Re: [PATCH v12 3/3] PCI/ASPM: Make pci_save_aspm_l1ss_state save both child and parent's L1SS configuration

["Krzysztof Wilczyński" <kw@linux.com>]

Hello,

> PCI devices' parameters on the VMD bus have been programmed properly
> originally. But, cleared after pci_reset_bus() and have not been restored
> correctly. This leads the link's L1.2 between PCIe Root Port and child
> device gets wrong configs.
> 
> Here is a failed example on ASUS B1400CEAE with enabled VMD. Both PCIe
> bridge and NVMe device should have the same LTR1.2_Threshold value.
> However, they are configured as different values in this case:
> 
> 10000:e0:06.0 PCI bridge [0604]: Intel Corporation 11th Gen Core Processor PCIe Controller [8086:9a09] (rev 01) (prog-if 00 [Normal decode])
>   ...
>   Capabilities: [200 v1] L1 PM Substates
>     L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
>       PortCommonModeRestoreTime=45us PortTPowerOnTime=50us
>     L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
>       T_CommonMode=0us LTR1.2_Threshold=0ns
>     L1SubCtl2: T_PwrOn=0us
> 
> 10000:e1:00.0 Non-Volatile memory controller [0108]: Sandisk Corp WD Blue SN550 NVMe SSD [15b7:5009] (rev 01) (prog-if 02 [NVM Express])
>   ...
>   Capabilities: [900 v1] L1 PM Substates
>     L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
>       PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
>     L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
>       T_CommonMode=0us LTR1.2_Threshold=101376ns
>     L1SubCtl2: T_PwrOn=50us
> 
> Here is VMD mapped PCI device tree:
> 
> -+-[0000:00]-+-00.0  Intel Corporation Device 9a04
>  | ...
>  \-[10000:e0]-+-06.0-[e1]----00.0  Sandisk Corp WD Blue SN550 NVMe SSD
>               \-17.0  Intel Corporation Tiger Lake-LP SATA Controller
> 
> When pci_reset_bus() resets the bus [e1] of the NVMe, it only saves and
> restores NVMe's state before and after reset. Then, when it restores the
> NVMe's state, ASPM code restores L1SS for both the parent bridge and the
> NVMe in pci_restore_aspm_l1ss_state(). The NVMe's L1SS is restored
> correctly. But, the parent bridge's L1SS is restored with a wrong value 0x0
> because the parent bridge's L1SS wasn't saved by pci_save_aspm_l1ss_state()
> before reset.
> 
> So, if the PCI device has a parent, make pci_save_aspm_l1ss_state() save
> the parent's L1SS configuration, too. This is symmetric on
> pci_restore_aspm_l1ss_state().

Applied to aspm, thank you!

[01/02] PCI/ASPM: Add notes about enabling PCI-PM L1SS to pci_enable_link_state(_locked)
        https://git.kernel.org/pci/pci/c/4681da23786a

[02/02] PCI/ASPM: Make pci_save_aspm_l1ss_state save both child and parent's L1SS configuration
        https://git.kernel.org/pci/pci/c/1f37e72d586f

	Krzysztof