[PATCH v6 10/10] arm64: dts: Add support for LX2160 Twins board in single configuration

[Josua Mayer <josua@solid-run.com>]

Add support for the SolidRun LX2160A Twins board in its single cpu
configuration.

The twins board is designed to host a pair of LX2160A CEX-7 modules,
sharing a single PCI-E connector in multi-host mode.

It may be assembled in two configurations (different assembly options
facilitating signal re-routing), with a single or with dual CEX-7
module. Their marketing names are:

- SolidWAN Single LX2160
- SolidWAN Dual LX2160

This patch adds the single configuration, featuring:
- 8x SFP (1Gbps)
- 8x SFP+ (1/10Gbps)
- PCI-E OCP card connector
- USB-3.0 front-panel header with single port
- microSD
- dual hot-swappable power supplies

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 arch/arm64/boot/dts/freescale/Makefile             |   2 +
 .../boot/dts/freescale/fsl-lx2160a-half-twins.dts  | 826 +++++++++++++++++++++
 2 files changed, 828 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 711e36cc2c990..59eee431562ef 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -51,6 +51,8 @@ DTC_FLAGS_fsl-lx2160a-bluebox3-rev-a := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
 DTC_FLAGS_fsl-lx2160a-clearfog-cx := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
+DTC_FLAGS_fsl-lx2160a-half-twins := -Wno-interrupt_map
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-half-twins.dtb
 DTC_FLAGS_fsl-lx2160a-honeycomb := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
 DTC_FLAGS_fsl-lx2160a-qds := -Wno-interrupt_map
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts
new file mode 100644
index 0000000000000..ee1867f5b2b6b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts
@@ -0,0 +1,826 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for single LX2160A CEX-7 on Twins board.
+//
+// Copyright 2022 SolidRun Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+
+#include "fsl-lx2160a-rev2.dtsi"
+#include "fsl-lx2160a-cex7.dtsi"
+
+/ {
+	compatible = "solidrun,twins-single", "solidrun,lx2160a-cex7", "fsl,lx2160a";
+	model = "SolidRun LX2160A SolidWAN Single";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &expander0;
+		gpio5 = &expander1;
+		gpio6 = &expander2;
+		gpio7 = &expander3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c2;
+		i2c2 = &i2c4;
+		i2c3 = &fan_i2c;
+		i2c4 = &power_i2c;
+		i2c5 = &i2c_smb;
+		i2c6 = &sfp0_i2c;
+		i2c7 = &sfp1_i2c;
+		i2c8 = &sfp2_i2c;
+		i2c9 = &sfp3_i2c;
+		i2c10 = &twins_sfp_c1_at_i2c;
+		i2c11 = &twins_sfp_c1_ab_i2c;
+		i2c12 = &twins_sfp_c1_bt_i2c;
+		i2c13 = &twins_sfp_c1_bb_i2c;
+		i2c14 = &twins_sfp_c2_at_i2c;
+		i2c15 = &twins_sfp_c2_ab_i2c;
+		i2c16 = &twins_sfp_c2_bt_i2c;
+		i2c17 = &twins_sfp_c2_bb_i2c;
+		i2c18 = &twins_sfp_c3_at_i2c;
+		i2c19 = &twins_sfp_c3_ab_i2c;
+		i2c20 = &twins_sfp_c3_bt_i2c;
+		i2c21 = &twins_sfp_c3_bb_i2c;
+		i2c22 = &htwins_sfp_c3_at_i2c;
+		i2c23 = &htwins_sfp_c3_ab_i2c;
+		i2c24 = &htwins_sfp_c3_bt_i2c;
+		i2c25 = &htwins_sfp_c3_bb_i2c;
+		i2c26 = &ddr_i2c;
+		mmc0 = &esdhc0;
+		mmc1 = &esdhc1;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_ht_c3_bt: led-sfp-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&expander3 14 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac5>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_ht_c3_bb: led-sfp-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&expander3 13 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac15>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_ht_c3_at: led-sfp-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&expander3 11 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac6>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_ht_c3_ab: led-sfp-4 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <4>;
+			gpios = <&expander3 12 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac11>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c1_bt: led-sfp-9 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <9>;
