From: Chuck Lever <cel@kernel.org>
To: NeilBrown <neilb@ownmail.net>, Jeff Layton <jlayton@kernel.org>,
Olga Kornievskaia <okorniev@redhat.com>,
Dai Ngo <dai.ngo@oracle.com>, Tom Talpey <tom@talpey.com>
Cc: <linux-nfs@vger.kernel.org>, Chuck Lever <chuck.lever@oracle.com>
Subject: [PATCH v2 17/18] sunrpc: skip svc_xprt_enqueue in svc_xprt_received when idle
Date: Fri, 27 Feb 2026 09:03:44 -0500 [thread overview]
Message-ID: <20260227140345.40488-18-cel@kernel.org> (raw)
In-Reply-To: <20260227140345.40488-1-cel@kernel.org>
From: Chuck Lever <chuck.lever@oracle.com>
svc_xprt_received() unconditionally calls
svc_xprt_enqueue() after clearing XPT_BUSY. When no
work flags are pending, the enqueue traverses
svc_xprt_ready() -- executing an smp_rmb(), READ_ONCE(),
and tracepoint -- before returning false.
Trace data from a 256KB NFSv3 workload over RDMA shows
85% of svc_xprt_received() invocations reach
svc_xprt_enqueue() with no pending work flags. In the
WRITE phase, 167,335 of 196,420 calls find no work; in
the READ phase, 97,165 of 98,276. Each unnecessary call
executes a memory barrier, a flags read, and (when
tracing is active) fires the svc_xprt_enqueue
tracepoint.
Add a flags pre-check between clear_bit(XPT_BUSY) and
svc_xprt_enqueue(). Both the clear and the subsequent
READ_ONCE operate on the same xpt_flags word, so
cache-line serialization of the atomic bitops ensures
the read observes any flag set by a concurrent producer
before the line was acquired for the clear. If a
producer's set_bit occurs after the clear_bit, that
producer's own svc_xprt_enqueue() call observes
!XPT_BUSY and dispatches the transport.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
---
net/sunrpc/svc_xprt.c | 14 +++++++++++++-
1 file changed, 13 insertions(+), 1 deletion(-)
diff --git a/net/sunrpc/svc_xprt.c b/net/sunrpc/svc_xprt.c
index 73149280167c..36c8437cfd8d 100644
--- a/net/sunrpc/svc_xprt.c
+++ b/net/sunrpc/svc_xprt.c
@@ -234,7 +234,19 @@ void svc_xprt_received(struct svc_xprt *xprt)
svc_xprt_get(xprt);
smp_mb__before_atomic();
clear_bit(XPT_BUSY, &xprt->xpt_flags);
- svc_xprt_enqueue(xprt);
+
+ /*
+ * Skip the enqueue when no actionable flags are set.
+ * Each producer both sets its flag (XPT_DATA, XPT_CLOSE,
+ * etc.) and calls svc_xprt_enqueue(); if a set_bit races
+ * with this check, the producer's own enqueue observes
+ * !XPT_BUSY and dispatches the transport.
+ */
+ if (READ_ONCE(xprt->xpt_flags) &
+ (BIT(XPT_CONN) | BIT(XPT_CLOSE) | BIT(XPT_HANDSHAKE) |
+ BIT(XPT_DATA) | BIT(XPT_DEFERRED)))
+ svc_xprt_enqueue(xprt);
+
svc_xprt_put(xprt);
}
EXPORT_SYMBOL_GPL(svc_xprt_received);
--
2.53.0
next prev parent reply other threads:[~2026-02-27 14:04 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-27 14:03 [PATCH v2 00/18] svcrdma performance scalability enhancements Chuck Lever
2026-02-27 14:03 ` [PATCH v2 01/18] svcrdma: Add fair queuing for Send Queue access Chuck Lever
2026-02-27 14:03 ` [PATCH v2 02/18] svcrdma: Clean up use of rdma->sc_pd->device in Receive paths Chuck Lever
2026-02-27 14:03 ` [PATCH v2 03/18] svcrdma: Clean up use of rdma->sc_pd->device Chuck Lever
2026-02-27 14:03 ` [PATCH v2 04/18] svcrdma: Add Write chunk WRs to the RPC's Send WR chain Chuck Lever
2026-02-27 14:03 ` [PATCH v2 05/18] svcrdma: Factor out WR chain linking into helper Chuck Lever
2026-02-27 14:03 ` [PATCH v2 06/18] svcrdma: Reduce false sharing in struct svcxprt_rdma Chuck Lever
2026-02-27 14:03 ` [PATCH v2 07/18] svcrdma: Use lock-free list for Receive Queue tracking Chuck Lever
2026-02-27 14:03 ` [PATCH v2 08/18] svcrdma: Convert Read completion queue to use lock-free list Chuck Lever
2026-02-27 14:03 ` [PATCH v2 09/18] svcrdma: Release write chunk resources without re-queuing Chuck Lever
2026-02-27 14:03 ` [PATCH v2 10/18] svcrdma: Defer send context release to xpo_release_ctxt Chuck Lever
2026-02-27 14:03 ` [PATCH v2 11/18] svcrdma: Use watermark-based Receive Queue replenishment Chuck Lever
2026-02-27 14:03 ` [PATCH v2 12/18] svcrdma: Add per-recv_ctxt chunk context cache Chuck Lever
2026-02-27 14:03 ` [PATCH v2 13/18] svcrdma: clear XPT_DATA on sc_read_complete_q consumption Chuck Lever
2026-02-27 14:03 ` [PATCH v2 14/18] svcrdma: retry when receive queues drain transiently Chuck Lever
2026-02-27 14:03 ` [PATCH v2 15/18] svcrdma: clear XPT_DATA on sc_rq_dto_q consumption Chuck Lever
2026-02-27 14:03 ` [PATCH v2 16/18] sunrpc: skip svc_xprt_enqueue when no work is pending Chuck Lever
2026-02-27 14:03 ` Chuck Lever [this message]
2026-02-27 14:03 ` [PATCH v2 18/18] sunrpc: Skip xpt_reserved accounting for non-UDP transports Chuck Lever
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260227140345.40488-18-cel@kernel.org \
--to=cel@kernel.org \
--cc=chuck.lever@oracle.com \
--cc=dai.ngo@oracle.com \
--cc=jlayton@kernel.org \
--cc=linux-nfs@vger.kernel.org \
--cc=neilb@ownmail.net \
--cc=okorniev@redhat.com \
--cc=tom@talpey.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.