All of lore.kernel.org
 help / color / mirror / Atom feed
From: Christian Marangi <ansuelsmth@gmail.com>
To: Christian Marangi <ansuelsmth@gmail.com>,
	Andrew Lunn <andrew@lunn.ch>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Vladimir Oltean <olteanv@gmail.com>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	Russell King <linux@armlinux.org.uk>,
	Matthias Brugger <matthias.bgg@gmail.com>,
	AngeloGioacchino Del Regno
	<angelogioacchino.delregno@collabora.com>,
	linux-arm-kernel@lists.infradead.org,
	linux-mediatek@lists.infradead.org, netdev@vger.kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	upstream@airoha.com
Subject: [net-next PATCH v7 4/4] net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY
Date: Sun, 17 Nov 2024 14:27:59 +0100	[thread overview]
Message-ID: <20241117132811.67804-5-ansuelsmth@gmail.com> (raw)
In-Reply-To: <20241117132811.67804-1-ansuelsmth@gmail.com>

Add support for Airoha AN8855 Internal Switch Gigabit PHY.

This is a simple PHY driver to configure and calibrate the PHY for the
AN8855 Switch with the use of NVMEM cells.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS                  |   1 +
 drivers/net/phy/Kconfig      |   5 +
 drivers/net/phy/Makefile     |   1 +
 drivers/net/phy/air_an8855.c | 267 +++++++++++++++++++++++++++++++++++
 4 files changed, 274 insertions(+)
 create mode 100644 drivers/net/phy/air_an8855.c

diff --git a/MAINTAINERS b/MAINTAINERS
index e3077d9feee2..cf34add2a0bb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -726,6 +726,7 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855.yaml
 F:	drivers/net/dsa/an8855.c
 F:	drivers/net/dsa/an8855.h
+F:	drivers/net/phy/air_an8855.c
 
 AIROHA ETHERNET DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index ee3ea0b56d48..1d474038ea7f 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -79,6 +79,11 @@ config SFP
 
 comment "MII PHY device drivers"
 
+config AIR_AN8855_PHY
+	tristate "Airoha AN8855 Internal Gigabit PHY"
+	help
+	  Currently supports the internal Airoha AN8855 Switch PHY.
+
 config AIR_EN8811H_PHY
 	tristate "Airoha EN8811H 2.5 Gigabit PHY"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 90f886844381..baba7894785b 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -35,6 +35,7 @@ obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
 
