From: Ryan Chen <ryan_chen@aspeedtech.com>
To: <jk@codeconstruct.com.au>, <andriy.shevchenko@linux.intel.com>,
Andi Shyti <andi.shyti@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>,
Andrew Jeffery <andrew@codeconstruct.com.au>,
"Benjamin Herrenschmidt" <benh@kernel.crashing.org>,
Rayn Chen <rayn_chen@aspeedtech.com>,
Philipp Zabel <p.zabel@pengutronix.de>
Cc: <linux-i2c@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-aspeed@lists.ozlabs.org>, <linux-kernel@vger.kernel.org>,
<openbmc@lists.ozlabs.org>, Ryan Chen <ryan_chen@aspeedtech.com>
Subject: [PATCH RESEND v29 4/4] i2c: ast2600: Add target mode support
Date: Wed, 13 May 2026 13:32:03 +0800 [thread overview]
Message-ID: <20260513-upstream_i2c-v29-4-fe9926964d55@aspeedtech.com> (raw)
In-Reply-To: <20260513-upstream_i2c-v29-0-fe9926964d55@aspeedtech.com>
Add target mode support to the AST2600 I2C driver.
Target mode features implemented include:
- Add target interrupt handling
- Address match and response logic
This complements the existing controller-mode support, enabling
dual-role capability.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
---
Changes in v29:
- fix race between unreg_target and IRQ handler.
- move i2cs ier enable from ast2600_i2c_init to probe after master ier enable.
- remove dma/byte transfer, use buffer mode only.
Changes in v28:
- fix typo condication -> condition
- fix compile error, when disable CONFIG_I2C_SLAVE
Changes in v26:
- change int to bool target_operate
- rename target_operate to target_active
- use i2c_bus->target replace require IO
- use WRITE_ONCE replace target_operate write.
---
drivers/i2c/busses/i2c-ast2600.c | 340 +++++++++++++++++++++++++++++++++++++++
1 file changed, 340 insertions(+)
diff --git a/drivers/i2c/busses/i2c-ast2600.c b/drivers/i2c/busses/i2c-ast2600.c
index 787ef6bd6244..137aaf7e26b5 100644
--- a/drivers/i2c/busses/i2c-ast2600.c
+++ b/drivers/i2c/busses/i2c-ast2600.c
@@ -254,6 +254,11 @@ struct ast2600_i2c_bus {
size_t buf_size;
bool multi_master;
void __iomem *buf_base;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* target structure */
+ bool target_active;
+ struct i2c_client *target;
+#endif
};
static void ast2600_i2c_ac_timing_config(struct ast2600_i2c_bus *i2c_bus)
@@ -337,6 +342,243 @@ static int ast2600_i2c_recover_bus(struct ast2600_i2c_bus *i2c_bus)
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static void ast2600_i2c_target_packet_buff_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+ int target_rx_len = 0;
+ u32 cmd = 0;
+ u8 value;
+ int i;
+
+ /* due to controller target is common buffer, need force the master stop not issue */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_CMD_STS) & GENMASK(15, 0)) {
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+ i2c_bus->cmd_err = -EBUSY;
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ complete(&i2c_bus->cmd_complete);
+ }
+
+ /* Handle i2c target timeout condition */
+ if (AST2600_I2CS_INACTIVE_TO & sts) {
+ /* Reset timeout counter */
+ u32 ac_timing = readl(i2c_bus->reg_base + AST2600_I2CC_AC_TIMING) &
+ AST2600_I2CC_AC_TIMING_MASK;
+
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ ac_timing |= AST2600_I2CC_TTIMEOUT(i2c_bus->timeout);
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ writel(TARGET_TRIGGER_CMD, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ WRITE_ONCE(i2c_bus->target_active, false);
+ return;
+ }
+
+ sts &= ~(AST2600_I2CS_PKT_DONE | AST2600_I2CS_PKT_ERROR);
+
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ WRITE_ONCE(i2c_bus->target_active, true);
+
+ switch (sts) {
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_STOP:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ fallthrough;
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD;
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ }
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_RX_BUFF_EN)
+ cmd = 0;
+ else
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_RX_DONE:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE |
+ AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_STOP:
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writeb(value, i2c_bus->buf_base);
