From: Sudarshan Shetty <tessolveupstream@gmail.com>
To: andersson@kernel.org, konradybcio@kernel.org
Cc: robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Sudarshan Shetty <tessolveupstream@gmail.com>,
Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Subject: [PATCH v13 3/3] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Date: Wed, 11 Feb 2026 09:55:34 +0530 [thread overview]
Message-ID: <20260211042534.162007-4-tessolveupstream@gmail.com> (raw)
In-Reply-To: <20260211042534.162007-1-tessolveupstream@gmail.com>
Add the device tree for the QCS615-based Talos EVK platform. The
platform is composed of a System-on-Module following the SMARC
standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and
LVDS. Both configurations use the same base hardware, with the display
selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an
overlay that disables HDMI and adds LVDS. The DTs file talos-evk
can describe the HDMI display configurations.
According to the hardware design and vendor guidance, the WiFi PA
supplies VDD_PA_A and VDD_PA_B only need to be enabled at the same time
as asserting WLAN_EN.
On this platform, WiFi enablement is controlled via the WLAN_EN GPIO
(GPIO84), which also drives the VDD_PA_A and VDD_PA_B power enables.
Remove the VDD_PA_A and VDD_PA_B regulator nodes from the device tree
and rely on WLAN_EN to enable WiFi functionality.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BT
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 6 +
arch/arm64/boot/dts/qcom/qcs615-ride.dts | 4 +-
.../qcom/talos-evk-lvds-auo,g133han01.dtso | 131 ++++
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 609 ++++++++++++++++++
.../dts/qcom/talos-evk-usb1-peripheral.dtso | 10 +
arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++
arch/arm64/boot/dts/qcom/talos.dtsi | 8 +-
7 files changed, 901 insertions(+), 6 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-usb1-peripheral.dtso
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 76cf0115a00a..9b18ec342eae 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -324,6 +324,12 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb
+talos-evk-usb1-peripheral-dtbs := talos-evk.dtb talos-evk-usb1-peripheral.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk-usb1-peripheral.dtb
+talos-evk-lvds-auo,g133han01-dtbs := \
+ talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb
x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 0ca6b50a6de1..a5f763cf1a55 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -609,7 +609,7 @@ bluetooth {
};
};
-&usb_hsphy_1 {
+&usb_1_hsphy {
vdd-supply = <&vreg_l5a>;
vdda-pll-supply = <&vreg_l12a>;
vdda-phy-dpdm-supply = <&vreg_l13a>;
@@ -632,7 +632,7 @@ &usb_1_dwc3 {
dr_mode = "peripheral";
};
-&usb_hsphy_2 {
+&usb_2_hsphy {
vdd-supply = <&vreg_l5a>;
vdda-pll-supply = <&vreg_l12a>;
vdda-phy-dpdm-supply = <&vreg_l13a>;
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..884df2d4f4e1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ backlight: backlight {
+ compatible = "gpio-backlight";
+ gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>,
+ <&tlmm 115 GPIO_ACTIVE_HIGH>;
+ default-on;
+ };
+
+ panel-lvds {
+ compatible = "auo,g133han01";
+ power-supply = <&vreg_v3p3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* LVDS A (Odd pixels) */
+ port@0 {
+ reg = <0>;
+ dual-lvds-odd-pixels;
+
+ lvds_panel_out_a: endpoint {
+ remote-endpoint = <&sn65dsi84_out_a>;
+ };
+ };
+
+ /* LVDS B (Even pixels) */
+ port@1 {
+ reg = <1>;
+ dual-lvds-even-pixels;
+
+ lvds_panel_out_b: endpoint {
+ remote-endpoint = <&sn65dsi84_out_b>;
+ };
+ };
+ };
+ };
+
+ vreg_v3p3: regulator-v3p3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&hdmi_connector {
+ status = "disabled";
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ hdmi_bridge: bridge@3d {
+ status = "disabled";
+ };
+
+ lvds_bridge: bridge@2c {
+ compatible = "ti,sn65dsi84";
+ reg = <0x2c>;
+ enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ sn65dsi84_in: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ sn65dsi84_out_a: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&lvds_panel_out_a>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+
+ sn65dsi84_out_b: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&lvds_panel_out_b>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&sn65dsi84_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&tlmm {
+ lcd_bklt_en: lcd-bklt-en-state {
+ pins = "gpio115";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lcd_bklt_pwm: lcd-bklt-pwm-state {
+ pins = "gpio59";
+ function = "gpio";
+ bias-disable;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
new file mode 100644
index 000000000000..365d77d398d7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
@@ -0,0 +1,609 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "talos.dtsi"
+#include "pm8150.dtsi"
+/ {
+ aliases {
+ mmc0 = &sdhc_1;
+ serial0 = &uart0;
+ serial1 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ can_osc: can-oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <20000000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ #clock-cells = <0>;
+ };
+
+ xo_board_clk: xo-board-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ regulator-usb2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "USB2_VBUS";
+ gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb2_en>;
+ pinctrl-names = "default";
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ vreg_conn_1p8: regulator-conn-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_1p8";
