[PATCH V4 10/10] Documentation: Update VFIO NOIOMMU mode

[Jacob Pan <jacob.pan@linux.microsoft.com>]

Document the NOIOMMU mode with newly added cdev support under iommufd.

Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jacob Pan <jacob.pan@linux.microsoft.com>
---
 Documentation/driver-api/vfio.rst | 45 +++++++++++++++++++++++++++++--
 1 file changed, 43 insertions(+), 2 deletions(-)

diff --git a/Documentation/driver-api/vfio.rst b/Documentation/driver-api/vfio.rst
index 2a21a42c9386..da6f77414c3b 100644
--- a/Documentation/driver-api/vfio.rst
+++ b/Documentation/driver-api/vfio.rst
@@ -275,8 +275,6 @@ in a VFIO group.
 With CONFIG_VFIO_DEVICE_CDEV=y the user can now acquire a device fd
 by directly opening a character device /dev/vfio/devices/vfioX where
 "X" is the number allocated uniquely by VFIO for registered devices.
-cdev interface does not support noiommu devices, so user should use
-the legacy group interface if noiommu is wanted.
 
 The cdev only works with IOMMUFD.  Both VFIO drivers and applications
 must adapt to the new cdev security model which requires using
@@ -370,6 +368,49 @@ IOMMUFD IOAS/HWPT to enable userspace DMA::
 
 	/* Other device operations as stated in "VFIO Usage Example" */
 
+VFIO NOIOMMU mode
+-------------------------------------------------------------------------------
+VFIO also supports a no-IOMMU mode, intended for usages where unsafe DMA can
+be performed by userspace drivers w/o physical IOMMU protection. This mode
+is controlled by the parameter:
+
+/sys/module/vfio/parameters/enable_unsafe_noiommu_mode
+
+Upon enabling this mode, with an assigned device, the user will be presented
+with a VFIO group and device file, e.g.::
+
+  /dev/vfio/
+  |-- devices
+  |   `-- noiommu-vfio0	/* VFIO device cdev */
+  |-- noiommu-0		/* VFIO group */
+  `-- vfio
+
+The capabilities vary depending on the device programming interface and kernel
+configuration used. The following table summarizes the differences:
+
++-------------------+---------------------+----------------------+
+| Feature           | VFIO group          | VFIO device cdev     |
++===================+=====================+======================+
+| VFIO device UAPI  | Yes                 | Yes                  |
++-------------------+---------------------+----------------------+
+| VFIO container    | No                  | No                   |
++-------------------+---------------------+----------------------+
+| IOMMUFD IOAS      | No                  | Yes*                 |
++-------------------+---------------------+----------------------+
+
+Note that the VFIO container case includes IOMMUFD provided VFIO compatibility
+interfaces when either CONFIG_VFIO_CONTAINER or CONFIG_IOMMUFD_VFIO_CONTAINER is
+enabled.
+
+* IOMMUFD UAPI is available for VFIO device cdev to pin and map user memory with
+  the ability to retrieve physical addresses for DMA command submission.
+
+A new IOMMUFD ioctl IOMMU_IOAS_GET_PA is added to retrieve the physical address
+for a given user virtual address. Note that IOMMU_IOAS_MAP_FIXED_IOVA flag is
+ignored in no-IOMMU mode since there is no physical DMA remapping hardware.
+tools/testing/selftests/vfio/vfio_iommufd_noiommu_test.c provides an example of
+using this ioctl in no-IOMMU mode.
+
 VFIO User API
 -------------------------------------------------------------------------------
 
-- 
2.34.1