+ break;
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writeb(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA:
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ } else {
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_PROCESSED, &value);
+ }
+ writeb(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ /* workaround : trigger the cmd twice to fix next state keep 1000000 */
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ break;
+ case AST2600_I2CS_TX_NAK | AST2600_I2CS_STOP:
+ case AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ default:
+ dev_dbg(i2c_bus->dev, "unhandled target isr case %x, sts %x\n", sts,
+ readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+ break;
+ }
+
+ if (cmd)
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if ((sts & AST2600_I2CS_STOP) && !(sts & AST2600_I2CS_SLAVE_PENDING))
+ WRITE_ONCE(i2c_bus->target_active, false);
+}
+
+static int ast2600_i2c_target_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 ier = readl(i2c_bus->reg_base + AST2600_I2CS_IER);
+ u32 isr = readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if (!(isr & ier))
+ return 0;
+
+ /*
+ * Target interrupt coming after controller packet done
+ * So need handle controller first.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_ISR) & AST2600_I2CM_PKT_DONE)
+ return 0;
+
+ isr &= ~(AST2600_I2CS_ADDR_INDICATE_MASK);
+
+ if (AST2600_I2CS_ADDR1_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR1_NAK;
+
+ if (AST2600_I2CS_ADDR2_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR2_NAK;
+
+ if (AST2600_I2CS_ADDR3_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR3_NAK;
+
+ if (AST2600_I2CS_ADDR_MASK & isr)
+ isr &= ~AST2600_I2CS_ADDR_MASK;
+
+ if (AST2600_I2CS_PKT_DONE & isr)
+ ast2600_i2c_target_packet_buff_irq(i2c_bus, isr);
+
+ return 1;
+}
+#endif
+
static int ast2600_i2c_setup_buff_tx(u32 cmd, struct ast2600_i2c_bus *i2c_bus)
{
struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
@@ -498,6 +740,20 @@ static void ast2600_i2c_controller_packet_irq(struct ast2600_i2c_bus *i2c_bus, u
}
break;
case AST2600_I2CM_RX_DONE:
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /*
+ * Workaround for controller/target packet mode enable rx done stuck issue
+ * When controller go for first read (RX_DONE), target mode will also effect
+ * Then controller will send nack, not operate anymore.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_PKT_MODE_EN) {
+ u32 target_cmd = readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(target_cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ }
+ fallthrough;
+#endif
case AST2600_I2CM_RX_DONE | AST2600_I2CM_NORMAL_STOP:
/* do next rx */
xfer_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
@@ -584,6 +840,12 @@ static irqreturn_t ast2600_i2c_bus_irq(int irq, void *dev_id)
{
struct ast2600_i2c_bus *i2c_bus = dev_id;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target) {
+ if (ast2600_i2c_target_irq(i2c_bus))
+ return IRQ_HANDLED;
+ }
+#endif
return IRQ_RETVAL(ast2600_i2c_controller_irq(i2c_bus));
}
@@ -600,12 +862,31 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target_active)
+ return -EBUSY;
+ /*
+ * Controller and target share the same buffer register. A target
+ * transaction can update buffer state asynchronously via IRQ, so block
+ * controller transfers while target is active to avoid buffer corruption.
+ */
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_IER);
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR) || i2c_bus->target_active) {
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+ return -EBUSY;
+ }
+#endif
+
i2c_bus->cmd_err = 0;
i2c_bus->msgs = msgs;
i2c_bus->msgs_index = 0;
i2c_bus->msgs_count = num;
reinit_completion(&i2c_bus->cmd_complete);
ret = ast2600_i2c_do_start(i2c_bus);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* avoid race condition target is wait and controller wait 1st target operate */
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
if (ret)
goto controller_out;
timeout = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
@@ -624,6 +905,9 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
* if the bus is still busy.
