[PATCH] dts: nxp: mxs: Add descriptions for imx287 based btt3-[012] devices

[Lukasz Majewski <lukma@denx.de>]

The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
some extend similar to already upstreamed XEA devices, hence are
using common imx28-lwe.dtsi file.

New, btt3.dtsi has been added to embrace common DTS properties for
different HW revisions for this device.

As a result - changes introduced in btt3-[012].dts are minimal.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
 arch/arm/boot/dts/nxp/mxs/Makefile   |   3 +
 arch/arm/boot/dts/nxp/mxs/btt3-0.dts |  12 +
 arch/arm/boot/dts/nxp/mxs/btt3-1.dts |   8 +
 arch/arm/boot/dts/nxp/mxs/btt3-2.dts |  12 +
 arch/arm/boot/dts/nxp/mxs/btt3.dtsi  | 320 +++++++++++++++++++++++++++
 5 files changed, 355 insertions(+)
 create mode 100644 arch/arm/boot/dts/nxp/mxs/btt3-0.dts
 create mode 100644 arch/arm/boot/dts/nxp/mxs/btt3-1.dts
 create mode 100644 arch/arm/boot/dts/nxp/mxs/btt3-2.dts
 create mode 100644 arch/arm/boot/dts/nxp/mxs/btt3.dtsi

diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile
index a430d04f9c69..fa50eae3f431 100644
--- a/arch/arm/boot/dts/nxp/mxs/Makefile
+++ b/arch/arm/boot/dts/nxp/mxs/Makefile
@@ -1,5 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MXS) += \
+	btt3-0.dtb \
+	btt3-1.dtb \
+	btt3-2.dtb \
 	imx23-evk.dtb \
 	imx23-olinuxino.dtb \
 	imx23-sansa.dtb \
diff --git a/arch/arm/boot/dts/nxp/mxs/btt3-0.dts b/arch/arm/boot/dts/nxp/mxs/btt3-0.dts
new file mode 100644
index 000000000000..0c782c3136f5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/btt3-0.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "btt3.dtsi"
+
+&hog_pins_rev {
+	fsl,pull-up = <MXS_PULL_ENABLE>;
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/btt3-1.dts b/arch/arm/boot/dts/nxp/mxs/btt3-1.dts
new file mode 100644
index 000000000000..031fb6e4c917
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/btt3-1.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "btt3.dtsi"
diff --git a/arch/arm/boot/dts/nxp/mxs/btt3-2.dts b/arch/arm/boot/dts/nxp/mxs/btt3-2.dts
new file mode 100644
index 000000000000..ec8315527c94
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/btt3-2.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "btt3.dtsi"
+
+&lcdif {
+	display = <&display_te_b>;
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/btt3.dtsi b/arch/arm/boot/dts/nxp/mxs/btt3.dtsi
new file mode 100644
index 000000000000..5574cebf9abc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/btt3.dtsi
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+/dts-v1/;
+#include "imx28-lwe.dtsi"
+
+/ {
+	model = "BTT3";
+
+	compatible = "lwn,btt3", "fsl,imx28";
+
+	chosen {
+	       bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1 quiet";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x10000000>;
+		device_type = "memory";
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 24 0>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "BTTC Audio";
+		simple-audio-card,widgets = "Speaker", "BTTC Speaker";
+		simple-audio-card,routing = "BTTC Speaker", "SPKOUTN", "BTTC Speaker", "SPKOUTP";
+		simple-audio-card,dai-link@0 {
+			format = "left_j";
+			bitclock-master = <&dai0_master>;
+			frame-master = <&dai0_master>;
+			mclk-fs = <256>;
+			dai0_master: cpu {
+				sound-dai = <&saif0>;
+			};
+			codec {
+				sound-dai = <&wm89xx>;
+				clocks = <&saif0>;
+			};
+		};
+	};
+
+	wifi_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_pin_bttc>;
+		reset-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		/* W1-163 needs 60us for WL_EN to be low and */
+		/* 150ms after high before downloading FW is possible */
+		post-power-on-delay-ms = <200>;
+		power-off-delay-us = <100>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&i2c0 {
+	wm89xx: codec@1a {
+		compatible = "wlf,wm8940", "wlf,wm8974";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a>, <&lcdif_sync_pins_bttc>,
+		    <&lcdif_reset_pins_bttc>;
+	lcd-supply = <&reg_3v3>;
+	display = <&display0>;
+	status = "okay";
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <6500000>;
+				hactive = <320>;
+				vactive = <240>;
+				hfront-porch = <20>;
+				hback-porch = <38>;
+				hsync-len = <30>;
+				vfront-porch = <4>;
+				vback-porch = <14>;
+				vsync-len = <4>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <0>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+	display_te_b: display1 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+		display-timings {
+			native-mode = <&timing0>;
+			timing_te_b: timing0 {
+				clock-frequency = <6500000>;
+				hactive = <320>;
+				vactive = <240>;
+				hfront-porch = <20>;
+				hback-porch = <68>;
+				hsync-len = <30>;
+				vfront-porch = <4>;
+				vback-porch = <14>;
+				vsync-len = <4>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+
+};
+
+&mac0 {
+	clocks = <&clks 57>, <&clks 57>, <&clks 64>;
+	clock-names = "ipg", "ahb", "enet_out";
+	phy-handle = <&mac0_phy>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_3v3>;
+	local-mac-address = [ 00 11 B8 00 BF 8A ];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mac0_phy: ethernet-phy@0 {
+			/* LAN8720Ai - PHY ID */
+			compatible = "ethernet-phy-id0007.c0f0","ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			smsc,disable-energy-detect;
+			max-speed = <100>;
+
+			reset-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* GPIO4_12 */
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>, <&hog_pins_rev>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY2__GPIO_0_22
+			MX28_PAD_GPMI_RDY3__GPIO_0_23
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_LCD_VSYNC__GPIO_1_28
+			MX28_PAD_SSP2_SS1__GPIO_2_20
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+			MX28_PAD_AUART2_CTS__GPIO_3_10
+			MX28_PAD_AUART2_RTS__GPIO_3_11
+			MX28_PAD_GPMI_WRN__GPIO_0_25
+			MX28_PAD_ENET0_RXD2__GPIO_4_9
+			MX28_PAD_ENET0_TXD2__GPIO_4_11
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_rev: hog@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_ENET0_RXD3__GPIO_4_10
+			MX28_PAD_ENET0_TX_CLK__GPIO_4_5
+			MX28_PAD_ENET0_COL__GPIO_4_14
+			MX28_PAD_ENET0_CRS__GPIO_4_15
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	keypad_pins_bttc: keypad-bttc@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_AUART0_CTS__GPIO_3_2
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D04__GPIO_0_4
+			MX28_PAD_GPMI_D05__GPIO_0_5
+			MX28_PAD_GPMI_D06__GPIO_0_6
+			MX28_PAD_GPMI_D07__GPIO_0_7
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_CE2N__GPIO_0_18
+			MX28_PAD_GPMI_CE3N__GPIO_0_19
+			MX28_PAD_GPMI_RDY0__GPIO_0_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_sync_pins_bttc: lcdif-bttc@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_ENABLE__LCD_ENABLE
+			MX28_PAD_LCD_HSYNC__LCD_HSYNC
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_reset_pins_bttc: lcdif-bttc@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	ssp1_sdio_pins_a: ssp1-sdio@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP1_DATA0__SSP1_D0
+			MX28_PAD_GPMI_D01__SSP1_D1
+			MX28_PAD_GPMI_D02__SSP1_D2
+			MX28_PAD_SSP1_DATA3__SSP1_D3
+			MX28_PAD_SSP1_CMD__SSP1_CMD
+			MX28_PAD_SSP1_SCK__SSP1_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	wifi_en_pin_bttc: wifi_en_pin@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a>;
+	status = "okay";
+};
+
+&reg_usb_5v {
+	gpio = <&gpio1 28 0>;
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&clks 53>;
+	assigned-clock-rates = <12000000>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&ssp1 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp1_sdio_pins_a>;
+	bus-width = <4>;
+	no-1-8-v;       /* force 3.3V VIO */
+	pm-ignore-notify;
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	keep-power-in-suspend;
+	status = "okay";
+
+	wlan@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
-- 
2.39.2