatible = "fsl,mpc8540-memory-controller";
- reg = <0x2000 0x1000>;
- interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- };
-
- L2: l2-cache-controller@20000 {
- compatible = "fsl,mpc8540-l2-cache-controller";
- reg = <0x20000 0x1000>;
- cache-line-size = <32>; // 32 bytes
- cache-size = <0x40000>; // L2, 256K
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
-
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
- reg = <0x21300 0x4>;
- ranges = <0x0 0x21100 0x200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8560-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x0 0x80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <20 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8560-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x80 0x80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <21 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8560-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x100 0x80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <22 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8560-dma-channel",
- "fsl,eloplus-dma-channel";
- reg = <0x180 0x80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <23 2>;
- };
- };
-
- enet0: ethernet@24000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <0>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <0x24000 0x1000>;
- ranges = <0x0 0x24000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2 30 2 34 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi0>;
- phy-handle = <&phy0>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x3>;
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- enet1: ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cell-index = <1>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <0x25000 0x1000>;
- ranges = <0x0 0x25000 0x1000>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <35 2 36 2 40 2>;
- interrupt-parent = <&mpic>;
- tbi-handle = <&tbi1>;
- phy-handle = <&phy1>;
-
- mdio@520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
- };
-
- mpic: pic@40000 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0x40000 0x40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- cpm@919c0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
- reg = <0x919c0 0x30>;
- ranges;
-
- muram@80000 {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0x0 0x80000 0x10000>;
-
- data@0 {
- compatible = "fsl,cpm-muram-data";
- reg = <0x0 0x4000 0x9000 0x2000>;
- };
- };
-
- brg@919f0 {
- compatible = "fsl,mpc8560-brg",
- "fsl,cpm2-brg",
- "fsl,cpm-brg";
- reg = <0x919f0 0x10 0x915f0 0x10>;
- clock-frequency = <165000000>;
- };
-
- cpmpic: pic@90c00 {
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- interrupts = <46 2>;
- interrupt-parent = <&mpic>;
- reg = <0x90c00 0x80>;
- compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
- };
-
- serial0: serial@91a00 {
- device_type = "serial";
- compatible = "fsl,mpc8560-scc-uart",
- "fsl,cpm2-scc-uart";
- reg = <0x91a00 0x20 0x88000 0x100>;
- fsl,cpm-brg = <1>;
- fsl,cpm-command = <0x800000>;
- current-speed = <115200>;
- interrupts = <40 8>;
- interrupt-parent = <&cpmpic>;
- };
-
- serial1: serial@91a20 {
- device_type = "serial";
- compatible = "fsl,mpc8560-scc-uart",
- "fsl,cpm2-scc-uart";
- reg = <0x91a20 0x20 0x88100 0x100>;
- fsl,cpm-brg = <2>;
- fsl,cpm-command = <0x4a00000>;
- current-speed = <115200>;
- interrupts = <41 8>;
- interrupt-parent = <&cpmpic>;
- };
-
- enet2: ethernet@91320 {
- device_type = "network";
- compatible = "fsl,mpc8560-fcc-enet",
- "fsl,cpm2-fcc-enet";
- reg = <0x91320 0x20 0x88500 0x100 0x913b0 0x1>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- fsl,cpm-command = <0x16200300>;
- interrupts = <33 8>;
- interrupt-parent = <&cpmpic>;
- phy-handle = <&phy2>;
- };
-
- enet3: ethernet@91340 {
- device_type = "network";
- compatible = "fsl,mpc8560-fcc-enet",
- "fsl,cpm2-fcc-enet";
- reg = <0x91340 0x20 0x88600 0x100 0x913d0 0x1>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- fsl,cpm-command = <0x1a400300>;
- interrupts = <34 8>;
- interrupt-parent = <&cpmpic>;
- phy-handle = <&phy3>;
- };
- };
- };
-
- pci0: pci@e0008000 {
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
- device_type = "pci";
- reg = <0xe0008000 0x1000>;
- clock-frequency = <66666666>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
-
- /* IDSEL 0x2 */
- 0x1000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x1000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x1000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x1000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 0x3 */
- 0x1800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x1800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x1800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x1800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 0x4 */
- 0x2000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x2000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x2000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x2000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 0x5 */
