[PATCH v6 8/8] ARM: dts: r9a06g032: Add support for GPIO interrupts

["Herve Codina (Schneider Electric)" <herve.codina@bootlin.com>]

In the RZ/N1 SoC, the GPIO interrupts are multiplexed using the GPIO
Interrupt Multiplexer.

Add the multiplexer node and connect GPIO interrupt lines to the
multiplexer.

The interrupt-map available in the multiplexer node has to be updated in
dts files depending on the GPIO usage. Indeed, the usage of an interrupt
for a GPIO is board dependent.

Up to 8 GPIOs can be used as an interrupt line (one per multiplexer
output interrupt).

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 41 ++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index da977cdd8487..c7196e720c6c 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -534,6 +534,14 @@ gpio0a: gpio-port@0 {
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
 				reg = <0>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = < 0  1  2  3  4  5  6  7
+					       8  9 10 11 12 13 14 15
+					      16 17 18 19 20 21 22 23
+					      24 25 26 27 28 29 30 31 >;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO0b[0..1]   connected to pins GPIO1..2   */
@@ -576,6 +584,14 @@ gpio1a: gpio-port@0 {
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
 				reg = <0>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = < 32 33 34 35 36 37 38 39
+					       40 41 42 43 44 45 46 47
+					       48 49 50 51 52 53 54 55
+					       56 57 58 59 60 61 62 63 >;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO1b[0..1]   connected to pins GPIO55..56 */
@@ -608,6 +624,14 @@ gpio2a: gpio-port@0 {
 				#gpio-cells = <2>;
 				snps,nr-gpios = <32>;
 				reg = <0>;
+
+				interrupt-controller;
+				interrupt-parent = <&gpioirqmux>;
+				interrupts = < 64 65 66 67 68 69 70 71
+					       72 73 74 75 76 77 78 79
+					       80 81 82 83 84 85 86 87
+					       88 89 90 91 92 93 94 95 >;
+				#interrupt-cells = <2>;
 			};
 
 			/* GPIO2b[0..9] connected to pins GPIO160..169 */
@@ -620,6 +644,23 @@ gpio2b: gpio-port@1 {
 			};
 		};
 
+		gpioirqmux: interrupt-controller@51000480 {
+			compatible = "renesas,r9a06g032-gpioirqmux", "renesas,rzn1-gpioirqmux";
+			reg = <0x51000480 0x20>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			interrupt-map-mask = <0x7f>;
+
+			/*
+			 * Example mapping entry. Board DTs need to overwrite
+			 * 'interrupt-map' with their specific mapping. Check
+			 * the irqmux binding documentation for details.
+			 */
+			interrupt-map = <0 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
+		};
+
 		can0: can@52104000 {
 			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
 			reg = <0x52104000 0x800>;
-- 
2.51.0