 obj-$(CONFIG_ADIN_PHY)		+= adin.o
 obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
+obj-$(CONFIG_AIR_AN8855_PHY)   += air_an8855.o
 obj-$(CONFIG_AIR_EN8811H_PHY)   += air_en8811h.o
 obj-$(CONFIG_AMD_PHY)		+= amd.o
 obj-$(CONFIG_AMCC_QT2025_PHY)	+= qt2025.o
diff --git a/drivers/net/phy/air_an8855.c b/drivers/net/phy/air_an8855.c
new file mode 100644
index 000000000000..7ede6674994f
--- /dev/null
+++ b/drivers/net/phy/air_an8855.c
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Christian Marangi <ansuelsmth@gmail.com>
+ */
+
+#include <linux/phy.h>
+#include <linux/module.h>
+#include <linux/bitfield.h>
+#include <linux/nvmem-consumer.h>
+
+#define AN8855_PHY_SELECT_PAGE			0x1f
+#define   AN8855_PHY_PAGE			GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+
+/* MII Registers Page 1 */
+#define AN8855_PHY_EXT_REG_14			0x14
+#define   AN8855_PHY_EN_DOWN_SHIFT		BIT(4)
+
+/* R50 Calibration regs in MDIO_MMD_VEND1 */
+#define AN8855_PHY_R500HM_RSEL_TX_AB		0x174
+#define AN8855_PHY_R50OHM_RSEL_TX_A_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_A		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_B_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_B		GENMASK(6, 0)
+#define AN8855_PHY_R500HM_RSEL_TX_CD		0x175
+#define AN8855_PHY_R50OHM_RSEL_TX_C_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_C		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_D_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_D		GENMASK(6, 0)
+
+#define AN8855_SWITCH_EFUSE_R50O		GENMASK(30, 24)
+
+/* PHY TX PAIR DELAY SELECT Register */
+#define AN8855_PHY_TX_PAIR_DLY_SEL_GBE		0x013
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE GENMASK(14, 12)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_B_GBE GENMASK(10, 8)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE GENMASK(6, 4)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_D_GBE GENMASK(2, 0)
+/* PHY ADC Register */
+#define AN8855_PHY_RXADC_CTRL			0x0d8
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A	BIT(12)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_B	BIT(8)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C	BIT(4)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_D	BIT(0)
+#define AN8855_PHY_RXADC_REV_0			0x0d9
+#define   AN8855_PHY_RG_AD_RESERVE0_A		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_B		GENMASK(7, 0)
+#define AN8855_PHY_RXADC_REV_1			0x0da
+#define   AN8855_PHY_RG_AD_RESERVE0_C		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_D		GENMASK(7, 0)
+
+#define AN8855_PHY_ID				0xc0ff0410
+
+#define AN8855_PHY_FLAGS_EN_CALIBRATION		BIT(0)
+
+struct air_an8855_priv {
+	u8 calibration_data[4];
+};
+
+static const u8 dsa_r50ohm_table[] = {
+	127, 127, 127, 127, 127, 127, 127, 127, 127, 127,
+	127, 127, 127, 127, 127, 127, 127, 126, 122, 117,
+	112, 109, 104, 101,  97,  94,  90,  88,  84,  80,
+	78,  74,  72,  68,  66,  64,  61,  58,  56,  53,
+	51,  48,  47,  44,  42,  40,  38,  36,  34,  32,
+	31,  28,  27,  24,  24,  22,  20,  18,  16,  16,
+	14,  12,  11,   9
+};
+
+static int en8855_get_r50ohm_val(struct device *dev, const char *calib_name,
+				 u8 *dest)
+{
+	u32 shift_sel, val;
+	int ret;
+	int i;
+
+	ret = nvmem_cell_read_u32(dev, calib_name, &val);
+	if (ret)
+		return ret;
+
+	shift_sel = FIELD_GET(AN8855_SWITCH_EFUSE_R50O, val);
+	for (i = 0; i < ARRAY_SIZE(dsa_r50ohm_table); i++)
+		if (dsa_r50ohm_table[i] == shift_sel)
+			break;
+
+	if (i < 8 || i >= ARRAY_SIZE(dsa_r50ohm_table))
+		*dest = dsa_r50ohm_table[25];
+	else
+		*dest = dsa_r50ohm_table[i - 8];
+
+	return 0;
+}
+
+static int an8855_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct device_node *node = dev->of_node;
+	struct air_an8855_priv *priv;
+	int ret;
+
+	/* If we don't have a node, skip get calib */
+	if (!node)
+		return 0;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	ret = en8855_get_r50ohm_val(dev, "tx_a", &priv->calibration_data[0]);
+	if (ret)
+		return ret;
+
+	ret = en8855_get_r50ohm_val(dev, "tx_b", &priv->calibration_data[1]);
+	if (ret)
+		return ret;
+
+	ret = en8855_get_r50ohm_val(dev, "tx_c", &priv->calibration_data[2]);
+	if (ret)
+		return ret;
+
+	ret = en8855_get_r50ohm_val(dev, "tx_d", &priv->calibration_data[3]);
+	if (ret)
+		return ret;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int an8855_get_downshift(struct phy_device *phydev, u8 *data)
+{
+	int val;
+
+	val = phy_read_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1, AN8855_PHY_EXT_REG_14);
+	if (val < 0)
+		return val;
+
+	*data = val & AN8855_PHY_EN_DOWN_SHIFT ? DOWNSHIFT_DEV_DEFAULT_COUNT :
+						 DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int an8855_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	u16 ds = cnt != DOWNSHIFT_DEV_DISABLE ? AN8855_PHY_EN_DOWN_SHIFT : 0;
+
+	return phy_modify_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1,
+				AN8855_PHY_EXT_REG_14, AN8855_PHY_EN_DOWN_SHIFT,
+				ds);
+}
+
+static int an8855_config_init(struct phy_device *phydev)
+{
+	struct air_an8855_priv *priv = phydev->priv;
+	int ret;
+
+	/* Enable HW auto downshift */
+	ret = an8855_set_downshift(phydev, DOWNSHIFT_DEV_DEFAULT_COUNT);
+	if (ret)
+		return ret;
+
+	/* Apply calibration values, if needed.
+	 * AN8855_PHY_FLAGS_EN_CALIBRATION signal this.
+	 */
+	if (priv && phydev->dev_flags & AN8855_PHY_FLAGS_EN_CALIBRATION) {
+		u8 *calibration_data = priv->calibration_data;
+
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_AB,
+				     AN8855_PHY_R50OHM_RSEL_TX_A | AN8855_PHY_R50OHM_RSEL_TX_B,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_A, calibration_data[0]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_B, calibration_data[1]));
+		if (ret)
+			return ret;
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_CD,
+				     AN8855_PHY_R50OHM_RSEL_TX_C | AN8855_PHY_R50OHM_RSEL_TX_D,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_C, calibration_data[2]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_D, calibration_data[3]));
+		if (ret)
+			return ret;
+	}
+
+	/* Apply values to reduce signal noise */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_TX_PAIR_DLY_SEL_GBE,
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE, 0x4) |
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE, 0x4));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_CTRL,
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A |
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C);
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_0,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_A, 0x1));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_1,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_C, 0x1));
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int an8855_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_read_page(struct phy_device *phydev)
+{
+	return __phy_read(phydev, AN8855_PHY_SELECT_PAGE);
+}
+
+static int an8855_write_page(struct phy_device *phydev, int page)
+{
+	return __phy_write(phydev, AN8855_PHY_SELECT_PAGE, page);
+}
+
+static struct phy_driver an8855_driver[] = {
+{
+	PHY_ID_MATCH_EXACT(AN8855_PHY_ID),
+	.name			= "Airoha AN8855 internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.flags			= PHY_IS_INTERNAL,
+	.probe			= an8855_probe,
+	.config_init		= an8855_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_tunable		= an8855_get_tunable,
+	.set_tunable		= an8855_set_tunable,
+	.suspend		= genphy_suspend,
+	.resume			= genphy_resume,
+	.read_page		= an8855_read_page,
+	.write_page		= an8855_write_page,
+}, };
+
+module_phy_driver(an8855_driver);
+
+static struct mdio_device_id __maybe_unused an8855_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(AN8855_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, an8855_tbl);
+
+MODULE_DESCRIPTION("Airoha AN8855 PHY driver");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.45.2