- 0x2800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x2800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x2800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x2800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 12 */
- 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x6000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 13 */
- 0x6800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x6800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x6800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x6800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 14*/
- 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0x7000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0x7000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0x7000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 15 */
- 0x7800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0x7800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0x7800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0x7800 0x0 0x0 0x4 &mpic 0x1 0x1
-
- /* IDSEL 18 */
- 0x9000 0x0 0x0 0x1 &mpic 0x1 0x1
- 0x9000 0x0 0x0 0x2 &mpic 0x2 0x1
- 0x9000 0x0 0x0 0x3 &mpic 0x3 0x1
- 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
-
- /* IDSEL 19 */
- 0x9800 0x0 0x0 0x1 &mpic 0x4 0x1
- 0x9800 0x0 0x0 0x2 &mpic 0x1 0x1
- 0x9800 0x0 0x0 0x3 &mpic 0x2 0x1
- 0x9800 0x0 0x0 0x4 &mpic 0x3 0x1
-
- /* IDSEL 20 */
- 0xa000 0x0 0x0 0x1 &mpic 0x3 0x1
- 0xa000 0x0 0x0 0x2 &mpic 0x4 0x1
- 0xa000 0x0 0x0 0x3 &mpic 0x1 0x1
- 0xa000 0x0 0x0 0x4 &mpic 0x2 0x1
-
- /* IDSEL 21 */
- 0xa800 0x0 0x0 0x1 &mpic 0x2 0x1
- 0xa800 0x0 0x0 0x2 &mpic 0x3 0x1
- 0xa800 0x0 0x0 0x3 &mpic 0x4 0x1
- 0xa800 0x0 0x0 0x4 &mpic 0x1 0x1>;
-
- interrupt-parent = <&mpic>;
- interrupts = <24 2>;
- bus-range = <0 0>;
- ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x0 0xe2000000 0x0 0x1000000>;
- };
-};
diff --git a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig b/arch/powerpc/configs/85xx/mpc8540_ads_defconfig
deleted file mode 100644
index 618e03e0706d..000000000000
--- a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig
+++ /dev/null
@@ -1,47 +0,0 @@
-CONFIG_PPC_85xx=y
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_MSDOS_PARTITION is not set
-CONFIG_MPC8540_ADS=y
-CONFIG_GEN_RTC=y
-CONFIG_BINFMT_MISC=y
-CONFIG_MATH_EMULATION=y
-# CONFIG_SECCOMP is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_USER=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_IPV6 is not set
-# CONFIG_FW_LOADER is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=32768
-CONFIG_NETDEVICES=y
-CONFIG_GIANFAR=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_EXT2_FS=y
-CONFIG_EXT4_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_DETECT_HUNG_TASK=y
-CONFIG_DEBUG_MUTEXES=y
diff --git a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig b/arch/powerpc/configs/85xx/mpc8560_ads_defconfig
deleted file mode 100644
index 9bc6283f2fb2..000000000000
--- a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig
+++ /dev/null
@@ -1,50 +0,0 @@
-CONFIG_PPC_85xx=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_MSDOS_PARTITION is not set
-CONFIG_MPC8560_ADS=y
-CONFIG_GEN_RTC=y
-CONFIG_BINFMT_MISC=y
-CONFIG_MATH_EMULATION=y
-# CONFIG_SECCOMP is not set
-CONFIG_PCI=y
-CONFIG_PCI_DEBUG=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_IPV6 is not set
-# CONFIG_FW_LOADER is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=32768
-CONFIG_NETDEVICES=y
-CONFIG_FS_ENET=y
-# CONFIG_FS_ENET_HAS_SCC is not set
-CONFIG_GIANFAR=y
-CONFIG_E1000=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_MARVELL_PHY=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_CPM=y
-CONFIG_SERIAL_CPM_CONSOLE=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT4_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_DETECT_HUNG_TASK=y
-CONFIG_DEBUG_MUTEXES=y
diff --git a/arch/powerpc/configs/mpc85xx_base.config b/arch/powerpc/configs/mpc85xx_base.config
index 85907b776908..e13bcf83bd1d 100644
--- a/arch/powerpc/configs/mpc85xx_base.config
+++ b/arch/powerpc/configs/mpc85xx_base.config
@@ -1,7 +1,5 @@
CONFIG_MATH_EMULATION=y
CONFIG_MPC8536_DS=y
-CONFIG_MPC8540_ADS=y
-CONFIG_MPC8560_ADS=y
CONFIG_MPC85xx_CDS=y
CONFIG_MPC85xx_DS=y
CONFIG_MPC85xx_MDS=y
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index e3d977624e33..4bb473ca51b4 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -12,8 +12,6 @@ obj-y += common.o
obj-$(CONFIG_BSC9131_RDB) += bsc913x_rdb.o
obj-$(CONFIG_BSC9132_QDS) += bsc913x_qds.o
obj-$(CONFIG_C293_PCIE) += c293pcie.o
-obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
-obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
obj-$(CONFIG_MPC8536_DS) += mpc8536_ds.o
obj8259-$(CONFIG_PPC_I8259) += mpc85xx_8259.o
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
deleted file mode 100644
index 7c67438e76f8..000000000000
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ /dev/null
@@ -1,162 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * MPC85xx setup and early boot code plus other random bits.
