From: Richard Leitner <richard.leitner@linux.dev>
To: Sakari Ailus <sakari.ailus@linux.intel.com>,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Lee Jones <lee@kernel.org>, Pavel Machek <pavel@kernel.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>,
linux-media@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-leds@vger.kernel.org,
Richard Leitner <richard.leitner@linux.dev>
Subject: [PATCH v6 06/11] media: i2c: ov9282: add output enable register definitions
Date: Wed, 16 Jul 2025 11:06:56 +0200 [thread overview]
Message-ID: <20250716-ov9282-flash-strobe-v6-6-934f12aeff33@linux.dev> (raw)
In-Reply-To: <20250716-ov9282-flash-strobe-v6-0-934f12aeff33@linux.dev>
Add #define's for the output enable registers (0x3004, 0x3005, 0x3006),
also known as SC_CTRL_04, SC_CTRL_05, SC_CTRL_04. Use those register
definitions instead of the raw values in the `common_regs` struct.
All values are based on the OV9281 datasheet v1.53 (january 2019).
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
---
drivers/media/i2c/ov9282.c | 29 ++++++++++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)
diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
index c882a021cf18852237bf9b9524d3de0c5b48cbcb..f42e0d439753e74d14e3a3592029e48f49234927 100644
--- a/drivers/media/i2c/ov9282.c
+++ b/drivers/media/i2c/ov9282.c
@@ -37,6 +37,29 @@
#define OV9282_REG_ID 0x300a
#define OV9282_ID 0x9281
+/* Output enable registers */
+#define OV9282_REG_OUTPUT_ENABLE4 0x3004
+#define OV9282_OUTPUT_ENABLE4_GPIO2 BIT(1)
+#define OV9282_OUTPUT_ENABLE4_D9 BIT(0)
+
+#define OV9282_REG_OUTPUT_ENABLE5 0x3005
+#define OV9282_OUTPUT_ENABLE5_D8 BIT(7)
+#define OV9282_OUTPUT_ENABLE5_D7 BIT(6)
+#define OV9282_OUTPUT_ENABLE5_D6 BIT(5)
+#define OV9282_OUTPUT_ENABLE5_D5 BIT(4)
+#define OV9282_OUTPUT_ENABLE5_D4 BIT(3)
+#define OV9282_OUTPUT_ENABLE5_D3 BIT(2)
+#define OV9282_OUTPUT_ENABLE5_D2 BIT(1)
+#define OV9282_OUTPUT_ENABLE5_D1 BIT(0)
+
+#define OV9282_REG_OUTPUT_ENABLE6 0x3006
+#define OV9282_OUTPUT_ENABLE6_D0 BIT(7)
+#define OV9282_OUTPUT_ENABLE6_PCLK BIT(6)
+#define OV9282_OUTPUT_ENABLE6_HREF BIT(5)
+#define OV9282_OUTPUT_ENABLE6_STROBE BIT(3)
+#define OV9282_OUTPUT_ENABLE6_ILPWM BIT(2)
+#define OV9282_OUTPUT_ENABLE6_VSYNC BIT(1)
+
/* Exposure control */
#define OV9282_REG_EXPOSURE 0x3500
#define OV9282_EXPOSURE_MIN 1
@@ -213,9 +236,9 @@ static const struct ov9282_reg common_regs[] = {
{0x0302, 0x32},
{0x030e, 0x02},
{0x3001, 0x00},
- {0x3004, 0x00},
- {0x3005, 0x00},
- {0x3006, 0x04},
+ {OV9282_REG_OUTPUT_ENABLE4, 0x00},
+ {OV9282_REG_OUTPUT_ENABLE5, 0x00},
+ {OV9282_REG_OUTPUT_ENABLE6, OV9282_OUTPUT_ENABLE6_ILPWM},
{0x3011, 0x0a},
{0x3013, 0x18},
{0x301c, 0xf0},
--
2.47.2
next prev parent reply other threads:[~2025-07-16 9:06 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-16 9:06 [PATCH v6 00/11] Add strobe duration and hw strobe signal v4l2 ctrl & use it for ov9282 Richard Leitner
2025-07-16 9:06 ` [PATCH v6 01/11] media: v4l: ctrls: add a control for flash/strobe duration Richard Leitner
2025-07-16 9:06 ` [PATCH v6 02/11] media: v4l2-flash: add support " Richard Leitner
2025-07-16 9:06 ` [PATCH v6 03/11] Documentation: uAPI: media: add V4L2_CID_FLASH_DURATION Richard Leitner
2025-08-25 5:42 ` Sakari Ailus
2025-08-25 5:48 ` Sakari Ailus
2025-08-25 18:45 ` Richard Leitner
2025-09-01 10:44 ` Richard Leitner
2025-09-01 12:11 ` Sakari Ailus
2025-07-16 9:06 ` [PATCH v6 04/11] media: v4l: ctrls: add a control for enabling hw strobe signal Richard Leitner
2025-07-16 9:06 ` [PATCH v6 05/11] Documentation: uAPI: media: add V4L2_CID_FLASH_HW_STROBE_SIGNAL Richard Leitner
2025-07-16 9:06 ` Richard Leitner [this message]
2025-07-16 9:06 ` [PATCH v6 07/11] media: i2c: ov9282: add hardware strobe signal v4l2 control Richard Leitner
2025-07-16 9:06 ` [PATCH v6 08/11] media: i2c: ov9282: add strobe_duration " Richard Leitner
2025-07-16 9:06 ` [PATCH v6 09/11] media: i2c: ov9282: add strobe_source " Richard Leitner
2025-07-16 9:07 ` [PATCH v6 10/11] media: i2c: ov9282: implement try_ctrl for strobe_duration Richard Leitner
2025-07-17 8:53 ` kernel test robot
2025-07-16 9:07 ` [PATCH v6 11/11] media: i2c: ov9282: dynamic flash_duration maximum Richard Leitner
2025-08-24 19:03 ` [PATCH v6 00/11] Add strobe duration and hw strobe signal v4l2 ctrl & use it for ov9282 Richard Leitner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250716-ov9282-flash-strobe-v6-6-934f12aeff33@linux.dev \
--to=richard.leitner@linux.dev \
--cc=dave.stevenson@raspberrypi.com \
--cc=hverkuil@xs4all.nl \
--cc=laurent.pinchart@ideasonboard.com \
--cc=lee@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=pavel@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.