  parent reply	other threads:[~2024-11-17 13:33 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-11-17 13:27 [net-next PATCH v7 0/4] net: dsa: Add Airoha AN8855 support Christian Marangi
2024-11-17 13:27 ` [net-next PATCH v7 1/4] net: dsa: add devm_dsa_register_switch() Christian Marangi
2024-11-17 13:27 ` [net-next PATCH v7 2/4] dt-bindings: net: dsa: Add Airoha AN8855 Gigabit Switch documentation Christian Marangi
2024-11-17 13:27 ` [net-next PATCH v7 3/4] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver Christian Marangi
2024-11-17 13:27 ` Christian Marangi [this message]
2024-11-18 14:48 ` [net-next PATCH v7 0/4] net: dsa: Add Airoha AN8855 support Vladimir Oltean
2024-11-18 18:35   ` Christian Marangi
2024-11-19 11:10     ` Paolo Abeni
2024-11-19 12:46       ` Christian Marangi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20241117132811.67804-5-ansuelsmth@gmail.com \
    --to=ansuelsmth@gmail.com \
    --cc=andrew@lunn.ch \
    --cc=angelogioacchino.delregno@collabora.com \
    --cc=conor+dt@kernel.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edumazet@google.com \
    --cc=f.fainelli@gmail.com \
    --cc=hkallweit1@gmail.com \
    --cc=krzk+dt@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=linux@armlinux.org.uk \
    --cc=matthias.bgg@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=pabeni@redhat.com \
    --cc=robh@kernel.org \
    --cc=upstream@airoha.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.