From: Markuss Broks <markuss.broks@gmail.com>
To: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Lorenzo Pieralisi <lpieralisi@kernel.org>,
Alim Akhtar <alim.akhtar@samsung.com>,
Sylwester Nawrocki <s.nawrocki@samsung.com>,
Linus Walleij <linus.walleij@linaro.org>,
Tomasz Figa <tomasz.figa@gmail.com>,
Will Deacon <will@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Krzysztof Kozlowski <krzk@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-gpio@vger.kernel.org,
Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>,
Markuss Broks <markuss.broks@gmail.com>,
Maksym Holovach <nergzd@nergzd723.xyz>
Subject: [PATCH RESEND v4 1/2] arm64: dts: exynos: Add Exynos9810 SoC support
Date: Sat, 14 Dec 2024 16:56:46 +0200 [thread overview]
Message-ID: <20241214-exynos9810-v4-1-4e91fbbc2133@gmail.com> (raw)
In-Reply-To: <20241214-exynos9810-v4-0-4e91fbbc2133@gmail.com>
Exynos 9810 is an ARMv8 mobile SoC found in various Samsung devices,
such as Samsung Galaxy S9 (starlte), S9 Plus (star2lte),
Note 9 (crownlte) and perhaps others.
Add minimal support for this SoC, including basic stuff like:
- PSCI for bringing up secondary cores
- ARMv8 generic timer
- GPIO and pinctrl.
The firmware coming with the devices based on this SoC is buggy
and doesn't configure CNTFRQ_EL0, as required by spec, so it's
needed to hardcode the frequency in the timer node.
Co-developed-by: Maksym Holovach <nergzd@nergzd723.xyz>
Signed-off-by: Maksym Holovach <nergzd@nergzd723.xyz>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
---
arch/arm64/boot/dts/exynos/exynos9810-pinctrl.dtsi | 503 +++++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos9810.dtsi | 273 +++++++++++
2 files changed, 776 insertions(+)
diff --git a/arch/arm64/boot/dts/exynos/exynos9810-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos9810-pinctrl.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..88091bf09e4e91b05801cafe956283984d564449
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos9810-pinctrl.dtsi
@@ -0,0 +1,503 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/*
+ * Samsung's Exynos 9810 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2024 Markuss Broks <markuss.broks@gmail.com>
+ * Copyright (c) 2024 Maksym Holovach <nergzd@nergzd723.xyz>
+ */
+
+#include "exynos-pinctrl.h"
+
+&pinctrl_alive {
+ etc1: etc1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa0: gpa0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa1: gpa1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa2: gpa2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa3: gpa3-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa4: gpa4-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpq0: gpq0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_aud {
+ gpb0: gpb0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb1: gpb1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb2: gpb2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_chub {
+ gph0: gph0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gph1: gph1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_cmgp {
+ gpm0: gpm0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm1: gpm1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm2: gpm2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm3: gpm3-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm4: gpm4-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm5: gpm5-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm6: gpm6-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm7: gpm7-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm10: gpm10-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm11: gpm11-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm12: gpm12-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm13: gpm13-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm14: gpm14-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm15: gpm15-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm16: gpm16-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm17: gpm17-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm40: gpm40-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm41: gpm41-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm42: gpm42-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpm43: gpm43-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&pinctrl_fsys0 {
+ gpf0: gpf0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_fsys1 {
+ gpf1: gpf1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf2: gpf2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_peric0 {
+ gpg0: gpg0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg1: gpg1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg2: gpg2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp0: gpp0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp1: gpp1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp2: gpp2-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp3: gpp3-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_peric1 {
+ gpc0: gpc0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc1: gpc1-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd0: gpd0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg3: gpg3-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp4: gpp4-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp5: gpp5-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp6: gpp6-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_vts {
+ gpt0: gpt0-gpio-bank {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos9810.dtsi b/arch/arm64/boot/dts/exynos/exynos9810.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..70b67b2574d5b66eb5fa421a87dd6f4e49f8f54e
