Re: [PATCH v9] leds: Add LED1202 I2C driver

[Lee Jones <lee@kernel.org>]

What's going on with the subject line format?  Are you editing those
manually?  If so, please stop.  `git format-patch` should create those
for you.

> The output current can be adjusted separately for each channel by 8-bit
> analog (current sink input) and 12-bit digital (PWM) dimming control. The
> LED1202 implements 12 low-side current generators with independent dimming
> control.
> Internal volatile memory allows the user to store up to 8 different patterns,
> each pattern is a particular output configuration in terms of PWM
> duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
> common to all patterns. Each device tree LED node will have a corresponding
> entry in /sys/class/leds with the label name. The brightness property
> corresponds to the per channel analog dimming, while the patterns[1-8] to the
> PWM dimming control.
> 
> Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
> ---
> Changes in v9:
>   - log errors directly in st1202_write_reg and st1202_read_reg
>   - use mutex guards instead of lock/unlock
>   - remove i2c_set_clientdata
> Changes in v7:
>   - fix st1202_brightness_get() error: uninitialized symbol 'value'
> Changes in v6:
>   - fix build error
> Changes in v5:
>   - remove unused macros
>   - switch to using devm_led_classdev_register_ext (struct st1202_led update)
>   - add prescalar_to_milliseconds (convert [22..5660]ms to [0..255] reg value)
>   - remove register range check in dt_init (range protected by yaml)
>   - address all review comments in v4
> Changes in v4:
>   - Remove attributes/extended attributes implementation
>   - Use /sys/class/leds/<led>/hw_pattern (Pavel suggestion)
>   - Implement review findings of Christophe JAILLET
> Changes in v3:
>   - Rename all ll1202 to st1202, including driver file name
>   - Convert all magic numbers to defines
>   - Refactor the show/store callbacks as per Lee's and Thomas's review
>   - Remove ll1202_get_channel and use dev_ext_attributes instead
>   - Log all error values for all the functions
>   - Use sysfs_emit for show callbacks
> Changes in v2:
>   - Fix build error for device_attribute modes
>  drivers/leds/Kconfig       |  11 +
>  drivers/leds/Makefile      |   1 +
>  drivers/leds/leds-st1202.c | 431 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 443 insertions(+)
>  create mode 100644 drivers/leds/leds-st1202.c
> 
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index b784bb74a837..c4fdacc00066 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -931,6 +931,17 @@ config LEDS_LM36274
>  	  Say Y to enable the LM36274 LED driver for TI LMU devices.
>  	  This supports the LED device LM36274.
>  
> +config LEDS_ST1202
> +	tristate "LED Support for STMicroelectronics LED1202 I2C chips"
> +	depends on LEDS_CLASS
> +	depends on I2C
> +	depends on OF
> +	select LEDS_TRIGGERS
> +	help
> +	  Say Y to enable support for LEDs connected to LED1202
> +	  LED driver chips accessed via the I2C bus.
> +	  Supported devices include LED1202.

This last line is unnecessary.

