From: Andrei Simion <andrei.simion@microchip.com>
To: <nicolas.ferre@microchip.com>, <claudiu.beznea@tuxon.dev>,
<alexandre.belloni@bootlin.com>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
Andrei Simion <andrei.simion@microchip.com>
Subject: [PATCH] ARM: dts: microchip: sam9x60: Add missing property atmel,usart-mode
Date: Thu, 5 Sep 2024 12:30:46 +0300 [thread overview]
Message-ID: <20240905093046.23428-1-andrei.simion@microchip.com> (raw)
~: make dtbs_check DT_SCHEMA_FILES=atmel,at91-usart.ymal
-> for all boards which inherit sam9x60.dtsi: serial@200: $nodename:0:
'serial@200' does not match '^spi(@.*|-([0-9]|[1-9][0-9]+))?$
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
-> Means : atmel,usart-mode = <AT91_USART_MODE_SERIAL> misses for uart:
0,1,2,3,4,6,7,8,9,10,11,12
Add to uart nodes the property atmel,usart-mode to specify the driver to be
used in serial mode to be compliant to atmel,at91-usart.yaml.
Fixes: 99c808335877 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
---
arch/arm/boot/dts/microchip/sam9x60.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/sam9x60.dtsi b/arch/arm/boot/dts/microchip/sam9x60.dtsi
index 04a6d716ecaf..0ba424bba7cc 100644
--- a/arch/arm/boot/dts/microchip/sam9x60.dtsi
+++ b/arch/arm/boot/dts/microchip/sam9x60.dtsi
@@ -174,6 +174,7 @@ flx4: flexcom@f0000000 {
uart4: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -376,6 +377,7 @@ flx11: flexcom@f0020000 {
uart11: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -427,6 +429,7 @@ flx12: flexcom@f0024000 {
uart12: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -586,6 +589,7 @@ flx6: flexcom@f8010000 {
uart6: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -637,6 +641,7 @@ flx7: flexcom@f8014000 {
uart7: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -688,6 +693,7 @@ flx8: flexcom@f8018000 {
uart8: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -739,6 +745,7 @@ flx0: flexcom@f801c000 {
uart0: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -809,6 +816,7 @@ flx1: flexcom@f8020000 {
uart1: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -879,6 +887,7 @@ flx2: flexcom@f8024000 {
uart2: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -949,6 +958,7 @@ flx3: flexcom@f8028000 {
uart3: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -1074,6 +1084,7 @@ flx9: flexcom@f8040000 {
uart9: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
@@ -1125,6 +1136,7 @@ flx10: flexcom@f8044000 {
uart10: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
base-commit: fdadd93817f124fd0ea6ef251d4a1068b7feceba
--
2.34.1
next reply other threads:[~2024-09-05 9:33 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-09-05 9:30 Andrei Simion [this message]
2024-09-05 14:37 ` [PATCH] ARM: dts: microchip: sam9x60: Add missing property atmel,usart-mode Nicolas Ferre
2024-09-12 7:23 ` claudiu beznea
2024-09-12 7:35 ` Andrei.Simion
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240905093046.23428-1-andrei.simion@microchip.com \
--to=andrei.simion@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.