[PATCH v4 0/6] GC0308 Camera Sensor

[Sebastian Reichel <sre@kernel.org>]

Hi,

I did the following tests on an i.MX6ULL based system [0]:

 * v4l2-compliance -u /dev/v4l-subdev1
   - v4l2-compliance 1.24.1, 32 bits, 32-bit time_t
     (from Debian testing)
   - Total for device /dev/v4l-subdev1: 44, Succeeded: 44
 * Using gstreamer + v4l2-ctl
   - Tried 640x480, 320x240, 160x120 YUYV8_2X8 formats
   - Tested effect of all exposed user controls
 * checkpatch does not report any driver issues
 * dt_binding_check does not report anything
 * rebinding driver works

[0] https://embedded-recipes.org/2023/schedule/running-foss-thermal-camera/

Changes since PATCHv3:
 * https://lore.kernel.org/all/20231027011417.2174658-1-sre@kernel.org/
 * Rebased to v6.7-rc1
 * Replace gc0308_is_valid_format() with gc0308_get_format_idx(),
   which can be reused in gc0308_set_format().
 * Remove the runtime PM get call in remove function
 * Move the runtime PM get call before the subdev register call in probe
 * Drop message about unsupported format code
 * Add Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
 * Merged binding patch with the one from Alain Volmat and add
   Acked-by: Rob Herring <robh@kernel.org> and assign authorship
   to him, since his patch arrived first on the ML
 * Added two patches to fix an issue with v4l2_async_unregister_subdev()
   list handling

Changes since PATCHv2:
 * https://lore.kernel.org/all/20231024010355.1877523-1-sre@kernel.org/
 * Simplify Kconfig dependencies
 * Do not store code/resolution; which is available from subdev state
 * Store register values for mode settings to avoid second lookup in
   s_stream
 * Reduce power_on sleep times
 * remove debug dev_err() print, that I accidently added in v2
 * add missing format check in gc0308_enum_frame_size()
 * do not PM resume in gc0308_s_ctrl()
 * enable and use runtime PM autosuspend
 * add .init_cfg() PAD op
 * use CCI helper instead of raw regmap
 * cluster both flip controls
   (that's not just a performance optimization, but fixes an issue,
   that register update is slow, so fast sequential setting of VFLIP/HFLIP
   override each other without this)
 * simplify gc0308_set_power_line_freq
 * free control handler on probe error
 * use first format by default
 * expose V4L2_CID_HBLANK, V4L2_CID_VBLANK, V4L2_CID_PIXEL_RATE
 * remove incorrect support for framerate and instead add a comment

Changes since PATCHv1:
 * https://lore.kernel.org/all/20231023002547.1754190-1-sre@kernel.org/
 * Update binding: i2c0 -> i2c
 * Update binding: make GC0309 use GC0308 as fallback compatible
 * Add regulator handling in power_on/power_off
 * Fix alignment of regmap_multi_reg_write arguments
 * Fix useless extra return
 * Do not check for pad in gc0308_enum_frame_size()
 * Drop get_mbus_config implementation
 * Use V4L2_CID_AUTO_EXPOSURE_BIAS instead of V4L2_CID_EXPOSURE
 * Drop gc0308_get_format in favour of v4l2_subdev_get_fmt
 * Replace open-coded v4l2_find_nearest_size() logic
 * check clock rate instead of setting it
 * use fwnode_graph_get_endpoint_by_id()
 * power off device when probe errors out after power on
 * replace mutex with sub-device state
 * add Galaxycore to generic camera sensors section in MAINTAINERS
 * add GC0308 entry in MAINTAINERS

Greetings,

-- Sebastian

Alain Volmat (1):
  dt-bindings: vendor-prefixes: add GalaxyCore

Sebastian Reichel (5):
  media: dt-bindings: gc0308: add binding
  media: MAINTAINERS: Add GalaxyCore in camera sensor section
  media: v4l: async: Fix duplicated list deletion
  media: v4l: async: Drop useless list move operation
  media: i2c: gc0308: new driver

 .../bindings/media/i2c/galaxycore,gc0308.yaml |  108 ++
 .../devicetree/bindings/vendor-prefixes.yaml  |    2 +
 MAINTAINERS                                   |    8 +
 drivers/media/i2c/Kconfig                     |   10 +
 drivers/media/i2c/Makefile                    |    1 +
 drivers/media/i2c/gc0308.c                    | 1436 +++++++++++++++++
 drivers/media/v4l2-core/v4l2-async.c          |    4 -
 7 files changed, 1565 insertions(+), 4 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml
 create mode 100644 drivers/media/i2c/gc0308.c

-- 
2.42.0