+			gpios = <&expander1 4 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac4>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c1_bb: led-sfp-10 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <10>;
+			gpios = <&expander1 3 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac17>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c1_at: led-sfp-11 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <11>;
+			gpios = <&expander1 1 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac3>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c1_ab: led-sfp-12 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <12>;
+			gpios = <&expander1 2 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac12>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c2_bt: led-sfp-13 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <13>;
+			gpios = <&expander1 10 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac8>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c2_bb: led-sfp-14 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <14>;
+			gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac16>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c2_at: led-sfp-15 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <15>;
+			gpios = <&expander1 5 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac7>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c2_ab: led-sfp-16 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <16>;
+			gpios = <&expander1 6 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac18>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c3_bt: led-sfp-17 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <17>;
+			gpios = <&expander1 14 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac10>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c3_bb: led-sfp-18 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <18>;
+			gpios = <&expander1 13 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac14>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c3_at: led-sfp-19 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <19>;
+			gpios = <&expander1 11 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac9>;
+			linux,default-trigger = "netdev";
+		};
+
+		led_c3_ab: led-sfp-20 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <20>;
+			gpios = <&expander1 12 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&dpmac13>;
+			linux,default-trigger = "netdev";
+		};
+
+		led-status {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <0>;
+			gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-status-twin {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <1>;
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fault {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_FAULT;
+			function-enumerator = <0>;
+			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			panic-indicator;
+		};
+
+		led-fault-twin {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_FAULT;
+			function-enumerator = <1>;
+			gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		/*
+		 * This gpio controlled mux can route the tacho signals of 6 PWM FAN connectors
+		 * to the tacho inputs of both CEX-7 modules (twins).
+		 *
+		 * The first twin controls this mux and monitors four fan connectors, two intended
+		 * for itself, and two for the OCP card.
+		 *
+		 * The second twin monitors only two fan connectors intended for itself.
+		 *
+		 * The table below maps selector GPIO states to monitored fan connector per twin:
+		 *
+		 * | SEL1 | SEL0 | Twin 1 | Twin 2 |
+		 * | ---: | ---: | :------| ------ |
+		 * |    0 |    0 | J10    |  J5024 |
+		 * |    0 |    1 | J5016  |  J5024 |
+		 * |    1 |    0 | J5026  |  J5025 |
+		 * |    1 |    1 | J5013  |  J5025 |
+		 */
+		mux-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>, /* SEL0 */
+			    <&expander0 15 GPIO_ACTIVE_HIGH>; /* SEL1 */
+	};
+
+	ht_c3_bt_sfp: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&htwins_sfp_c3_bt_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander2 13 GPIO_ACTIVE_LOW>;
+	};
+
