All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ping-Ke Shih <pkshih@realtek.com>
To: <linux-wireless@vger.kernel.org>
Cc: <gary.chang@realtek.com>, <damon.chen@realtek.com>,
	<kevin_yang@realtek.com>
Subject: [PATCH rtw-next 10/12] wifi: rtw89: warn unexpected polling value of XTAL SI
Date: Fri, 12 Dec 2025 11:13:01 +0800	[thread overview]
Message-ID: <20251212031303.19882-11-pkshih@realtek.com> (raw)
In-Reply-To: <20251212031303.19882-1-pkshih@realtek.com>

XTAL SI is an indirect serial interface to access registers in another
hardware domain. When BT driver initializes UART interface, firmware might
rarely control XTAL SI at the same time causing access racing.

Current is to adjust initialization flow to avoid the racing. To make
the racing visible if it still presents, add a message to address this.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
---
 drivers/net/wireless/realtek/rtw89/mac.c    | 11 ++++++++++-
 drivers/net/wireless/realtek/rtw89/mac_be.c | 11 ++++++++++-
 2 files changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtw89/mac.c b/drivers/net/wireless/realtek/rtw89/mac.c
index cf36be167162..066c99f3e53a 100644
--- a/drivers/net/wireless/realtek/rtw89/mac.c
+++ b/drivers/net/wireless/realtek/rtw89/mac.c
@@ -7023,6 +7023,11 @@ int rtw89_mac_write_xtal_si_ax(struct rtw89_dev *rtwdev, u8 offset, u8 val, u8 m
 		return ret;
 	}
 
+	if (u32_get_bits(val32, B_AX_WL_XTAL_SI_ADDR_MASK) != offset ||
+	    u32_get_bits(val32, B_AX_WL_XTAL_SI_DATA_MASK) != val)
+		rtw89_warn(rtwdev, "xtal si write: offset=%x val=%x poll=%x\n",
+			   offset, val, val32);
+
 	return 0;
 }
 
@@ -7046,7 +7051,11 @@ int rtw89_mac_read_xtal_si_ax(struct rtw89_dev *rtwdev, u8 offset, u8 *val)
 		return ret;
 	}
 
-	*val = rtw89_read8(rtwdev, R_AX_WLAN_XTAL_SI_CTRL + 1);
+	if (u32_get_bits(val32, B_AX_WL_XTAL_SI_ADDR_MASK) != offset)
+		rtw89_warn(rtwdev, "xtal si read: offset=%x poll=%x\n",
+			   offset, val32);
+
+	*val = u32_get_bits(val32, B_AX_WL_XTAL_SI_DATA_MASK);
 
 	return 0;
 }
diff --git a/drivers/net/wireless/realtek/rtw89/mac_be.c b/drivers/net/wireless/realtek/rtw89/mac_be.c
index 2bc329c13443..d75c55cc34b8 100644
--- a/drivers/net/wireless/realtek/rtw89/mac_be.c
+++ b/drivers/net/wireless/realtek/rtw89/mac_be.c
@@ -396,6 +396,11 @@ int rtw89_mac_write_xtal_si_be(struct rtw89_dev *rtwdev, u8 offset, u8 val, u8 m
 		return ret;
 	}
 
+	if (u32_get_bits(val32, B_BE_WL_XTAL_SI_ADDR_MASK) != offset ||
+	    u32_get_bits(val32, B_BE_WL_XTAL_SI_DATA_MASK) != val)
+		rtw89_warn(rtwdev, "xtal si write: offset=%x val=%x poll=%x\n",
+			   offset, val, val32);
+
 	return 0;
 }
 
@@ -420,7 +425,11 @@ int rtw89_mac_read_xtal_si_be(struct rtw89_dev *rtwdev, u8 offset, u8 *val)
 		return ret;
 	}
 
-	*val = rtw89_read8(rtwdev, R_BE_WLAN_XTAL_SI_CTRL + 1);
+	if (u32_get_bits(val32, B_BE_WL_XTAL_SI_ADDR_MASK) != offset)
+		rtw89_warn(rtwdev, "xtal si read: offset=%x poll=%x\n",
+			   offset, val32);
+
+	*val = u32_get_bits(val32, B_BE_WL_XTAL_SI_DATA_MASK);
 
 	return 0;
 }
-- 
2.25.1


  parent reply	other threads:[~2025-12-12  3:14 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-12-12  3:12 [PATCH rtw-next 00/12] wifi: rtw89: refine MLO, MCC and SER functions Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 01/12] wifi: rtw89: 8852b: increase beacon loss to 6 seconds Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 02/12] wifi: rtw89: mlo: fix missing TX null-data 1 during link switch Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 03/12] wifi: rtw89: mlo: fix incorrect link address in management frames Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 04/12] wifi: rtw89: mac: reset power state before switching to power on Ping-Ke Shih
2025-12-14 22:30   ` Bitterblue Smith
2025-12-15  2:05     ` Ping-Ke Shih
2025-12-15 18:06       ` Bitterblue Smith
2025-12-16  0:34         ` Ping-Ke Shih
2025-12-16  9:06           ` Ping-Ke Shih
2025-12-17 18:05             ` Bitterblue Smith
2025-12-12  3:12 ` [PATCH rtw-next 05/12] wifi: rtw89: ser: enable error IMR after recovering from L1 Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 06/12] wifi: rtw89: ser: L1 skip polling status if FW runs event mode Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 07/12] wifi: rtw89: debug: add ser_counters dbgfs Ping-Ke Shih
2025-12-12  3:12 ` [PATCH rtw-next 08/12] wifi: rtw89: debug: support SER L0/L1 simulation via halt H2C Ping-Ke Shih
2025-12-12  3:13 ` [PATCH rtw-next 09/12] wifi: rtw89: refine C2H reg event polling timeout for LPS Ping-Ke Shih
2025-12-12  3:13 ` Ping-Ke Shih [this message]
2025-12-14 22:32   ` [PATCH rtw-next 10/12] wifi: rtw89: warn unexpected polling value of XTAL SI Bitterblue Smith
2025-12-15  1:24     ` Ping-Ke Shih
2025-12-15 22:13       ` Bitterblue Smith
2025-12-16  0:29         ` Ping-Ke Shih
2025-12-12  3:13 ` [PATCH rtw-next 11/12] wifi: rtw89: setting TBTT AGG number when mac port initialization Ping-Ke Shih
2025-12-12  3:13 ` [PATCH rtw-next 12/12] wifi: rtw89: mcc: reset probe counter when receiving beacon Ping-Ke Shih

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20251212031303.19882-11-pkshih@realtek.com \
    --to=pkshih@realtek.com \
    --cc=damon.chen@realtek.com \
    --cc=gary.chang@realtek.com \
    --cc=kevin_yang@realtek.com \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.