All of lore.kernel.org
 help / color / mirror / Atom feed
From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>,
	Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>,
	Mark Brown <broonie@kernel.org>, Sasha Levin <sashal@kernel.org>,
	lgirdwood@gmail.com, perex@perex.cz, tiwai@suse.com,
	prabhakar.mahadev-lad.rj@bp.renesas.com,
	linux-sound@vger.kernel.org
Subject: [PATCH AUTOSEL 6.1 03/12] ASoC: rsnd: adjust convert rate limitation
Date: Mon, 24 Feb 2025 06:19:51 -0500	[thread overview]
Message-ID: <20250224112002.2214613-3-sashal@kernel.org> (raw)
In-Reply-To: <20250224112002.2214613-1-sashal@kernel.org>

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

[ Upstream commit 89f9cf185885d4358aa92b48e51d0f09b71775aa ]

Current rsnd driver supports Synchronous SRC Mode, but HW allow to update
rate only within 1% from current rate. Adjust to it.

Becially, this feature is used to fine-tune subtle difference that occur
during sampling rate conversion in SRC. So, it should be called within 1%
margin of rate difference.

If there was difference over 1%, it will apply with 1% increments by using
loop without indicating error message.

Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/871pwd2qe8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/sh/rcar/src.c | 98 ++++++++++++++++++++++++++++++++---------
 1 file changed, 76 insertions(+), 22 deletions(-)

diff --git a/sound/soc/sh/rcar/src.c b/sound/soc/sh/rcar/src.c
index 9893839666d7b..e985681363e25 100644
--- a/sound/soc/sh/rcar/src.c
+++ b/sound/soc/sh/rcar/src.c
@@ -34,6 +34,7 @@ struct rsnd_src {
 	struct rsnd_mod *dma;
 	struct rsnd_kctrl_cfg_s sen;  /* sync convert enable */
 	struct rsnd_kctrl_cfg_s sync; /* sync convert */
+	u32 current_sync_rate;
 	int irq;
 };
 
@@ -99,7 +100,7 @@ static u32 rsnd_src_convert_rate(struct rsnd_dai_stream *io,
 	if (!rsnd_src_sync_is_enabled(mod))
 		return rsnd_io_converted_rate(io);
 
-	convert_rate = src->sync.val;
+	convert_rate = src->current_sync_rate;
 
 	if (!convert_rate)
 		convert_rate = rsnd_io_converted_rate(io);
@@ -200,13 +201,73 @@ static const u32 chan222222[] = {
 static void rsnd_src_set_convert_rate(struct rsnd_dai_stream *io,
 				      struct rsnd_mod *mod)
 {
+	struct snd_pcm_runtime *runtime = rsnd_io_to_runtime(io);
 	struct rsnd_priv *priv = rsnd_mod_to_priv(mod);
-	struct device *dev = rsnd_priv_to_dev(priv);
+	struct rsnd_src *src = rsnd_mod_to_src(mod);
+	u32 fin, fout, new_rate;
+	int inc, cnt, rate;
+	u64 base, val;
+
+	if (!runtime)
+		return;
+
+	if (!rsnd_src_sync_is_enabled(mod))
+		return;
+
+	fin	= rsnd_src_get_in_rate(priv, io);
+	fout	= rsnd_src_get_out_rate(priv, io);
+
+	new_rate = src->sync.val;
+
+	if (!new_rate)
+		new_rate = fout;
+
+	/* Do nothing if no diff */
+	if (new_rate == src->current_sync_rate)
+		return;
+
+	/*
+	 * SRCm_IFSVR::INTIFS can change within 1%
+	 * see
+	 *	SRCm_IFSVR::INTIFS Note
+	 */
+	inc = fout / 100;
+	cnt = abs(new_rate - fout) / inc;
+	if (fout > new_rate)
+		inc *= -1;
+
+	/*
+	 * After start running SRC, we can update only SRC_IFSVR
+	 * for Synchronous Mode
+	 */
+	base = (u64)0x0400000 * fin;
+	rate  = fout;
+	for (int i = 0; i < cnt; i++) {
+		val   = base;
+		rate += inc;
+		do_div(val, rate);
+
+		rsnd_mod_write(mod, SRC_IFSVR, val);
+	}
+	val   = base;
+	do_div(val, new_rate);
+
+	rsnd_mod_write(mod, SRC_IFSVR, val);
+
+	/* update current_sync_rate */
+	src->current_sync_rate = new_rate;
+}
+
+static void rsnd_src_init_convert_rate(struct rsnd_dai_stream *io,
+				       struct rsnd_mod *mod)
+{
 	struct snd_pcm_runtime *runtime = rsnd_io_to_runtime(io);
+	struct rsnd_priv *priv = rsnd_mod_to_priv(mod);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	int is_play = rsnd_io_is_play(io);
 	int use_src = 0;
 	u32 fin, fout;
-	u32 ifscr, fsrate, adinr;
+	u32 ifscr, adinr;
 	u32 cr, route;
 	u32 i_busif, o_busif, tmp;
 	const u32 *bsdsr_table;
@@ -244,26 +305,15 @@ static void rsnd_src_set_convert_rate(struct rsnd_dai_stream *io,
 	adinr = rsnd_get_adinr_bit(mod, io) | chan;
 
