From: Sudarshan Shetty <tessolveupstream@gmail.com>
To: andersson@kernel.org, konradybcio@kernel.org
Cc: robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Sudarshan Shetty <tessolveupstream@gmail.com>
Subject: [PATCH v8 2/2] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Date: Sat, 29 Nov 2025 19:52:42 +0530 [thread overview]
Message-ID: <20251129142242.3661349-3-tessolveupstream@gmail.com> (raw)
In-Reply-To: <20251129142242.3661349-1-tessolveupstream@gmail.com>
Add the device tree for the QCS615-based Talos EVK platform. The
platform is composed of a System-on-Module following the SMARC
standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and
LVDS. Both configurations use the same base hardware, with the display
selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an
overlay that disables HDMI and adds LVDS. The DTs file talos-evk
can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 3 +
.../qcom/talos-evk-lvds-auo,g133han01.dtso | 131 +++++
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 447 ++++++++++++++++++
arch/arm64/boot/dts/qcom/talos-evk.dts | 137 ++++++
4 files changed, 718 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5b52f9e4e5f3..94c20074397c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -305,6 +305,9 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb
+talos-evk-lvds-auo,g133han01-dtbs := talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb
x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..2a90d61892e7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ backlight: backlight {
+ compatible = "gpio-backlight";
+ gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>;
+ default-on;
+ };
+
+ hdmi-out {
+ status = "disabled";
+ };
+
+ lcd-pwm-en {
+ compatible = "gpio-backlight";
+ gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>;
+ default-on;
+ };
+
+ panel-lvds {
+ compatible = "auo,g133han01";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* LVDS A (Odd pixels) */
+ port@0 {
+ reg = <0>;
+ dual-lvds-odd-pixels;
+
+ lvds_panel_out_a: endpoint {
+ remote-endpoint = <&sn65dsi84_out_a>;
+ };
+ };
+
+ /* LVDS B (Even pixels) */
+ port@1 {
+ reg = <1>;
+ dual-lvds-even-pixels;
+
+ lvds_panel_out_b: endpoint {
+ remote-endpoint = <&sn65dsi84_out_b>;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ bridge@3d {
+ status = "disabled";
+ };
+
+ bridge: bridge@2c {
+ compatible = "ti,sn65dsi84";
+ reg = <0x2c>;
+ enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+ ti,dsi-lanes = <4>;
+ ti,lvds-format = "jeida-24";
+ ti,lvds-bpp = <24>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ sn65dsi84_in: endpoint {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ sn65dsi84_out_a: endpoint {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&lvds_panel_out_a>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+
+ sn65dsi84_out_b: endpoint {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&lvds_panel_out_b>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&sn65dsi84_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&tlmm {
+ lcd_bklt_en: lcd-bklt-en-state {
+ pins = "gpio115";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lcd_bklt_pwm: lcd-bklt-pwm-state {
+ pins = "gpio59";
+ function = "gpio";
+ bias-disable;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
new file mode 100644
index 000000000000..7b576c7bf903
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
@@ -0,0 +1,447 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "talos.dtsi"
+#include "pm8150.dtsi"
+/ {
+ aliases {
+ mmc0 = &sdhc_1;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ #clock-cells = <0>;
+ };
+
+ xo_board_clk: xo-board-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ regulator-usb2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "USB2_VBUS";
+ gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb2_en>;
+ pinctrl-names = "default";
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ vreg_v3p3_can: regulator-v3p3-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-can";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v5p0_can: regulator-v5p0-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-can";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s3a: smps3 {
+ regulator-name = "vreg_s3a";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <650000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1829000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a: smps5 {
+ regulator-name = "vreg_s5a";
+ regulator-min-microvolt = <1896000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6a: smps6 {
+ regulator-name = "vreg_s6a";
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1404000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1a: ldo1 {
+ regulator-name = "vreg_l1a";
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <852000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a: ldo2 {