+	ht_c3_bb_sfp: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&htwins_sfp_c3_bb_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander2 14 GPIO_ACTIVE_LOW>;
+	};
+
+	ht_c3_at_sfp: sfp-3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&htwins_sfp_c3_at_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander2 11 GPIO_ACTIVE_LOW>;
+	};
+
+	ht_c3_ab_sfp: sfp-4 {
+		compatible = "sff,sfp";
+		i2c-bus = <&htwins_sfp_c3_ab_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander2 12 GPIO_ACTIVE_LOW>;
+	};
+
+	c1_bt_sfp: sfp-9 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c1_bt_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>;
+	};
+
+	c1_bb_sfp: sfp-10 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c1_bb_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 4 GPIO_ACTIVE_LOW>;
+	};
+
+	c1_at_sfp: sfp-11 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c1_at_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
+	};
+
+	c1_ab_sfp: sfp-12 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c1_ab_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 2 GPIO_ACTIVE_LOW>;
+	};
+
+	c2_bt_sfp: sfp-13 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c2_bt_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 9 GPIO_ACTIVE_LOW>;
+	};
+
+	c2_bb_sfp: sfp-14 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c2_bb_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 10 GPIO_ACTIVE_LOW>;
+	};
+
+	c2_at_sfp: sfp-15 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c2_at_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;
+	};
+
+	c2_ab_sfp: sfp-16 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c2_ab_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 6 GPIO_ACTIVE_LOW>;
+	};
+
+	c3_bt_sfp: sfp-17 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c3_bt_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 13 GPIO_ACTIVE_LOW>;
+	};
+
+	c3_bb_sfp: sfp-18 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c3_bb_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 14 GPIO_ACTIVE_LOW>;
+	};
+
+	c3_at_sfp: sfp-19 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c3_at_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 11 GPIO_ACTIVE_LOW>;
+	};
+
+	c3_ab_sfp: sfp-20 {
+		compatible = "sff,sfp";
+		i2c-bus = <&twins_sfp_c3_ab_i2c>;
+		maximum-power-milliwatt = <2000>;
+		mod-def0-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/*
+ * This board supports industrial grade temperatures,
+ * the LX2160A SoC maximum junction temperature is 105°C.
+ *
+ * Raise thermal thresholds to allow operation near maximum temperature.
+ */
+&ccn_dpaa_alert {
+	temperature = <100000>;
+};
+
+&ccn_dpaa_crit {
+	temperature = <105000>;
+};
+
+&cluster2_3_alert {
+	temperature = <100000>;
+};
+
+&cluster2_3_crit {
+	temperature = <105000>;
+};
+
+&cluster4_alert {
+	temperature = <100000>;
+};
+
+&cluster4_crit {
+	temperature = <105000>;
+};
+
+&cluster5_alert {
+	temperature = <100000>;
+};
+
+&cluster5_crit {
+	temperature = <105000>;
+};
+
+&cluster6_7_alert {
+	temperature = <100000>;
+};
+
+&cluster6_7_crit {
+	temperature = <105000>;
+};
+
+&dce_qbman_alert {
+	temperature = <100000>;
+};
+
+&dce_qbman_crit {
+	temperature = <105000>;
+};
+
+/* sfp port 11 */
+&dpmac3 {
+	managed = "in-band-status";
+	phys = <&serdes_1 7>;
+	sfp = <&c1_at_sfp>;
+};
+
+/* sfp port 9 */
+&dpmac4 {
+	managed = "in-band-status";
+	phys = <&serdes_1 6>;
+	sfp = <&c1_bt_sfp>;
+};
+
+/* sfp port 1 */
+&dpmac5 {
+	managed = "in-band-status";
+	phys = <&serdes_1 5>;
+	sfp = <&ht_c3_bt_sfp>;
+};
+
+/* sfp port 3 */
+&dpmac6 {
+	managed = "in-band-status";
+	phys = <&serdes_1 4>;
+	sfp = <&ht_c3_at_sfp>;
+};
+
+/* sfp port 15 */
+&dpmac7 {
+	managed = "in-band-status";
+	phys = <&serdes_1 3>;
+	sfp = <&c2_at_sfp>;
+};
+
+/* sfp port 13 */
+&dpmac8 {
+	managed = "in-band-status";
+	phys = <&serdes_1 2>;
+	sfp = <&c2_bt_sfp>;
+};
+
+/* sfp port 19 */
+&dpmac9 {
+	managed = "in-band-status";
+	phys = <&serdes_1 1>;
+	sfp = <&c3_at_sfp>;
+};
+
+/* sfp port 17 */
+&dpmac10 {
+	managed = "in-band-status";
+	phys = <&serdes_1 0>;