>  config LEDS_TPS6105X
>  	tristate "LED support for TI TPS6105X"
>  	depends on LEDS_CLASS
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index 18afbb5a23ee..e8b39ef760cc 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -81,6 +81,7 @@ obj-$(CONFIG_LEDS_POWERNV)		+= leds-powernv.o
>  obj-$(CONFIG_LEDS_PWM)			+= leds-pwm.o
>  obj-$(CONFIG_LEDS_REGULATOR)		+= leds-regulator.o
>  obj-$(CONFIG_LEDS_SC27XX_BLTC)		+= leds-sc27xx-bltc.o
> +obj-$(CONFIG_LEDS_ST1202)		+= leds-st1202.o
>  obj-$(CONFIG_LEDS_SUN50I_A100)		+= leds-sun50i-a100.o
>  obj-$(CONFIG_LEDS_SUNFIRE)		+= leds-sunfire.o
>  obj-$(CONFIG_LEDS_SYSCON)		+= leds-syscon.o
> diff --git a/drivers/leds/leds-st1202.c b/drivers/leds/leds-st1202.c
> new file mode 100644
> index 000000000000..963e2b11758f
> --- /dev/null
> +++ b/drivers/leds/leds-st1202.c
> @@ -0,0 +1,431 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * LED driver for STMicroelectronics LED1202 chip
> + *
> + * Copyright (C) 2024 Remote-Tech Ltd. UK
> + */
> +
> +#include <linux/cleanup.h>
> +#include <linux/ctype.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/leds.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/string.h>
> +
> +#define ST1202_CHAN_DISABLE_ALL            0x00
> +#define ST1202_CHAN_ENABLE_HIGH            0x03
> +#define ST1202_CHAN_ENABLE_LOW             0x02
> +#define ST1202_CONFIG_REG                  0x04
> +/* PATS: Pattern sequence feature enable */
> +#define ST1202_CONFIG_REG_PATS             BIT(7)
> +/* PATSR: Pattern sequence runs (self-clear when sequence is finished) */
> +#define ST1202_CONFIG_REG_PATSR            BIT(6)
> +#define ST1202_CONFIG_REG_SHFT             BIT(3)
> +#define ST1202_DEV_ENABLE                  0x01
> +#define ST1202_DEV_ENABLE_ON               BIT(0)
> +#define ST1202_DEV_ENABLE_RESET            BIT(7)
> +#define ST1202_DEVICE_ID                   0x00
> +#define ST1202_ILED_REG0                   0x09
> +#define ST1202_MAX_LEDS                    12
> +#define ST1202_MAX_PATTERNS                8
> +#define ST1202_MILLIS_PATTERN_DUR_MAX      5660
> +#define ST1202_MILLIS_PATTERN_DUR_MIN      22
> +#define ST1202_PATTERN_DUR                 0x16
> +#define ST1202_PATTERN_PWM                 0x1E
> +#define ST1202_PATTERN_REP                 0x15
> +
> +struct st1202_led {
> +	struct fwnode_handle *fwnode;
> +	struct led_classdev led_cdev;
> +	struct st1202_chip *chip;
> +	bool is_active;
> +	int led_num;
> +};
> +
> +struct st1202_chip {
> +	struct i2c_client *client;
> +	struct mutex lock;
> +	struct st1202_led leds[ST1202_MAX_LEDS];
> +};
> +
> +static struct st1202_led *cdev_to_st1202_led(struct led_classdev *cdev)
> +{
> +	return container_of(cdev, struct st1202_led, led_cdev);
> +}
> +
> +static int st1202_read_reg(struct st1202_chip *chip, int reg, uint8_t *val)
> +{
> +	struct device *dev;
> +	int ret;
> +
> +	dev = &chip->client->dev;

This should go on the declaration line.

> +	ret = i2c_smbus_read_byte_data(chip->client, reg);
> +	if (ret < 0) {
> +		dev_err(&chip->client->dev, "Reading register [0x%x] failed, error: %d\n",
> +				reg, ret);

This would save the line wrap:

  "Failed to read register [0x%x]: %d\n"

> +		return ret;
> +	}
> +
> +	*val = (uint8_t)ret;
> +	return 0;
> +}
> +
> +static int st1202_write_reg(struct st1202_chip *chip, int reg, uint8_t val)
> +{
> +	struct device *dev;
> +	int ret;
> +
> +	dev = &chip->client->dev;

As above.

> +	ret = i2c_smbus_write_byte_data(chip->client, reg, val);
> +	if (ret != 0)
> +		dev_err(dev, "Failed writing value %d to register [0x%x], error: %d\n",
> +				val, reg, ret);

As above.

> +
> +	return ret;
> +}
> +
> +static uint8_t st1202_prescalar_to_miliseconds(unsigned int value)
> +{
> +	return value/ST1202_MILLIS_PATTERN_DUR_MIN - 1;

Doesn't scripts/checkpatch.pl warn about this?

