From: Andrei Simion <andrei.simion@microchip.com>
To: <claudiu.beznea@tuxon.dev>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>, <peda@axentia.se>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<cristian.birsan@microchip.com>,
Andrei Simion <andrei.simion@microchip.com>
Subject: [PATCH 5/5] ARM: dts: microchip: Rename LED sub nodes name
Date: Wed, 14 Aug 2024 15:26:33 +0300 [thread overview]
Message-ID: <20240814122633.198562-6-andrei.simion@microchip.com> (raw)
In-Reply-To: <20240814122633.198562-1-andrei.simion@microchip.com>
dtbs_check warnings:
leds: 'd[0-9]', 'ds[0-9]' do not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
leds: 'red', 'green', 'blue' do not match any of regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Rename the led sub nodes according to devicetree
specification and leds-gpio.yaml.
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
---
Split the bloadted patch into small patches on topics
based on comments:
https://lore.kernel.org/linux-arm-kernel/89f51615-0dee-4ab0-ab72-e3c057fee1e7@tuxon.dev/
---
arch/arm/boot/dts/microchip/aks-cdu.dts | 8 ++++----
arch/arm/boot/dts/microchip/animeo_ip.dts | 8 ++++----
arch/arm/boot/dts/microchip/at91-sam9x60ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91rm9200ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91sam9260ek.dts | 4 ++--
arch/arm/boot/dts/microchip/at91sam9261ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91sam9263ek.dts | 4 ++--
arch/arm/boot/dts/microchip/at91sam9g20ek.dts | 4 ++--
8 files changed, 23 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/microchip/aks-cdu.dts b/arch/arm/boot/dts/microchip/aks-cdu.dts
index 52e166c8a365..95a0639c5579 100644
--- a/arch/arm/boot/dts/microchip/aks-cdu.dts
+++ b/arch/arm/boot/dts/microchip/aks-cdu.dts
@@ -98,23 +98,23 @@ rootfs@500000 {
leds {
compatible = "gpio-leds";
- red {
+ led-red {
gpios = <&pioC 10 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
};
- green {
+ led-green {
gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
default-state = "on";
};
- yellow {
+ led-yellow {
gpios = <&pioB 20 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
- blue {
+ led-blue {
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
diff --git a/arch/arm/boot/dts/microchip/animeo_ip.dts b/arch/arm/boot/dts/microchip/animeo_ip.dts
index 911c8d9ee013..52ac840bcd35 100644
--- a/arch/arm/boot/dts/microchip/animeo_ip.dts
+++ b/arch/arm/boot/dts/microchip/animeo_ip.dts
@@ -146,23 +146,23 @@ ohci: usb@500000 {
leds {
compatible = "gpio-leds";
- power_green {
+ led-power-green {
label = "power_green";
gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- power_red {
+ led-power-red {
label = "power_red";
gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
};
- tx_green {
+ led-tx-green {
label = "tx_green";
gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
};
- tx_red {
+ led-tx-red {
label = "tx_red";
gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
};
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
index b9a21f9f9a6d..da31b07d6828 100644
--- a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
@@ -53,17 +53,17 @@ leds {
pinctrl-0 = <&pinctrl_gpio_leds>;
status = "okay"; /* Conflict with pwm0. */
- red {
+ led-red {
label = "red";
gpios = <&pioB 11 GPIO_ACTIVE_HIGH>;
};
- green {
+ led-green {
label = "green";
gpios = <&pioB 12 GPIO_ACTIVE_HIGH>;
};
- blue {
+ led-blue {
label = "blue";
gpios = <&pioB 13 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91rm9200ek.dts b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
index 3089912dd6be..641d443e6ca9 100644
--- a/arch/arm/boot/dts/microchip/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
@@ -127,19 +127,19 @@ root@350000 {
leds {
compatible = "gpio-leds";
- ds2 {
+ led-ds2 {
label = "green";
gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "mmc0";
};
- ds4 {
+ led-ds4 {
label = "yellow";
gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
- ds6 {
+ led-ds6 {
label = "red";
gpios = <&pioB 2 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm/boot/dts/microchip/at91sam9260ek.dts b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
index ed259e2cb853..4933971d0585 100644
--- a/arch/arm/boot/dts/microchip/at91sam9260ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
@@ -174,13 +174,13 @@ eeprom@50 {
leds {
compatible = "gpio-leds";
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm/boot/dts/microchip/at91sam9261ek.dts b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
index 4d9269cc5f32..9c44177db714 100644
--- a/arch/arm/boot/dts/microchip/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
@@ -192,19 +192,19 @@ watchdog@fffffd40 {
leds {
compatible = "gpio-leds";
- ds8 {
+ led-ds8 {
label = "ds8";
gpios = <&pioA 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
- ds7 {
+ led-ds7 {
label = "ds7";
gpios = <&pioA 14 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
};
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91sam9263ek.dts b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
index a8ea36db4c04..cf5434f9449d 100644
--- a/arch/arm/boot/dts/microchip/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
@@ -219,13 +219,13 @@ &pioA 21 GPIO_ACTIVE_HIGH
leds {
compatible = "gpio-leds";
- d3 {
+ led-d3 {
label = "d3";
gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- d2 {
+ led-d2 {
label = "d2";
gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
diff --git a/arch/arm/boot/dts/microchip/at91sam9g20ek.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
index 6de7a7cd3c07..1e62fd371ddb 100644
--- a/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
@@ -14,13 +14,13 @@ / {
leds {
compatible = "gpio-leds";
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
};
--
2.34.1
next prev parent reply other threads:[~2024-08-14 12:32 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-14 12:26 [PATCH 0/5] Cosmetic Work for ARM/Microchip (AT91) Andrei Simion
2024-08-14 12:26 ` [PATCH 1/5] ARM: dts: microchip: Clean up spacing and indentation Andrei Simion
2024-08-14 13:20 ` Krzysztof Kozlowski
2024-08-14 13:32 ` Andrei.Simion
2024-08-14 13:57 ` Krzysztof Kozlowski
2024-08-14 14:20 ` Andrei.Simion
2024-08-14 12:26 ` [PATCH 2/5] ARM: dts: microchip: Rename the eeprom nodename Andrei Simion
2024-08-14 12:26 ` [PATCH 3/5] ARM: dts: microchip: Rename the pmic node Andrei Simion
2024-08-14 13:20 ` Krzysztof Kozlowski
2024-08-14 13:58 ` Krzysztof Kozlowski
2024-08-14 12:26 ` [PATCH 4/5] ARM: dts: microchip: Rename the usb node Andrei Simion
2024-08-14 13:22 ` Krzysztof Kozlowski
2024-09-05 13:51 ` Andrei.Simion
2024-09-05 13:55 ` Krzysztof Kozlowski
2024-08-14 12:26 ` Andrei Simion [this message]
2024-08-14 13:23 ` [PATCH 5/5] ARM: dts: microchip: Rename LED sub nodes name Krzysztof Kozlowski
2024-08-15 7:57 ` Alexander Dahl
2024-08-15 7:57 ` Alexander Dahl
2024-08-16 8:52 ` Andrei.Simion
2024-08-16 9:06 ` Alexander Dahl
2024-08-16 9:06 ` Alexander Dahl
2024-08-20 6:32 ` Andrei.Simion
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240814122633.198562-6-andrei.simion@microchip.com \
--to=andrei.simion@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=cristian.birsan@microchip.com \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=peda@axentia.se \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.