[PATCH 1/1] dt-bindings: gpio: Move fsl,mxs-pinctrl.txt into gpio-mxs.yaml

[Frank Li <Frank.Li@nxp.com>]

Move mxs-pinctrl part into gpio-mxs.yaml and add pinctrl examples to fix
below CHECK_DTB warning:

arch/arm/boot/dts/nxp/mxs/imx28-xea.dtb: pinctrl@80018000 (fsl,imx28-pinctrl):
   'auart0-2pins@0', 'auart0@0',  ... 'usb1@1' do not match any of the regexes: 'gpio@[0-9]+$', 'pinctrl-[0-9]+'

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 .../devicetree/bindings/gpio/gpio-mxs.yaml    |  73 +++++++++-
 .../bindings/pinctrl/fsl,mxs-pinctrl.txt      | 127 ------------------
 2 files changed, 69 insertions(+), 131 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml b/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml
index b58e08c8ecd8a..b3cf4682be3fd 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml
@@ -18,9 +18,11 @@ description: |
 
 properties:
   compatible:
-    enum:
-      - fsl,imx23-pinctrl
-      - fsl,imx28-pinctrl
+    items:
+      - enum:
+          - fsl,imx23-pinctrl
+          - fsl,imx28-pinctrl
+      - const: simple-bus
 
   '#address-cells':
     const: 1
@@ -31,6 +33,61 @@ properties:
     maxItems: 1
 
 patternProperties:
+  "^(?!gpio).*@[0-9]+$":
+    type: object
+    properties:
+      fsl,pinmux-ids:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        description: |
+          An integer array.  Each integer in the array specify a pin
+          with given mux function, with bank, pin and mux packed as below.
+
+          [15..12] : bank number
+          [11..4]  : pin number
+          [3..0]   : mux selection
+
+          This integer with mux selection packed is used as an entity by both group
+          and config nodes to identify a pin.  The mux selection in the integer takes
+          effects only on group node, and will get ignored by driver with config node,
+          since config node is only meant to set up pin configurations.
+
+          Valid values for these integers are listed below.
+
+      reg:
+        maxItems: 1
+
+      fsl,drive-strength:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        description: |
+          0: MXS_DRIVE_4mA
+          1: MXS_DRIVE_8mA
+          2: MXS_DRIVE_12mA
+          3: MXS_DRIVE_16mA
+
+      fsl,voltage:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1]
+        description: |
+          0: MXS_VOLTAGE_LOW  - 1.8 V
+          1: MXS_VOLTAGE_HIGH - 3.3 V
+
+      fsl,pull-up:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1]
+        description: |
+          0: MXS_PULL_DISABLE - Disable the internal pull-up
+          1: MXS_PULL_ENABLE  - Enable the internal pull-up
+
+          Note that when enabling the pull-up, the internal pad keeper gets disabled.
+          Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
+          will only disable the internal pad keeper.
+
+    required:
+      - fsl,pinmux-ids
+
+    additionalProperties: false
+
   "gpio@[0-9]+$":
     type: object
     properties:
@@ -80,7 +137,7 @@ examples:
     pinctrl@80018000 {
         #address-cells = <1>;
         #size-cells = <0>;
-        compatible = "fsl,imx28-pinctrl";
+        compatible = "fsl,imx28-pinctrl", "simple-bus";
         reg = <0x80018000 0x2000>;
 
