Re: [PATCH net-next v3 1/4] net: stmmac: Switch to zero-copy in non-XDP RX path

[Furong Xu <0x1207@gmail.com>]

Hi Ido

On Sat, 25 Jan 2025 12:20:38 +0200, Ido Schimmel wrote:

> On Fri, Jan 24, 2025 at 10:42:56AM +0800, Furong Xu wrote:
> > On Thu, 23 Jan 2025 22:48:42 +0100, Andrew Lunn <andrew@lunn.ch>
> > wrote: 
> > > > Just to clarify, the patch that you had us try was not intended
> > > > as an actual fix, correct? It was only for diagnostic purposes,
> > > > i.e. to see if there is some kind of cache coherence issue,
> > > > which seems to be the case?  So perhaps the only fix needed is
> > > > to add dma-coherent to our device tree?    
> > > 
> > > That sounds quite error prone. How many other DT blobs are
> > > missing the property? If the memory should be coherent, i would
> > > expect the driver to allocate coherent memory. Or the driver
> > > needs to handle non-coherent memory and add the necessary
> > > flush/invalidates etc.  
> > 
> > stmmac driver does the necessary cache flush/invalidates to
> > maintain cache lines explicitly.  
> 
> Given the problem happens when the kernel performs syncing, is it
> possible that there is a problem with how the syncing is performed?
> 
> I am not familiar with this driver, but it seems to allocate multiple
> buffers per packet when split header is enabled and these buffers are
> allocated from the same page pool (see stmmac_init_rx_buffers()).
> Despite that, the driver is creating the page pool with a non-zero
> offset (see __alloc_dma_rx_desc_resources()) to avoid syncing the
> headroom, which is only present in the head buffer.
> 
> I asked Thierry to test the following patch [1] and initial testing
> seems OK. He also confirmed that "SPH feature enabled" shows up in the
> kernel log.
> BTW, the commit that added split header support (67afd6d1cfdf0) says
> that it "reduces CPU usage because without the feature all the entire
> packet is memcpy'ed, while that with the feature only the header is".
> This is no longer correct after your patch, so is there still value in
> the split header feature? With two large buffers being allocated from

Thanks for these great insights!

Yes, when "SPH feature enabled", it is not correct after my patch,
pp_params.offset should be updated to match the offset of split payload.

But I would like to let pp_params.max_len remains to
dma_conf->dma_buf_sz since the sizes of both header and payload are
limited to dma_conf->dma_buf_sz by DMA engine, no more than
dma_conf->dma_buf_sz bytes will be written into a page buffer.
So my patch would be like [2]:

BTW, the split header feature will be very useful on some certain
cases, stmmac driver should support this feature always.

[2]
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index edbf8994455d..def0d893efbb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -2091,7 +2091,7 @@ static int __alloc_dma_rx_desc_resources(struct stmmac_priv *priv,
        pp_params.nid = dev_to_node(priv->device);
        pp_params.dev = priv->device;
        pp_params.dma_dir = xdp_prog ? DMA_BIDIRECTIONAL : DMA_FROM_DEVICE;
-       pp_params.offset = stmmac_rx_offset(priv);
+       pp_params.offset = priv->sph ? 0 : stmmac_rx_offset(priv);
        pp_params.max_len = dma_conf->dma_buf_sz;

        rx_q->page_pool = page_pool_create(&pp_params);