+	sfp = <&c3_bt_sfp>;
+};
+
+/* sfp port 4 */
+&dpmac11 {
+	managed = "in-band-status";
+	phys = <&serdes_2 0>;
+	sfp = <&ht_c3_ab_sfp>;
+};
+
+/* sfp port 12 */
+&dpmac12 {
+	managed = "in-band-status";
+	phys = <&serdes_2 1>;
+	sfp = <&c1_ab_sfp>;
+};
+
+/* sfp port 20 */
+&dpmac13 {
+	managed = "in-band-status";
+	phys = <&serdes_2 6>;
+	sfp = <&c3_ab_sfp>;
+};
+
+/* sfp port 18 */
+&dpmac14 {
+	managed = "in-band-status";
+	phys = <&serdes_2 7>;
+	sfp = <&c3_bb_sfp>;
+};
+
+/* sfp port 2 */
+&dpmac15 {
+	managed = "in-band-status";
+	phys = <&serdes_2 4>;
+	sfp = <&ht_c3_bb_sfp>;
+};
+
+/* sfp port 14 */
+&dpmac16 {
+	managed = "in-band-status";
+	phys = <&serdes_2 5>;
+	sfp = <&c2_bb_sfp>;
+};
+
+/* sfp port 10 */
+&dpmac17 {
+	/* override connection to on-COM phy */
+	/delete-property/ phy-handle;
+	/delete-property/ phy-connection-type;
+	managed = "in-band-status";
+	phys = <&serdes_2 2>;
+	sfp = <&c1_bb_sfp>;
+};
+
+/* sfp port 16 */
+&dpmac18 {
+	managed = "in-band-status";
+	phys = <&serdes_2 3>;
+	sfp = <&c2_ab_sfp>;
+};
+
+&esdhc0 {
+	pinctrl-0 = <&esdhc0_cd_wp_pins>, <&esdhc0_cmd_data30_clk_vsel_pins>;
+	pinctrl-names = "default";
+	/*
+	 * Disable 1.8V modes so that microsd state is same between
+	 * power-on-reset, u-boot and linux.
+	 * This avoids sporadic read errors after hard reset with some cards.
+	 */
+	no-1-8-v;
+	status = "okay";
+};
+
+&i2c2 {
+	expander0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	expander1: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	expander2: gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	expander3: gpio@25 {
+		compatible = "nxp,pca9555";
+		reg = <0x25>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	/* Half twins configuration; take over c3 from the other twin side */
+	i2c-mux@73 {
+		compatible = "nxp,pca9547";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		htwins_sfp_c3_at_i2c: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		htwins_sfp_c3_ab_i2c: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		htwins_sfp_c3_bt_i2c: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		htwins_sfp_c3_bb_i2c: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9547";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		twins_sfp_c1_at_i2c: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c1_ab_i2c: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c1_bt_i2c: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c1_bb_i2c: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c2_at_i2c: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c2_ab_i2c: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		twins_sfp_c2_bt_i2c: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c2_bb_i2c: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c3_at_i2c: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c3_ab_i2c: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c3_bt_i2c: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		twins_sfp_c3_bb_i2c: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&pcie5 {
+	status = "okay";
+};
+
+&pcs_mdio3 {
+	status = "okay";
+};
+
+&pcs_mdio4 {
+	status = "okay";
+};
+
+&pcs_mdio5 {
+	status = "okay";
+};
+
+&pcs_mdio6 {
+	status = "okay";
+};
+
+&pcs_mdio7 {
+	status = "okay";
+};
+
+&pcs_mdio8 {
+	status = "okay";
+};
+
+&pcs_mdio9 {
+	status = "okay";
+};
+
+&pcs_mdio10 {
+	status = "okay";
+};
+
+&pcs_mdio11 {
+	status = "okay";
+};
+
+&pcs_mdio12 {
+	status = "okay";
+};
+
+&pcs_mdio13 {
+	status = "okay";
+};
+
+&pcs_mdio14 {
+	status = "okay";
+};
+
+&pcs_mdio15 {
+	status = "okay";
+};
+
+&pcs_mdio16 {
+	status = "okay";
+};
+
+&pcs_mdio17 {
+	status = "okay";
+};
+
+&pcs_mdio18 {
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	/*
+	 * COM has a phy at address 1 connected to SoC Ethernet Controller 1.
+	 * It competes for WRIOP MAC17, and no connector has been wired.
+	 */
+	status = "disabled";
+};
+
+&serdes_2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&wriop_alert {
+	temperature = <100000>;
+};
+
+&wriop_crit {
+	temperature = <105000>;
+};

-- 
2.51.0