- *
- * Maintained by Kumar Gala (see MAINTAINERS for contact information)
- *
- * Copyright 2005 Freescale Semiconductor Inc.
- */
-
-#include <linux/stddef.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/kdev_t.h>
-#include <linux/delay.h>
-#include <linux/seq_file.h>
-#include <linux/of_platform.h>
-
-#include <asm/time.h>
-#include <asm/machdep.h>
-#include <asm/pci-bridge.h>
-#include <asm/mpic.h>
-#include <mm/mmu_decl.h>
-#include <asm/udbg.h>
-
-#include <sysdev/fsl_soc.h>
-#include <sysdev/fsl_pci.h>
-
-#ifdef CONFIG_CPM2
-#include <asm/cpm2.h>
-#include <sysdev/cpm2_pic.h>
-#endif
-
-#include "mpc85xx.h"
-
-static void __init mpc85xx_ads_pic_init(void)
-{
- struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN,
- 0, 256, " OpenPIC ");
- BUG_ON(mpic == NULL);
- mpic_init(mpic);
-
- mpc85xx_cpm2_pic_init();
-}
-
-/*
- * Setup the architecture
- */
-#ifdef CONFIG_CPM2
-struct cpm_pin {
- int port, pin, flags;
-};
-
-static const struct cpm_pin mpc8560_ads_pins[] = {
- /* SCC1 */
- {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
- {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
-
- /* SCC2 */
- {2, 12, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {2, 13, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {3, 26, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {3, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {3, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
-
- /* FCC2 */
- {1, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 20, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 22, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 25, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 26, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 27, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
- {1, 30, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {2, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK14 */
- {2, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK13 */
-
- /* FCC3 */
- {1, 4, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 6, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 8, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 9, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 12, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 13, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 14, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 15, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {1, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {2, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK16 */
- {2, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK15 */
- {2, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
-};
-
-static void __init init_ioports(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(mpc8560_ads_pins); i++) {
- const struct cpm_pin *pin = &mpc8560_ads_pins[i];
- cpm2_set_pin(pin->port, pin->pin, pin->flags);
- }
-
- cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
- cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
- cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_RX);
- cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_TX);
- cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK13, CPM_CLK_RX);
- cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK14, CPM_CLK_TX);
- cpm2_clk_setup(CPM_CLK_FCC3, CPM_CLK15, CPM_CLK_RX);
- cpm2_clk_setup(CPM_CLK_FCC3, CPM_CLK16, CPM_CLK_TX);
-}
-#endif
-
-static void __init mpc85xx_ads_setup_arch(void)
-{
- if (ppc_md.progress)
- ppc_md.progress("mpc85xx_ads_setup_arch()", 0);
-
-#ifdef CONFIG_CPM2
- cpm2_reset();
- init_ioports();
-#endif
-
- fsl_pci_assign_primary();
-}
-
-static void mpc85xx_ads_show_cpuinfo(struct seq_file *m)
-{
- uint pvid, svid, phid1;
-
- pvid = mfspr(SPRN_PVR);
- svid = mfspr(SPRN_SVR);
-
- seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
- seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
- seq_printf(m, "SVR\t\t: 0x%x\n", svid);
-
- /* Display cpu Pll setting */
- phid1 = mfspr(SPRN_HID1);
- seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-}
-
-machine_arch_initcall(mpc85xx_ads, mpc85xx_common_publish_devices);
-
-define_machine(mpc85xx_ads) {
- .name = "MPC85xx ADS",
- .compatible = "MPC85xxADS",
- .setup_arch = mpc85xx_ads_setup_arch,
- .init_IRQ = mpc85xx_ads_pic_init,
- .show_cpuinfo = mpc85xx_ads_show_cpuinfo,
- .get_irq = mpic_get_irq,
- .progress = udbg_progress,
-};
--
2.25.1
next prev parent reply other threads:[~2023-06-20 4:46 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-20 4:32 [PATCH v2 0/2] Remove some e500/MPC85xx evaluation platforms Paul Gortmaker
2023-06-20 4:32 ` Paul Gortmaker [this message]
2023-06-20 4:33 ` [PATCH 2/2] powerpc: drop MPC85xx_CDS platform support Paul Gortmaker
2023-07-03 5:26 ` [PATCH v2 0/2] Remove some e500/MPC85xx evaluation platforms Michael Ellerman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230620043300.197546-2-paul.gortmaker@windriver.com \
--to=paul.gortmaker@windriver.com \
--cc=claudiu.manoil@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=oss@buserror.net \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.