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_conn_pa: regulator-conn-pa {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_pa";
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_v3p3_can: regulator-v3p3-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-can";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v5p0_can: regulator-v5p0-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-can";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ wcn6855-pmu {
+ compatible = "qcom,wcn6855-pmu";
+
+ pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+ pinctrl-names = "default";
+
+ bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+ wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+
+ vddio-supply = <&vreg_conn_pa>;
+ vddaon-supply = <&vreg_s5a>;
+ vddpmu-supply = <&vreg_conn_1p8>;
+ vddpmumx-supply = <&vreg_conn_1p8>;
+ vddpmucx-supply = <&vreg_conn_pa>;
+ vddrfa0p95-supply = <&vreg_s5a>;
+ vddrfa1p3-supply = <&vreg_s6a>;
+ vddrfa1p9-supply = <&vreg_l15a>;
+ vddpcie1p3-supply = <&vreg_s6a>;
+ vddpcie1p9-supply = <&vreg_l15a>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s3a: smps3 {
+ regulator-name = "vreg_s3a";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <650000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1829000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a: smps5 {
+ regulator-name = "vreg_s5a";
+ regulator-min-microvolt = <1896000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6a: smps6 {
+ regulator-name = "vreg_s6a";
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1404000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1a: ldo1 {
+ regulator-name = "vreg_l1a";
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <852000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a: ldo2 {
+ regulator-name = "vreg_l2a";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1248000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <975000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10a: ldo10 {
+ regulator-name = "vreg_l10a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11a: ldo11 {
+ regulator-name = "vreg_l11a";
+ regulator-min-microvolt = <1232000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a: ldo12 {
+ regulator-name = "vreg_l12a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3230000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15a: ldo15 {
+ regulator-name = "vreg_l15a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16a: ldo16 {
+ regulator-name = "vreg_l16a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a: ldo17 {
+ regulator-name = "vreg_l17a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+
+ eeprom@5f {
+ compatible = "atmel,24mac602";
+ reg = <0x5f>;
+ pagesize = <16>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
+ remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+ status = "okay";
+};
+
+&mdss_dsi0_phy {
+ vcca-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
+&pcie {
+ perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&pcie_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&pcie_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ qcom,calibration-variant = "QC_QCS615_Ride";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
+&pm8150_gpios {
+ usb2_en: usb2-en-state {
+ pins = "gpio10";
+ function = "normal";
+ output-enable;
+ power-source = <0>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs615/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs615/cdsp.mbn";
+
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ vmmc-supply = <&vreg_l17a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ status = "okay";
+};
+
+&spi6 {
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ clocks = <&can_osc>;
+ interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <10000000>;
+ vdd-supply = <&vreg_v3p3_can>;
+ xceiver-supply = <&vreg_v5p0_can>;
+ };
+};
+
+&tlmm {
+ bt_en_state: bt-en-state {
+ pins = "gpio85";
+ function = "gpio";
+ bias-pull-down;
+ };
+
+ pcie_default_state: pcie-default-state {
+ clkreq-pins {
+ pins = "gpio90";
+ function = "pcie_clk_req";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio89";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-pins {
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ wifi_reg_en_pins_state: wifi-reg-en-pins-state {
+ pins = "gpio91";
+ function = "gpio";
+ drive-strength = <8>;
+ output-high;
+ bias-pull-up;
+ };
+
+ wlan_en_state: wlan-en-state {
+ pins = "gpio84";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-down;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart7 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+ firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ };
+};
+
+/*
+ * USB0 routing and EDL mode:
+ *
+ * The USB0 high-speed differential pairs are routed via a mechanical
+ * switch controlled by an EDL-mode DIP switch (SW1).
+ *
+ * When the EDL DIP switch is enabled, the HS lines are routed to the
+ * Micro-USB connector, allowing the controller to operate in USB
+ * peripheral (device) mode for firmware flashing.
+ *
+ * In normal operation, the switch routes the HS lines to the onboard
+ * USB 3.0 hub. In this configuration, the Micro-USB connector is
+ * electrically disconnected and the controller can only operate in
+ * host mode.
+ *
+ * Due to this hardware design, USB0 is configured as host-only in the
+ * base device tree. A separate device-tree overlay may be used to
+ * describe the EDL-mode (peripheral-only) configuration.