         gpio@0 {
@@ -132,4 +189,12 @@ examples:
             interrupt-controller;
             #interrupt-cells = <2>;
         };
+
+        lcdif-apx4@5 {
+            reg = <5>;
+            fsl,pinmux-ids = <0x1181 0x1191>;
+            fsl,drive-strength = <0>;
+            fsl,voltage = <0>;
+            fsl,pull-up = <0>;
+        };
     };
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
deleted file mode 100644
index 1e70a8aff2600..0000000000000
--- a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
+++ /dev/null
@@ -1,127 +0,0 @@
-* Freescale MXS Pin Controller
-
-The pins controlled by mxs pin controller are organized in banks, each bank
-has 32 pins.  Each pin has 4 multiplexing functions, and generally, the 4th
-function is GPIO.  The configuration on the pins includes drive strength,
-voltage and pull-up.
-
-Required properties:
-- compatible: "fsl,imx23-pinctrl" or "fsl,imx28-pinctrl"
-- reg: Should contain the register physical address and length for the
-  pin controller.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices.
-
-The node of mxs pin controller acts as a container for an arbitrary number of
-subnodes.  Each of these subnodes represents some desired configuration for
-a group of pins, and only affects those parameters that are explicitly listed.
-In other words, a subnode that describes a drive strength parameter implies no
-information about pull-up. For this reason, even seemingly boolean values are
-actually tristates in this binding: unspecified, off, or on. Unspecified is
-represented as an absent property, and off/on are represented as integer
-values 0 and 1.
-
-Those subnodes under mxs pin controller node will fall into two categories.
-One is to set up a group of pins for a function, both mux selection and pin
-configurations, and it's called group node in the binding document.   The other
-one is to adjust the pin configuration for some particular pins that need a
-different configuration than what is defined in group node.  The binding
-document calls this type of node config node.
-
-On mxs, there is no hardware pin group. The pin group in this binding only
-means a group of pins put together for particular peripheral to work in
-particular function, like SSP0 functioning as mmc0-8bit.  That said, the
-group node should include all the pins needed for one function rather than
-having these pins defined in several group nodes.  It also means each of
-"pinctrl-*" phandle in client device node should only have one group node
-pointed in there, while the phandle can have multiple config node referenced
-there to adjust configurations for some pins in the group.
-
-Required subnode-properties:
-- fsl,pinmux-ids: An integer array.  Each integer in the array specify a pin
-  with given mux function, with bank, pin and mux packed as below.
-
-    [15..12] : bank number
-    [11..4]  : pin number
-    [3..0]   : mux selection
-
-  This integer with mux selection packed is used as an entity by both group
-  and config nodes to identify a pin.  The mux selection in the integer takes
-  effects only on group node, and will get ignored by driver with config node,
-  since config node is only meant to set up pin configurations.
-
-  Valid values for these integers are listed below.
-
-- reg: Should be the index of the group nodes for same function.  This property
-  is required only for group nodes, and should not be present in any config
-  nodes.
-
-Optional subnode-properties:
-- fsl,drive-strength: Integer.
-    0: MXS_DRIVE_4mA
-    1: MXS_DRIVE_8mA
-    2: MXS_DRIVE_12mA
-    3: MXS_DRIVE_16mA
-- fsl,voltage: Integer.
-    0: MXS_VOLTAGE_LOW  - 1.8 V
-    1: MXS_VOLTAGE_HIGH - 3.3 V
-- fsl,pull-up: Integer.
-    0: MXS_PULL_DISABLE - Disable the internal pull-up
-    1: MXS_PULL_ENABLE  - Enable the internal pull-up
-
-Note that when enabling the pull-up, the internal pad keeper gets disabled.
-Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
-will only disable the internal pad keeper.
-
-Examples:
-
-pinctrl@80018000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "fsl,imx28-pinctrl";
-	reg = <0x80018000 2000>;
-
-	mmc0_8bit_pins_a: mmc0-8bit@0 {
-		reg = <0>;
-		fsl,pinmux-ids = <
-			MX28_PAD_SSP0_DATA0__SSP0_D0
-			MX28_PAD_SSP0_DATA1__SSP0_D1
-			MX28_PAD_SSP0_DATA2__SSP0_D2
-			MX28_PAD_SSP0_DATA3__SSP0_D3
-			MX28_PAD_SSP0_DATA4__SSP0_D4
-			MX28_PAD_SSP0_DATA5__SSP0_D5
-			MX28_PAD_SSP0_DATA6__SSP0_D6
-			MX28_PAD_SSP0_DATA7__SSP0_D7
-			MX28_PAD_SSP0_CMD__SSP0_CMD
-			MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
-			MX28_PAD_SSP0_SCK__SSP0_SCK
-		>;
-		fsl,drive-strength = <MXS_DRIVE_4mA>;
-		fsl,voltage = <MXS_VOLTAGE_HIGH>;
-		fsl,pull-up = <MXS_PULL_ENABLE>;
-	};
-
-	mmc_cd_cfg: mmc-cd-cfg {
-		fsl,pinmux-ids = <MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT>;
-		fsl,pull-up = <MXS_PULL_DISABLE>;
-	};
-
-	mmc_sck_cfg: mmc-sck-cfg {
-		fsl,pinmux-ids = <MX28_PAD_SSP0_SCK__SSP0_SCK>;
-		fsl,drive-strength = <MXS_DRIVE_12mA>;
-		fsl,pull-up = <MXS_PULL_DISABLE>;
-	};
-};
-
-In this example, group node mmc0-8bit defines a group of pins for mxs SSP0
-to function as a 8-bit mmc device, with 8mA, 3.3V and pull-up configurations
-applied on all these pins.  And config nodes mmc-cd-cfg and mmc-sck-cfg are
-adjusting the configuration for pins card-detection and clock from what group
-node mmc0-8bit defines.  Only the configuration properties to be adjusted need
-to be listed in the config nodes.
-
-Valid values for i.MX28/i.MX23 pinmux-id are defined in
-arch/arm/boot/dts/imx28-pinfunc.h and arch/arm/boot/dts/imx23-pinfunc.h.
-The definitions for the padconfig properties can be found in
-arch/arm/boot/dts/mxs-pinfunc.h.
-- 
2.34.1