+ regulator-name = "vreg_l2a";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1248000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <975000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10a: ldo10 {
+ regulator-name = "vreg_l10a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11a: ldo11 {
+ regulator-name = "vreg_l11a";
+ regulator-min-microvolt = <1232000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a: ldo12 {
+ regulator-name = "vreg_l12a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3230000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15a: ldo15 {
+ regulator-name = "vreg_l15a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16a: ldo16 {
+ regulator-name = "vreg_l16a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a: ldo17 {
+ regulator-name = "vreg_l17a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+
+ eeprom@5f {
+ compatible = "atmel,24mac602";
+ reg = <0x5f>;
+ pagesize = <16>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
+ remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss_dp_phy {
+ vdda-phy-supply = <&vreg_l11a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&pcie {
+ perst-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&pcie_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&pm8150_gpios {
+ usb2_en: usb2-en-state {
+ pins = "gpio10";
+ function = "normal";
+ output-enable;
+ power-source = <0>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs615/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs615/cdsp.mbn";
+
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ vmmc-supply = <&vreg_l17a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ status = "okay";
+};
+
+&spi6 {
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ clock-frequency = <20000000>;
+ interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <10000000>;
+ vdd-supply = <&vreg_v3p3_can>;
+ xceiver-supply = <&vreg_v5p0_can>;
+ };
+};
+
+&tlmm {
+ pcie_default_state: pcie-default-state {
+ clkreq-pins {
+ pins = "gpio90";
+ function = "pcie_clk_req";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio101";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wake-pins {
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_hsphy_2 {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17a>;
+ vcc-max-microamp = <600000>;
+ vccq2-supply = <&vreg_s4a>;
+ vccq2-max-microamp = <600000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&venus {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk.dts b/arch/arm64/boot/dts/qcom/talos-evk.dts
new file mode 100644
index 000000000000..c2f9a940c7a9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "talos-evk-som.dtsi"
+
+/ {
+ model = "Qualcomm QCS615 IQ 615 EVK";
+ compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150";
+ chassis-type = "embedded";
+
+ aliases {
+ mmc1 = &sdhc_2;
+ };
+
+ dp-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+
+ hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&mdss_dp0_out>;
+ };
+ };
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "d";
+
+ port {
+ hdmi_con_out: endpoint {
+ remote-endpoint = <&adv7535_out>;
+ };
+ };
+ };
+
+ vreg_v1p8_out: regulator-v1p8-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v1p8-out";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v3p3_out: regulator-v3p3-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-out";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v5p0_out: regulator-v5p0-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-out";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ /* Powered by system 20V rail (USBC_VBUS_IN) */
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ status = "okay";
+ bridge: bridge@3d {
+ compatible = "adi,adv7535";
+ reg = <0x3d>;
+ avdd-supply = <&vreg_v1p8_out>;
+ dvdd-supply = <&vreg_v1p8_out>;
+ pvdd-supply = <&vreg_v1p8_out>;
+ a2vdd-supply = <&vreg_v1p8_out>;
+ v3p3-supply = <&vreg_v3p3_out>;
+ interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>;
+ adi,dsi-lanes = <4>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ adv7535_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ adv7535_out: endpoint {
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&adv7535_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_state_on>;
+ pinctrl-1 = <&sdc2_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vreg_l10a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ status = "okay";
+};
--
2.34.1
prev parent reply other threads:[~2025-11-29 14:23 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-11-29 14:22 [PATCH v8 0/2] Add Qualcomm Technologies, Inc. Talos EVK SMARC support Sudarshan Shetty
2025-11-29 14:22 ` [PATCH v8 1/2] dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform Sudarshan Shetty
2025-11-29 15:22 ` Rob Herring (Arm)
2025-12-01 17:20 ` tessolveupstream
2025-11-29 14:22 ` Sudarshan Shetty [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251129142242.3661349-3-tessolveupstream@gmail.com \
--to=tessolveupstream@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.