Re: [PATCH net-next v2 2/2] net: phy: dp83822: Add support for GPIO2 clock output

[Dimitri Fedrau <dima.fedrau@gmail.com>]

Am Wed, Dec 11, 2024 at 10:45:53AM +0100 schrieb Krzysztof Kozlowski:
> On Wed, Dec 11, 2024 at 09:04:40AM +0100, Dimitri Fedrau wrote:
> > The GPIO2 pin on the DP83822 can be configured as clock output. Add support
> > for configuration via DT.
> > 
> > Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
> > ---
> >  drivers/net/phy/dp83822.c | 40 ++++++++++++++++++++++++++++++++++++++++
> >  1 file changed, 40 insertions(+)
> > 
> > diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
> > index 25ee09c48027c86b7d8f4acb5cbe2e157c56a85a..dc5595eae6cc74e5c77914d53772c5fad64c3e70 100644
> > --- a/drivers/net/phy/dp83822.c
> > +++ b/drivers/net/phy/dp83822.c
> > @@ -14,6 +14,8 @@
> >  #include <linux/netdevice.h>
> >  #include <linux/bitfield.h>
> >  
> > +#include <dt-bindings/net/ti-dp83822.h>
> > +
> >  #define DP83822_PHY_ID	        0x2000a240
> >  #define DP83825S_PHY_ID		0x2000a140
> >  #define DP83825I_PHY_ID		0x2000a150
> > @@ -30,6 +32,7 @@
> >  #define MII_DP83822_FCSCR	0x14
> >  #define MII_DP83822_RCSR	0x17
> >  #define MII_DP83822_RESET_CTRL	0x1f
> > +#define MII_DP83822_IOCTRL2	0x463
> >  #define MII_DP83822_GENCFG	0x465
> >  #define MII_DP83822_SOR1	0x467
> >  
> > @@ -104,6 +107,11 @@
> >  #define DP83822_RX_CLK_SHIFT	BIT(12)
> >  #define DP83822_TX_CLK_SHIFT	BIT(11)
> >  
> > +/* IOCTRL2 bits */
> > +#define DP83822_IOCTRL2_GPIO2_CLK_SRC		GENMASK(6, 4)
> > +#define DP83822_IOCTRL2_GPIO2_CTRL		GENMASK(2, 0)
> > +#define DP83822_IOCTRL2_GPIO2_CTRL_CLK_REF	GENMASK(1, 0)
> > +
> >  /* SOR1 mode */
> >  #define DP83822_STRAP_MODE1	0
> >  #define DP83822_STRAP_MODE2	BIT(0)
> > @@ -139,6 +147,8 @@ struct dp83822_private {
> >  	u8 cfg_dac_minus;
> >  	u8 cfg_dac_plus;
> >  	struct ethtool_wolinfo wol;
> > +	bool set_gpio2_clk_out;
> > +	u32 gpio2_clk_out;
> >  };
> >  
> >  static int dp83822_config_wol(struct phy_device *phydev,
> > @@ -413,6 +423,15 @@ static int dp83822_config_init(struct phy_device *phydev)
> >  	int err = 0;
> >  	int bmcr;
> >  
> > +	if (dp83822->set_gpio2_clk_out)
> > +		phy_modify_mmd(phydev, MDIO_MMD_VEND2, MII_DP83822_IOCTRL2,
> > +			       DP83822_IOCTRL2_GPIO2_CTRL |
> > +			       DP83822_IOCTRL2_GPIO2_CLK_SRC,
> > +			       FIELD_PREP(DP83822_IOCTRL2_GPIO2_CTRL,
> > +					  DP83822_IOCTRL2_GPIO2_CTRL_CLK_REF) |
> > +			       FIELD_PREP(DP83822_IOCTRL2_GPIO2_CLK_SRC,
> > +					  dp83822->gpio2_clk_out));
> 
> You include the header but you do not use the defines, so it's a proof
> these are register values. Register values are not bindings, they do not
> bind anything. Bindings are imaginary numbers starting from 0 or 1 which
> are used between drivers and DTS, serving as abstraction layer (or
> abstraction values) between these two.
> 
> You do not have here abstraction. Drop the bindings header entirely.
>
Ok, thanks for the explanation.

Best regards,
Dimitri Fedrau