Spaces around the '/'.

> +}
> +
> +static int st1202_pwm_pattern_write(struct st1202_chip *chip, int led_num,
> +				int pattern, unsigned int value)
> +{
> +	u8 value_l, value_h;
> +	int ret;
> +
> +	value_l = (u8)value;
> +	value_h = (u8)(value >> 8);
> +
> +	/*
> +	 *  Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
> +	 *  where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
> +	 *  and y is the pattern number in hexadecimal (y = 00h .. 07h)
> +	 */
> +	ret = st1202_write_reg(chip, (ST1202_PATTERN_PWM + (led_num * 2) + 0x18 * pattern),
> +				value_l);
> +	if (ret != 0)
> +		return ret;
> +
> +	/*
> +	 * Datasheet: Register address high = 1Eh + 01h + 2(xh) +18h*(yh),
> +	 * where x is the channel number in hexadecimal (x = 00h .. 0Bh)
> +	 * and y is the pattern number in hexadecimal (y = 00h .. 07h)
> +	 */
> +	ret = st1202_write_reg(chip, (ST1202_PATTERN_PWM + 0x1 + (led_num * 2) + 0x18 * pattern),
> +				value_h);
> +	if (ret != 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int st1202_duration_pattern_write(struct st1202_chip *chip, int pattern,
> +					unsigned int value)
> +{
> +	return st1202_write_reg(chip, (ST1202_PATTERN_DUR + pattern),
> +				st1202_prescalar_to_miliseconds(value));
> +}
> +
> +static void st1202_brightness_set(struct led_classdev *led_cdev,
> +				enum led_brightness value)
> +{
> +	struct st1202_led *led;
> +	struct st1202_chip *chip;
> +
> +	led = cdev_to_st1202_led(led_cdev);
> +	chip = led->chip;

Move these to the lines above.

> +	guard(mutex)(&chip->lock);

'\n'

> +	st1202_write_reg(chip, ST1202_ILED_REG0 + led->led_num, value);
> +}
> +
> +static enum led_brightness st1202_brightness_get(struct led_classdev *led_cdev)
> +{
> +	struct st1202_led *led;
> +	struct st1202_chip *chip;
> +	u8 value = 0;
> +
> +	led = cdev_to_st1202_led(led_cdev);
> +	chip = led->chip;

As above.

And everywhere else that this happens.

> +	guard(mutex)(&chip->lock);

'\n'

> +	st1202_read_reg(chip, ST1202_ILED_REG0 + led->led_num, &value);

'\n'