+ */
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_2_hsphy {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy_2 {
+ vdda-phy-supply = <&vreg_l11a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17a>;
+ vcc-max-microamp = <600000>;
+ vccq2-supply = <&vreg_s4a>;
+ vccq2-max-microamp = <600000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&venus {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-usb1-peripheral.dtso b/arch/arm64/boot/dts/qcom/talos-evk-usb1-peripheral.dtso
new file mode 100644
index 000000000000..2f4630a6ba66
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-usb1-peripheral.dtso
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk.dts b/arch/arm64/boot/dts/qcom/talos-evk.dts
new file mode 100644
index 000000000000..af100e22beee
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "talos-evk-som.dtsi"
+
+/ {
+ model = "Qualcomm QCS615 IQ 615 EVK";
+ compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150";
+ chassis-type = "embedded";
+
+ aliases {
+ mmc1 = &sdhc_2;
+ };
+
+ dp0-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+
+ hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&mdss_dp0_out>;
+ };
+ };
+ };
+
+ hdmi_connector: hdmi-out {
+ compatible = "hdmi-connector";
+ type = "d";
+
+ port {
+ hdmi_con_out: endpoint {
+ remote-endpoint = <&adv7535_out>;
+ };
+ };
+ };
+
+ vreg_v1p8_out: regulator-v1p8-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v1p8-out";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v3p3_out: regulator-v3p3-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-out";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v5p0_out: regulator-v5p0-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-out";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ /* Powered by system 20V rail (USBC_VBUS_IN) */
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ hdmi_bridge: bridge@3d {
+ compatible = "adi,adv7535";
+ reg = <0x3d>;
+ avdd-supply = <&vreg_v1p8_out>;
+ dvdd-supply = <&vreg_v1p8_out>;
+ pvdd-supply = <&vreg_v1p8_out>;
+ a2vdd-supply = <&vreg_v1p8_out>;
+ v3p3-supply = <&vreg_v3p3_out>;
+ interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>;
+ adi,dsi-lanes = <4>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ adv7535_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ adv7535_out: endpoint {
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&adv7535_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_state_on>;
+ pinctrl-1 = <&sdc2_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vreg_l10a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos.dtsi b/arch/arm64/boot/dts/qcom/talos.dtsi
index c7dc507a50b5..cb32bfe732fb 100644
--- a/arch/arm64/boot/dts/qcom/talos.dtsi
+++ b/arch/arm64/boot/dts/qcom/talos.dtsi
@@ -4304,7 +4304,7 @@ osm_l3: interconnect@18321000 {
#interconnect-cells = <1>;
};
- usb_hsphy_1: phy@88e2000 {
+ usb_1_hsphy: phy@88e2000 {
compatible = "qcom,qcs615-qusb2-phy";
reg = <0x0 0x88e2000 0x0 0x180>;
@@ -4319,7 +4319,7 @@ usb_hsphy_1: phy@88e2000 {
status = "disabled";
};
- usb_hsphy_2: phy@88e3000 {
+ usb_2_hsphy: phy@88e3000 {
compatible = "qcom,qcs615-qusb2-phy";
reg = <0x0 0x088e3000 0x0 0x180>;
@@ -4412,7 +4412,7 @@ usb_1_dwc3: usb@a600000 {
iommus = <&apps_smmu 0x140 0x0>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usb_hsphy_1>, <&usb_qmpphy>;
+ phys = <&usb_1_hsphy>, <&usb_qmpphy>;
phy-names = "usb2-phy", "usb3-phy";
snps,dis-u1-entry-quirk;
@@ -4476,7 +4476,7 @@ usb_2_dwc3: usb@a800000 {
iommus = <&apps_smmu 0xe0 0x0>;
interrupts = <GIC_SPI 664 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usb_hsphy_2>;
+ phys = <&usb_2_hsphy>;
phy-names = "usb2-phy";
snps,dis_u2_susphy_quirk;
--
2.34.1
next prev parent reply other threads:[~2026-02-11 4:26 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-11 4:25 [PATCH v13 0/3] Add Qualcomm Technologies, Inc. Talos EVK SMARC support Sudarshan Shetty
2026-02-11 4:25 ` [PATCH v13 1/3] dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform Sudarshan Shetty
2026-02-11 4:25 ` [PATCH v13 2/3] arm64: dts: qcom: talos/qcs615-ride: Fix inconsistent USB PHY node naming Sudarshan Shetty
2026-02-11 4:25 ` Sudarshan Shetty [this message]
2026-02-11 6:16 ` [PATCH v13 3/3] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board Dmitry Baryshkov
2026-02-17 10:37 ` tessolveupstream
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260211042534.162007-4-tessolveupstream@gmail.com \
--to=tessolveupstream@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.