 	/*
-	 * SRC_IFSCR / SRC_IFSVR
-	 */
-	ifscr = 0;
-	fsrate = 0;
-	if (use_src) {
-		u64 n;
-
-		ifscr = 1;
-		n = (u64)0x0400000 * fin;
-		do_div(n, fout);
-		fsrate = n;
-	}
-
-	/*
+	 * SRC_IFSCR
 	 * SRC_SRCCR / SRC_ROUTE_MODE0
 	 */
+	ifscr	= 0;
 	cr	= 0x00011110;
 	route	= 0x0;
 	if (use_src) {
 		route	= 0x1;
+		ifscr	= 0x1;
 
 		if (rsnd_src_sync_is_enabled(mod)) {
 			cr |= 0x1;
@@ -334,7 +384,6 @@ static void rsnd_src_set_convert_rate(struct rsnd_dai_stream *io,
 	rsnd_mod_write(mod, SRC_SRCIR, 1);	/* initialize */
 	rsnd_mod_write(mod, SRC_ADINR, adinr);
 	rsnd_mod_write(mod, SRC_IFSCR, ifscr);
-	rsnd_mod_write(mod, SRC_IFSVR, fsrate);
 	rsnd_mod_write(mod, SRC_SRCCR, cr);
 	rsnd_mod_write(mod, SRC_BSDSR, bsdsr_table[idx]);
 	rsnd_mod_write(mod, SRC_BSISR, bsisr_table[idx]);
@@ -347,6 +396,9 @@ static void rsnd_src_set_convert_rate(struct rsnd_dai_stream *io,
 
 	rsnd_adg_set_src_timesel_gen2(mod, io, fin, fout);
 
+	/* update SRC_IFSVR */
+	rsnd_src_set_convert_rate(io, mod);
+
 	return;
 
 convert_rate_err:
@@ -466,7 +518,8 @@ static int rsnd_src_init(struct rsnd_mod *mod,
 	int ret;
 
 	/* reset sync convert_rate */
-	src->sync.val = 0;
+	src->sync.val		=
+	src->current_sync_rate	= 0;
 
 	ret = rsnd_mod_power_on(mod);
 	if (ret < 0)
@@ -474,7 +527,7 @@ static int rsnd_src_init(struct rsnd_mod *mod,
 
 	rsnd_src_activation(mod);
 
-	rsnd_src_set_convert_rate(io, mod);
+	rsnd_src_init_convert_rate(io, mod);
 
 	rsnd_src_status_clear(mod);
 
@@ -492,7 +545,8 @@ static int rsnd_src_quit(struct rsnd_mod *mod,
 	rsnd_mod_power_off(mod);
 
 	/* reset sync convert_rate */
-	src->sync.val = 0;
+	src->sync.val		=
+	src->current_sync_rate	= 0;
 
 	return 0;
 }
@@ -600,7 +654,7 @@ static int rsnd_src_pcm_new(struct rsnd_mod *mod,
 			       "SRC Out Rate Switch" :
 			       "SRC In Rate Switch",
 			       rsnd_kctrl_accept_anytime,
-			       rsnd_src_set_convert_rate,
+			       rsnd_src_init_convert_rate,
 			       &src->sen, 1);
 	if (ret < 0)
 		return ret;
-- 
2.39.5


  parent reply	other threads:[~2025-02-24 11:20 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-02-24 11:19 [PATCH AUTOSEL 6.1 01/12] ALSA: hda/realtek: Limit mic boost on Positivo ARN50 Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 02/12] ASoC: rsnd: don't indicate warning on rsnd_kctrl_accept_runtime() Sasha Levin
2025-02-24 11:19 ` Sasha Levin [this message]
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 04/12] ASoC: arizona/madera: use fsleep() in up/down DAPM event delays Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 05/12] ASoC: cs35l41: Fallback to using HID for system_name if no SUB is available Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 06/12] ASoC: SOF: Intel: hda: add softdep pre to snd-hda-codec-hdmi module Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 07/12] net: wwan: mhi_wwan_mbim: Silence sequence number glitch errors Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 08/12] nvme-pci: quirk Acer FA100 for non-uniqueue identifiers Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 09/12] nvme-tcp: add basic support for the C2HTermReq PDU Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 10/12] nvmet-rdma: recheck queue state is LIVE in state lock in recv done Sasha Levin
2025-02-24 11:19 ` [PATCH AUTOSEL 6.1 11/12] sctp: Fix undefined behavior in left shift operation Sasha Levin
2025-02-24 11:20 ` [PATCH AUTOSEL 6.1 12/12] nvme: only allow entering LIVE from CONNECTING state Sasha Levin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250224112002.2214613-3-sashal@kernel.org \
    --to=sashal@kernel.org \
    --cc=broonie@kernel.org \
    --cc=kuninori.morimoto.gx@renesas.com \
    --cc=lgirdwood@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sound@vger.kernel.org \
    --cc=perex@perex.cz \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=stable@vger.kernel.org \
    --cc=tiwai@suse.com \
    --cc=yoshihiro.shimoda.uh@renesas.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.