> +	return value;
> +}
> +
> +static int st1202_channel_set(struct st1202_chip *chip, int led_num, bool active)
> +{
> +	u8 chan_low, chan_high;
> +	int ret;
> +
> +	guard(mutex)(&chip->lock);
> +
> +	if (led_num <= 7) {
> +		ret = st1202_read_reg(chip, ST1202_CHAN_ENABLE_LOW, &chan_low);
> +		if (ret < 0)
> +			return ret;
> +
> +		chan_low = active ? chan_low | BIT(led_num) : chan_low & ~BIT(led_num);
> +
> +		ret = st1202_write_reg(chip, ST1202_CHAN_ENABLE_LOW, chan_low);
> +		if (ret < 0)
> +			return ret;
> +
> +	} else {
> +		ret = st1202_read_reg(chip, ST1202_CHAN_ENABLE_HIGH, &chan_high);
> +		if (ret < 0)
> +			return ret;
> +
> +		chan_high = active ? chan_high | (BIT(led_num) >> 8) :
> +					chan_high & ~(BIT(led_num) >> 8);
> +
> +		ret = st1202_write_reg(chip, ST1202_CHAN_ENABLE_HIGH, chan_high);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int st1202_led_set(struct led_classdev *ldev, enum led_brightness value)
> +{
> +	struct st1202_led *led;
> +	struct st1202_chip *chip;
> +
> +	led = cdev_to_st1202_led(ldev);
> +	chip = led->chip;
> +
> +	return st1202_channel_set(chip, led->led_num, value == LED_OFF ? false : true);
> +}
> +
> +static int st1202_led_pattern_clear(struct led_classdev *ldev)
> +{
> +	struct st1202_led *led;
> +	struct st1202_chip *chip;
> +	int ret;
> +
> +	led = cdev_to_st1202_led(ldev);
> +	chip = led->chip;
> +
> +	guard(mutex)(&chip->lock);
> +
> +	for (int patt = 0; patt < ST1202_MAX_PATTERNS; patt++) {
> +		ret = st1202_pwm_pattern_write(chip, led->led_num, patt, LED_OFF);
> +		if (ret != 0)
> +			return ret;
> +
> +		ret = st1202_duration_pattern_write(chip, patt, ST1202_MILLIS_PATTERN_DUR_MIN);
> +		if (ret != 0)
> +			return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int st1202_led_pattern_set(struct led_classdev *ldev,
> +				struct led_pattern *pattern,
> +				u32 len, int repeat)
> +{
> +	struct st1202_led *led;
> +	struct st1202_chip *chip;
> +	int ret;
> +
> +	led = cdev_to_st1202_led(ldev);
> +	chip = led->chip;
> +
> +	if (len > ST1202_MAX_PATTERNS)
> +		return -EINVAL;
> +
> +	guard(mutex)(&chip->lock);
> +
> +	for (int patt = 0; patt < len; patt++) {
> +		if (pattern[patt].delta_t < ST1202_MILLIS_PATTERN_DUR_MIN ||
> +				pattern[patt].delta_t > ST1202_MILLIS_PATTERN_DUR_MAX)
> +			return -EINVAL;
> +
> +		ret = st1202_pwm_pattern_write(chip, led->led_num, patt, pattern[patt].brightness);
> +		if (ret != 0)
> +			return ret;
> +
> +		ret = st1202_duration_pattern_write(chip, patt, pattern[patt].delta_t);
> +		if (ret != 0)
> +			return ret;
> +	}
> +
> +	ret = st1202_write_reg(chip, ST1202_PATTERN_REP, repeat);
> +	if (ret != 0)
> +		return ret;
> +
> +	ret = st1202_write_reg(chip, ST1202_CONFIG_REG, (ST1202_CONFIG_REG_PATSR |
> +				ST1202_CONFIG_REG_PATS | ST1202_CONFIG_REG_SHFT));
> +	if (ret != 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int st1202_dt_init(struct st1202_chip *chip)
> +{
> +	struct device *dev = &chip->client->dev;
> +	struct st1202_led *led;
> +	int err, reg;
> +
> +	for_each_available_child_of_node_scoped(dev_of_node(dev), child) {
> +		struct led_init_data init_data = {};
> +
> +		err = of_property_read_u32(child, "reg", &reg);
> +		if (err)
> +			return dev_err_probe(dev, err, "Invalid register\n");
> +
> +		led = &chip->leds[reg];
> +		led->is_active = true;
> +		led->fwnode = of_fwnode_handle(child);
> +
> +		led->led_cdev.max_brightness = U8_MAX;
> +		led->led_cdev.brightness_set_blocking = st1202_led_set;
> +		led->led_cdev.pattern_set = st1202_led_pattern_set;
> +		led->led_cdev.pattern_clear = st1202_led_pattern_clear;
> +		led->led_cdev.default_trigger = "pattern";
> +
> +		init_data.fwnode = led->fwnode;
> +		init_data.devicename = "st1202";
> +		init_data.default_label = ":";

'\n'

> +		err = devm_led_classdev_register_ext(dev, &led->led_cdev, &init_data);
> +		if (err < 0)
> +			return dev_err_probe(dev, err, "Failed to register LED class device\n");
> +
> +		led->led_cdev.brightness_set = st1202_brightness_set;
> +		led->led_cdev.brightness_get = st1202_brightness_get;
> +	}
> +
> +	return 0;
> +}
> +
> +static int st1202_setup(struct st1202_chip *chip)
> +{
> +	int ret;
> +
> +	guard(mutex)(&chip->lock);