*/
if (i2c_bus->multi_master &&
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ !i2c_bus->target_active &&
+#endif
(readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) &
AST2600_I2CC_BUS_BUSY_STS))
ast2600_i2c_recover_bus(i2c_bus);
@@ -659,8 +943,54 @@ static int ast2600_i2c_init(struct ast2600_i2c_bus *i2c_bus)
/* Clear Interrupt */
writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CM_ISR);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CS_ISR);
+#endif
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static int ast2600_i2c_reg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 cmd = TARGET_TRIGGER_CMD;
+
+ if (i2c_bus->target)
+ return -EINVAL;
+
+ dev_dbg(i2c_bus->dev, "target addr %x\n", client->addr);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+ writel(AST2600_I2CC_SLAVE_EN | readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL),
+ i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ i2c_bus->target = client;
+ /* Set target addr. */
+ writel(client->addr | AST2600_I2CS_ADDR1_ENABLE,
+ i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ return 0;
+}
+
+static int ast2600_i2c_unreg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 val;
+
+ /* Turn off target mode. */
+ val = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(val & ~AST2600_I2CC_SLAVE_EN, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ val = readl(i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+ writel(val & ~AST2600_I2CS_ADDR1_MASK, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ synchronize_irq(i2c_bus->irq);
+ i2c_bus->target = NULL;
+
return 0;
}
+#endif
static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
{
@@ -670,6 +1000,10 @@ static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
static const struct i2c_algorithm i2c_ast2600_algorithm = {
.xfer = ast2600_i2c_controller_xfer,
.functionality = ast2600_i2c_functionality,
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ .reg_target = ast2600_i2c_reg_target,
+ .unreg_target = ast2600_i2c_unreg_target,
+#endif
};
static int ast2600_i2c_probe(struct platform_device *pdev)
@@ -708,6 +1042,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
regmap_write(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, I2CCG_DIV_CTRL);
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ WRITE_ONCE(i2c_bus->target_active, false);
+#endif
i2c_bus->dev = dev;
i2c_bus->multi_master = device_property_read_bool(dev, "multi-master");
@@ -765,6 +1102,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
i2c_bus->reg_base + AST2600_I2CM_IER);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
ret = devm_i2c_add_adapter(dev, &i2c_bus->adap);
if (ret)
--
2.34.1
next prev parent reply other threads:[~2026-05-13 5:32 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-13 5:31 [PATCH RESEND v29 0/4] Add ASPEED AST2600 I2C controller driver Ryan Chen
2026-05-13 5:32 ` [PATCH RESEND v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML Ryan Chen
2026-05-13 17:05 ` Rob Herring (Arm)
2026-05-14 1:52 ` sashiko-bot
2026-05-13 5:32 ` [PATCH RESEND v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties Ryan Chen
2026-05-13 17:05 ` Rob Herring (Arm)
2026-05-13 5:32 ` [PATCH RESEND v29 3/4] i2c: ast2600: Add controller driver for AST2600 new register set Ryan Chen
2026-05-14 2:47 ` sashiko-bot
2026-05-13 5:32 ` Ryan Chen [this message]
2026-05-14 3:22 ` [PATCH RESEND v29 4/4] i2c: ast2600: Add target mode support sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260513-upstream_i2c-v29-4-fe9926964d55@aspeedtech.com \
--to=ryan_chen@aspeedtech.com \
--cc=andi.shyti@kernel.org \
--cc=andrew@codeconstruct.com.au \
--cc=andriy.shevchenko@linux.intel.com \
--cc=benh@kernel.crashing.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jk@codeconstruct.com.au \
--cc=joel@jms.id.au \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=openbmc@lists.ozlabs.org \
--cc=p.zabel@pengutronix.de \
--cc=rayn_chen@aspeedtech.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.