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos9810.dtsi
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/*
+ * Samsung Exynos 9810 SoC device tree source
+ *
+ * Copyright (c) 2024 Markuss Broks <markuss.broks@gmail.com>
+ * Copyright (c) 2024 Maksym Holovach <nergzd@nergzd723.xyz>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "samsung,exynos9810";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ interrupt-parent = <&gic>;
+
+ aliases {
+ pinctrl0 = &pinctrl_alive;
+ pinctrl1 = &pinctrl_aud;
+ pinctrl2 = &pinctrl_chub;
+ pinctrl3 = &pinctrl_cmgp;
+ pinctrl4 = &pinctrl_fsys0;
+ pinctrl5 = &pinctrl_fsys1;
+ pinctrl6 = &pinctrl_peric0;
+ pinctrl7 = &pinctrl_peric1;
+ pinctrl8 = &pinctrl_vts;
+ };
+
+ arm-a55-pmu {
+ compatible = "arm,cortex-a55-pmu";
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ mongoose-m3-pmu {
+ compatible = "samsung,mongoose-pmu";
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu4>,
+ <&cpu5>,
+ <&cpu6>,
+ <&cpu7>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+ core1 {
+ cpu = <&cpu5>;
+ };
+ core2 {
+ cpu = <&cpu6>;
+ };
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x3>;
+ enable-method = "psci";
+ };
+
+ cpu4: cpu@100 {
+ device_type = "cpu";
+ compatible = "samsung,mongoose-m3";
+ reg = <0x100>;
+ enable-method = "psci";
+ };
+
+ cpu5: cpu@101 {
+ device_type = "cpu";
+ compatible = "samsung,mongoose-m3";
+ reg = <0x101>;
+ enable-method = "psci";
+ };
+
+ cpu6: cpu@102 {
+ device_type = "cpu";
+ compatible = "samsung,mongoose-m3";
+ reg = <0x102>;
+ enable-method = "psci";
+ };
+
+ cpu7: cpu@103 {
+ device_type = "cpu";
+ compatible = "samsung,mongoose-m3";
+ reg = <0x103>;
+ enable-method = "psci";
+ };
+ };
+
+ oscclk: osc-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-output-names = "oscclk";
+ };
+
+ psci {
+ compatible = "arm,psci";
+ method = "smc";
+ cpu_off = <0x84000002>;
+ cpu_on = <0xc4000003>;
+ cpu_suspend = <0xc4000001>;
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ ranges = <0x0 0x0 0x0 0x20000000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chipid@10000000 {
+ compatible = "samsung,exynos9810-chipid",
+ "samsung,exynos850-chipid";
+ reg = <0x10000000 0x100>;
+ };
+
+ gic: interrupt-controller@10101000 {
+ compatible = "arm,gic-400";
+ reg = <0x10101000 0x1000>,
+ <0x10102000 0x1000>,
+ <0x10104000 0x2000>,
+ <0x10106000 0x2000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ #address-cells = <0>;
+ #size-cells = <1>;
+ };
+
+ pinctrl_peric0: pinctrl@10430000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x10430000 0x1000>;
+ interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_peric1: pinctrl@10830000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x10830000 0x1000>;
+ interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_fsys0: pinctrl@11050000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x11050000 0x1000>;
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_fsys1: pinctrl@11430000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x11430000 0x1000>;
+ interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_vts: pinctrl@13880000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x13880000 0x1000>;
+ };
+
+ pinctrl_chub: pinctrl@13a80000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x13a80000 0x1000>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_alive: pinctrl@14050000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x14050000 0x1000>;
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos9810-wakeup-eint",
+ "samsung,exynos850-wakeup-eint",
+ "samsung,exynos7-wakeup-eint";
+ };
+ };
+
+ pmu_system_controller: system-controller@14060000 {
+ compatible = "samsung,exynos9810-pmu",
+ "samsung,exynos7-pmu", "syscon";
+ reg = <0x14060000 0x10000>;
+ };
+
+ pinctrl_cmgp: pinctrl@14220000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x14220000 0x1000>;
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos9810-wakeup-eint",
+ "samsung,exynos850-wakeup-eint",
+ "samsung,exynos7-wakeup-eint";
+ };
+ };
+
+ pinctrl_aud: pinctrl@17c60000 {
+ compatible = "samsung,exynos9810-pinctrl";
+ reg = <0x17c60000 0x1000>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ /* Hypervisor Virtual Timer interrupt is not wired to GIC */
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ /*
+ * Non-updatable, broken stock Samsung bootloader does not
+ * configure CNTFRQ_EL0
+ */
+ clock-frequency = <26000000>;
+ };
+};
+
+#include "exynos9810-pinctrl.dtsi"
+#include "arm/samsung/exynos-syscon-restart.dtsi"
--
2.47.0
next prev parent reply other threads:[~2024-12-14 14:59 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-12-14 14:56 [PATCH RESEND v4 0/2] Add support for Exynos9810 SoC and Samsung Galaxy S9 (SM-G960F) Markuss Broks
2024-12-14 14:56 ` Markuss Broks [this message]
2024-12-22 14:46 ` [PATCH RESEND v4 1/2] arm64: dts: exynos: Add Exynos9810 SoC support Krzysztof Kozlowski
2024-12-14 14:56 ` [PATCH RESEND v4 2/2] arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F) Markuss Broks
2024-12-22 14:47 ` [PATCH RESEND v4 0/2] Add support for Exynos9810 SoC and " Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241214-exynos9810-v4-1-4e91fbbc2133@gmail.com \
--to=markuss.broks@gmail.com \
--cc=alim.akhtar@samsung.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=ivo.ivanov.ivanov1@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=krzk@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=lpieralisi@kernel.org \
--cc=mark.rutland@arm.com \
--cc=nergzd@nergzd723.xyz \
--cc=robh@kernel.org \
--cc=s.nawrocki@samsung.com \
--cc=tomasz.figa@gmail.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.