'\n'

> +	/*
> +	 * Once the supply voltage is applied, the LED1202 executes some internal checks,
> +	 * afterwords it stops the oscillator and puts the internal LDO in quiescent mode.
> +	 * To start the device, EN bit must be set inside the “Device Enable” register at
> +	 * address 01h. As soon as EN is set, the LED1202 loads the adjustment parameters
> +	 * from the internal non-volatile memory and performs an auto-calibration procedure
> +	 * in order to increase the output current precision.
> +	 * Such initialization lasts about 6.5 ms.
> +	 */
> +
> +	/* Reset the chip during setup */
> +	ret = st1202_write_reg(chip, ST1202_DEV_ENABLE, ST1202_DEV_ENABLE_RESET);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Enable phase-shift delay feature */
> +	ret = st1202_write_reg(chip, ST1202_CONFIG_REG, ST1202_CONFIG_REG_SHFT);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Enable the device */
> +	ret = st1202_write_reg(chip, ST1202_DEV_ENABLE, ST1202_DEV_ENABLE_ON);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Duration of initialization */
> +	usleep_range(6500, 10000);
> +
> +	/* Deactivate all LEDS (channels) and activate only the ones found in Device Tree */
> +	ret = st1202_write_reg(chip, ST1202_CHAN_ENABLE_LOW, ST1202_CHAN_DISABLE_ALL);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = st1202_write_reg(chip, ST1202_CHAN_ENABLE_HIGH, ST1202_CHAN_DISABLE_ALL);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = st1202_write_reg(chip, ST1202_CONFIG_REG,
> +				ST1202_CONFIG_REG_PATS | ST1202_CONFIG_REG_PATSR);
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int st1202_probe(struct i2c_client *client)
> +{
> +	struct st1202_chip *chip;
> +	struct st1202_led *led;
> +	int ret;
> +
> +	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> +		return dev_err_probe(&client->dev, -EIO, "SMBUS Byte Data not Supported\n");
> +
> +	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
> +	if (!chip)
> +		return -ENOMEM;
> +
> +	devm_mutex_init(&client->dev, &chip->lock);
> +	chip->client = client;
> +
> +	ret = st1202_dt_init(chip);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = st1202_setup(chip);
> +	if (ret < 0)
> +		return ret;
> +
> +	for (int i = 0; i < ST1202_MAX_LEDS; i++) {
> +		led = &chip->leds[i];
> +		led->chip = chip;
> +		led->led_num = i;
> +
> +		if (led->is_active) {

if (!led->is_active)
	continue;

Then you can pull these back:

> +			ret = st1202_channel_set(led->chip, led->led_num, true);
> +			if (ret < 0)
> +				return dev_err_probe(&client->dev, ret,
> +						"Failed to activate LED channel\n");
> +
> +			ret = st1202_led_pattern_clear(&led->led_cdev);
> +			if (ret < 0)
> +				return dev_err_probe(&client->dev, ret,
> +						"Failed to clear LED pattern\n");
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct i2c_device_id st1202_id[] = {
> +	{ "st1202-i2c" },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(i2c, st1202_id);
> +
> +static const struct of_device_id st1202_dt_ids[] = {
> +	{ .compatible = "st,led1202" },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, st1202_dt_ids);
> +
> +static struct i2c_driver st1202_driver = {
> +	.driver = {
> +		.name = "leds-st1202",
> +		.of_match_table = of_match_ptr(st1202_dt_ids),
> +	},
> +	.probe = st1202_probe,
> +	.id_table = st1202_id,
> +};
> +module_i2c_driver(st1202_driver);
> +
> +MODULE_AUTHOR("Remote Tech LTD");
> +MODULE_DESCRIPTION("STMicroelectronics LED1202 : 12-channel constant current LED driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.39.3 (Apple Git-145)
> 
> 

-- 
Lee Jones [李琼斯]